Gree KY-32Na/D User manual

AIRCONDITIONER
MOBILE
Please read this manual carefully before operating the unit.
OWNER'S MANUAL
MOBILE AIR CONDITIONER GREE ELECTRIC APPLIANCES, INC. OF ZHUHAI
KY-32Na/D
KYD-32Na/D

.................................................
1
........................................... .
........................................... .
.............................................
................................................
22
............................................... 24
23
2
1
3
..................................．．．．．．．．
...............．．．．．．．．
..................................．．．．．．．．
..................................．．．．．．．．
..................................．．．．．．．．
.................................．．．．．．．．
17-19
20-21
.............................................
11
12
13
14
15
16
.................．．．．．．．
4-8
9-10
...............
CONTENTS
Summary
Working principle
Models and specifications
..................................................
Structure
Operating methods
Names and Functions of the Remote Controller
COOL mode operation
HEATmode operation (only for cooling/heating type units)
DRYmode operation
SLEEP mode operation
AUTO mode operation
TIMER mode operation
Installation guide for castor, drainage pipe and air exhaust accessory
Care and Maintenance
Troubleshooting
User notices
After service
.........................................
.........．．．．．．．
.........................................

－2－
SUMMARY
－1－
GREE MOBILE AIR CONDITIONER is a small, moveable air conditioner. It possess the
functionsofCOOL,HEAT,DRYandtheSeparateVentilation,anddependsondifferentplaces,it
canbemovedatwill.Itisfitforhome andofficeuse,especiallyfitforthehousewithmanyrooms.
With the compact configuration, excellent workmanship, elegant appearance, it looks like a standing
Benz car, it is convenient for moving, energy saving, and low noise.
Note: Please read this manual carefully before operating the unit, the manual is used for reference,
andthetechnicalparameters aresubjecttochangewithoutnotice.
WORKING PRINCIPLE
With the help of upper motor, the airflow of indoor passes through the evaporator becomes the
cooling wind,butwiththehelpoflowermotor,theairflowofindoorpassesthroughthecondenser
becomestheheating wind.ItwasdesignedtwoductsystemsinitsstructureTheheating windisdischarged
bytherearoutlet,thecooling windisdischargedbythefrontoutlet,flow-guidedbythelouver,andit
brings the gentle cooling airflow, and the low temperature environment is maintained.
The Working Principle
Cooling wind
Upper
motor
Lower
motor
Evaporator
Airflow 1
Airflow 2
Capillary
Heating wind
Condenser

－2－
KY-32Na/D
3200W
KYD-32Na/D
3200W/2000W
230V
50Hz
5.2A
5.65A
1200W
1245W
5.2A/8.0A
5.65A/8.0A
1200W/2050W
1245W/1850W
330m3/h
410A 0.58Kg
56dB(A)
45 kg
80.0×37.040.0×
44.4
63.4×
84.0×
MODELS AND SPECIFICATIONS
Model
Cooling/heating capacity
Rated voltage
Rated frequency
Cooling/heating rated current
The max. cooling/heating input current
Cooling/heating rated power
The max. input power
Recycling air volume
Refrigerant and refrigerant charging
Noise(sound intensity level)
Weight (net weight)
The dimensions of unit
(Height×Width×Depth) (cm)
The dimensions of packaging
(Height×Width×Depth) (cm)
Note:
1. The cooling capacity was tested in the condition of the indoor dry bulb temp.30℃, wet bulb
temp.25.5℃(the temp of indoor and outdoor are same) there is no exhaust pipe, the heating capacity
was tested in the condition of the indoor dry bulb temp.20℃, wet bulb temp.12℃.
2. The max. input power was tested the indoor dry bulb temp. 32℃,the wet bulb temp.23℃was
tested in the cooling mode.
3.The technical parameters are subject to change without notice. Please refer to the nameplate of the unit.

－3－
STRUCTURE
Controlling panel
Air outlet
Handle
Lower air inlet
Front
Rear
Upper air inlet grille
Power cable
Air exhaust outlet
Lower air inlet grille

OPERATING METHODS
－4－
The working range is 16℃-30℃.
When operating, the unit should be placed on the horizontal place, more
than 50cm away from the wall or other obstructions.
The working range of COOL mode and DRY mode.
Location requirement
Power supply Before the unit is power-on, please check the following:
The standard working range of the voltage is 220/240V 6%, 50Hz,
if the voltage is higher or lower, the air conditioner will be affected.
● The lead wire is suitable for more than 20A start-up current, in order
to avoid the voltage decline when the unit starts suddenly.
● The power plugs and the sockets can be supported by the current
that is more than 16A.
● The thread section of the lead wires and any continued use lead wire
is no less than 2.5mm2.
● If the power supply cord is damaged, should adopt the special
power supply cord to replace.
● If the power supply is needed to replace or maintain, please
contact with the dealer and ask for the professional to do
the repairing work.
● The air conditioner must be safety earthed. Earth wire must be
connected to the special device of the building. In order to provide
the good earthing for the air conditioner.
５
０ｃ
ｍ
５０ｃｍ

OPERATING METHODS
●Can not use the steel wire or the brass wire replace the fuse, the
capability of the fuse must be appropriate. In order to avoid the power
cord damaged and electrical leakage, do not fix the power supply on the
knife edge or the sharp object.
●The wiring must be operated by the professional and according
to the national regulations, in fixed circuit, there must be electricity
leakage protection switch of enough power capacity and 16A thermal-
magnetic breaker air switch with enough space, the earth wire can't be
connected to the water pipe or the gas pipe, when the air
is not used, please pull out the power plug or cut off the power supply.
conditioner
－5－
There must be reliable ground
wire in the power supply
Earthing
Water pipe
Gas pipe
If the supply cord is damaged, it must be replaced by the
manufacturer, its service agent or similarly qualified persons in
order to avoid hazard.
●

－6－
ON/OFF
FAN TEMP TIMER SLEEP
OFF
ON
LOW MD HIGH
OPERATING METHODS
LCD instruction (dynamic display)
SLEEP
COOL
FAN
SET TIME DISPLAY
HEAT
DRY
SLEEP
COOL
HEAT
DRY
SET TEMP
AUTO
SET TIME
SETTEMP
AUTO
FANSPEED
SETTIMERON/OFF
NamesandFunctions-RemoteController
ON/OFF
MODE
FANSPEED
LCD Display
SETTEMP
SETTIMER
SETSLEEP
MODE

－7－
OPERATING METHODS
Control panel and the function
1. "ON/ OFF "
Press once to start and press once more to stop the unit.
2."MODE"
Press this button to change the operation mode in order of:
ＦＡＮ → ＣＯＯＬ →ＨＥＡＴ→ ＤＲＹ → ＡＵＴＯ → ＦＡＮ
3 "FAN "
When the unit is running in the "FAN", "COOL" mode there are 3 kinds of fan speed could
be selected, press "FAN " to choose between "LOW → MD → HIGH".
4." TEMP"
When turn on the air conditioner, in the "COOL", mode, the control panel will display the set
temp. Press "▲"""to increase or to decrease the set temperature.
5. " TIMER"
Press"▲""" to set the time for timer on or timer off. When the unit is running, you could set the
timer off, the unit will stop running; When the unit is stop running (not power off ) set the timer on, the
time interval being set will be 0.5-24 hour(s), press "▲""" to adjust.
6. " SLEEP"
When the unit is running, press once to set "SLEEP" operation, repress it, the unit will stop the "SLEEP"
operation, there is no "SLEEP" operation in "AUTO" mode.
7. " HEAT"
Pressthe"mode"button,selecttheheatingmode,theLCDwindowshows" ".

－8－
OPERATING METHODS
1). To select a place near the door and window, install the exhaust duct put the exhaust
ductout of the door, do not close the door andwindowtightly,leavingthespacefor
air flow, for example to open the window or the door, to keep the good ventilation.
2). Press "MODE" to select "COOL" mode.
3). Press "TEMP" to set the suitable temp.16℃-30℃.
4). Press "FAN" to select the suitable fan speed, (HIGH, MD, LOW).
When the unit is running in the COOL mode, in order to keep the good cooling effect,
please pay more attention to:
①If there is the direct sunlight near the window, please use the curtain to shield .
② Do not use other heat sources in the air conditioner room.
Please close the door and window, in order to obtain the better dehumidifying effect:
Press"MODE",selectthe"DRY"mode,theunitwillruninthe"DRY"mode,atthe
same time, the upper motor is running at the low speed, it is not adjustable.
When the air conditioner is used as the dehumidifier, it is no need to install the exhaust duct.
1). Press "MODE", to select the "FAN" mode.
2). Press "FAN ", to choose from the HIGH, MD, LOW fan speed options.
Press"MODE"toselectthe"AUTO"mode,themicrocomputerprocesswill
automaticallychoosetheCOOL,DRY mode,toensuretheindoorconstant
temperature efficiency.
COOL
CAUTION
DRY
CAUTION
FAN
AUTO
WATER
DRAINAGE
When in "COOL" or "DRY" mode, the dew water will drain into the tank, when the tank gets
full, the buzzer will sound "Di, Di……"for eight times, LCD window shows error code "E4",
at the same time the unit will switch off, till there is no full of water, and the compressor will
stop for 3 minutes to restart, pull out the plug of the drainage pipe, take out the drainage pipe
from the set clamp, pour out the water inside the tank, then insert the plug to the drainage pipe,
in order to avoid the leakage, at the same time fix the drainage pipe on the set clamp, it is shown
as below:
Rear plate
Fix the drainage pipe on the set clamp
Drainage pipe
Pressthe"mode"button,selecttheheatingmode,theLCDwindowshows" ".
HEATING

●Make sure to aim the signal port of remote
controller at the signal receiver indicator of front
panel.
Onlythe AUTO,ON/OFF,SLEEP,SEND
couldbeusedtosendthecurrentdisplayoperation,
theother could be used to change the mode.
The other functions please refer to the cooling
only type air conditioner
SLEEP
PressthistosetSLEEPoperation,
andpressthe"Hr"toadjustthetime
of timer off (it can be choose from 1-7
hours),whenrepress,theoperation
will stop.
ON/OFF
Press once to start and press once more
to stop the unit.
DRY
SEND
Press this key to send the operation, the
screen will show the operation.
Pressthis,theairconditionerwill run in
DRYmode.
ON/OFF
HIGH
TIME
AM
MODE
FAN
TIMER
DRY
Hr
SLEEP
Min
LCD Ddisplay
It shows all set contents
－9－
NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER
SEND

－10－
●In case of the power off during the operation, all options will be
ceased.
●Ifneedtoresumetheoperation,pleaserepressthe"SEND".If
there is the malfunction in the operation procedure, or due to the
thunder, cause the wrong operation, please pull out the power plug,
and reinsert it, then press the "SEND".
POWER OFF
ON/OFF
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
NAMES AND FUNCTIONS OF THE REMOTE CONTROLLER
MODE
Pressthe"MODE"stepbystep,the
LCD will display the COOL-FAN-HEAT-
AUTO mode, circularly.
TEMP
Press once, the SET TEMP. will decrease
1℃. Press once, the SET TEMP. will
increase 1℃. The SET TEMP. can be
selected from 16℃-30℃, the utmost temp
are 16℃and 30℃.
FAN
The switchover of FAN mode are HIGH-
MD-LOW.
TIMER
PressthetoselecttheSETTIMERmodeorthe
TIMEmode,Whenselectthe"SETTIMER"
mode, the LCD will display the time of the SET
TIMER mode, while select the "TIME" mode,
the LCD will display the current time.
Hr/Min
When the unit is running in the "TIME" mode,
press "Hr" once, the number will increase 1,
press "Min" once, the number will increase 1.
When the unit is running in the "SET TIMER"
mode, press the key once between 0-7, the
numberoftimewillincrease0.5,presstheonce
above8,thenumberoftimewillincrease1.
Whentheunitisrunningin"SLEEP"mode,
pressthe"Hr"once,thetimeintervalwill
increase 1 hour, and will circulate from 1 to 7
hour(s).

－11－
COOLMODE OPERATION
COOL
●When temperature of room sensor is higher
than the set temp, compressor runs, the unit starts
cooling operation.
●When temperature of room sensor is lower
than the set temp, compressor stops, the unit runs
in "FAN" mode.
●The set temp should be in range of 16℃~30℃.
ON/OFF
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
１８ Ｃ
０
1.After inserting the batteries, press
"ON/OFF" to start the unit.
2. Press "MODE", to choose "COOL"
mode.
3. Press "FAN" , to set fan speed.
4. Press "TEMP" , to set the desired
temp.
5. Press "SEND", send the operation
to the unit.

－12－
HEAT MODE OPERATION (only for cooling/heating type units)
●When the air conditioner was disturbed, the
remote controller can't work once in a while,
only to pull out the power plug, after reinserting
it, it can be operated.
●Is the voltage of the batteries full or not,
otherwise to replace the worn batteries.
● When the LCD of the remote controller
couldn't display the all set contents clearly, or
the set options couldn't be received, please
replace the batteries.
The compressor and lower motor stop running,
only PTC is running, the upper motor is running
at the set fan speed.
HEAT
ON/OFF
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
1. After inserting the batteries, press
"ON/OFF" to start the unit.
2. Press "MODE" , to choose "HEAT"
mode.
3. Press "TEMP" , to set the desired
temp.
4. Press "FAN", to set fan speed.
5. Press "SEND", send the operation
to the unit.

ON/OFF
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
１８ Ｃ
０
5.Press "SEND" , send the operation
to the unit.
1.After inserting the batteries, press
"ON/OFF" to start the unit.
2.Press "DRY" , to set "DRY" mode,
when repress dry, it will run in original
operation.
3.Press "TEMP", to set desired temp.
4.Press "FAN" , to set fan speed.
When the unit is in DRY mode, the compressor
is protecting, the fan motor runs at low fan speed.
DRY
－13－
DRY MODE OPERATION

－14－
SLEEP MODE OPERATION
● When the unit is running in SLEEP mode, press "Hr"
to set timer on, the interval is (1-7 hours.)
● When the unit is running in SLEEP mode, according to
the time changes, it could adjust the original set temp
automatically, in order to save energy and make a
comfortable sleeping.
1. After inserting the batteries, press
"ON/OFF" to start the unit.
2. Press "MODE" , to select the
operation mode.
3. Press "TEMP" , to set desired
temp.
4. Press "FAN" to set fan speed.
5. Press "SEND", send the operation
to the unit.
6. Press "SLEEP" , to set SLEEP
operation, when press once more it
will stop.
ON/OFF
HIGH
TIME
AM
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
１８ Ｃ
０
ＳＬＥＥＰ

1. After inserting the batteries, press
"ONOFF" to start the unit.
2. Press "MODE" , select "AUTO"
mode, according to the room temp, the
microcomputer will adjust the turn on
or turn off of the compressor and fan
motor, automatically. In order to obtain
comfortable effect.
3. Press "SEND" , send the operation to
the unit.
ON/OFF
HIGH
TIMER
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min
● According to the room temp, the microcomputer will
adjust the turn on or turn off of the compressor, automatically.
In order to obtain comfortable effect.
AUTO MODE
－15－
AUTO MODE OPERATION

－16－
TIMER MODE OPERATION
1. When the unit is running, press
"TIMER" , to set the TIMER operation.
2.Press"Hr/Min",tosettheTIMER
ON, it can be selected in the range of
1-18 hours.
3. Press "SEND" , send the operation to
the unit.
tosettheTIMEROFF,itcouldbe
selectedintherangeof1-7hours.
4.Press"SLEEP",thenpressthe"Hr/Min",
●After the SET TIMER ON, the unit turns off at once, when the set
time arrived, the unit will run in the original mode.
●Press "TIMER" , to select "TIME", the screen will display the
current time, press "Hr/Min" to adjust the number of current hour or
minute.
●When pressing the "SLEEP" to set the "SLEEP" mode, the "SET
TIMER" mode will be canceled, when selecting the "SET TIMER"
mode, the "SET SLEEP" mode will be canceled.
ON/OFF
HIGH
TIMER
MODE
FAN
SEND
TIMER
DRY
Hr
SLEEP
Min

1. The installation method for castor:
avoid the unit damage.
5 , in order to
Note: It must be installed the castors before operating the unit, or it will cause the inconvenient
move or even a damage. When install the castors, the gradient should be less than
1). Open the accessory bag, take out the castors (4).
2). Raising up the unit horizontally, 10-20cm away from the ground.
3). Screw the castors into the slot of the chassis. The installation procedure is shown as follow:
2 The installation method for drainage pipe:
Note: It must be installed the drainage pipe before operating the unit, or it can cause the drainage block
and will influence the unit running.
1). Take out the drainage pipe (including the drainage hole cap and clamp) from the accessory bag. Install
the drainage pipe to the drainage hole of the chassis, make sure to insert the drainage pipe to the bottom of the
outlet.
2). After inserting the drainage pipe, fix it on the clamp of the rear plate, it is shown as follow:
Castor
Drainage pipe
After inserting the
drainage pipe, fix it
on the set clamp of
the rear plate
Drainage hole
Clamp
－17－
Slot
Rear plate
INSTALLATION GUIDE FOR CASTOR, DRAINAGE PIPE AND AIR EXHAUST ACCESSORY

－18－
3. The installation method for accessory of the exhaust duct:
INSTALLATION GUIDE FOR CASTOR, DRAINAGE PIPE AND AIR EXHAUST ACCESSORY
1). Fix the end of the exhaust duct to the exhaust terminal of the unit.
2). Put the other end (discharge) to the nearest window.
Please pay more attention to the length of the exhaust duct is 500mm-
2000mm, it is advisable to use the minimal length to install.
！
CAUTION
When fixing the exhaust duct, try to keep the exhaust duct horizontal and
do not extend the length optionally or connect with other exhaust duct, or
it can cause the abnormal operation to the unit.
130cm
40cm
Correct installation is shown below (If mounting in the wall, the height
of the hole should be 40cm-130cm)