Green Bike Electric Motion Enduro 48 User manual
Instruction Manual
Dear Client,
Green Bike –Electric Motion Congratulations on you're newly purchased
Joining Green bike's Go Green revolution will open your doors to a whole
new world of freedom! Green Bike –Electric Motion LLC greatly values the
quality of our products, giving you value for your money, friendly and
professional service, and safety for the rider above all else.
Please uphold the product-customer-importer relationship to ensure a
quality experience over time. In this manual, you will find all the details
required to maintain product care.
To ensure safety during riding and to maintain long-term usage experience,
please read all instructions carefully before using the bike, and follow the
specified maintenance and usage instructions.
Thank you for choosing Green Bike –Electric Motion!
Picture of the location of bicycle parts:
•For your safety, obey traffic and signage instructions.
•Do not put additional people on the bike. The bike are intended to carry only one
person.
•The height of the chair and handlebar should be adjusted for maximum comfort
and control.
•In the seat post and handlebars there is a safety strip. Make sure it is not visible
when adjusting. If the safety strip is visible the seat post/handlebars grip is not
fixed.
1. Throttle 2. Grips. 3. Handlebar. 4. Brake handle. 5. Brake cable. 6. Stem 7. Front fork 8.
Front wheel. 9. Tire and inner tube. 10. Front brake. 11. Controller. 12. Pedal. 13. Front
wheel chain (crank). 14. Pedal assist unit. 15. Chain shield 16.Kickstandl. 17. Motor cable. 18.
Chain. 19. Motor. 20. Rear derailleur. 21. Rear derailleur cable. 22. Rear brake. 23. Rear light. 24.
Seatpost. 25. Saddle. 26. Seatpost quick release. 27. Rear shock absorber. 28. Lithium battery. 29.
Frame
•Be sure that the adjustment locking handles of the seatpost are in lock mode
before starting the trip.
•Check the condition of the brakes regularly and fine-tune the brakes when
necessary.
•Braking range on a dry road is 13 feet and on a wet road can reach to 45 feet. Keep
braking range according to the road conditions and if the road is wet keep a
greater braking range.
•The chain is properly adjusted and therefore no changes should be made. Be sure
to lubricate the chain to prevent accelerated erosion.
•At nightfall, the front and back lights must be turned on by a switch. The flashlight
and the wheels are equipped with rear light reflectors according to the standard
requirement.
•Do not wear clothing and carry luggage or bags that can be caught in the wheels or
chain, do not ride with high heels or clothing that is not suitable for cycling to keep
the rider safe. Also, do not put your legs to close to the chain or wheels more than
necessary.
•Do not ride in weather that does not allow safe riding such as rain, puddles, fierce
winds etc.
•When stopping, use both brakes. The front and the rear too, do not rely on one
brake. In order to maintain stability and achieve greater control.
•Do not ride under the influence of alcohol, drugs or medication that affect the
rider's awareness.
•During the ride, hold the two handles, do not perform stunts and do not make
reckless turns without examining the area on all sides before making the call. Local
regulations must be followed.
•Do not drop the bike on the ground due to the sensitivity of the battery, motor and
controller. They should be placed on the jack carefully.
Before starting the ride
•Insert the battery into place with an angle and lock it.
•Fold the side jack and sit on the chair, one foot on the pedal and the other on the
ground.
•Now start pedaling and the engine will start running.
•Indicator: During the ride the battery will be discharged according to use and the
battery meter will see its status in 5 bars on the digital display.
When the fifth and final markings flash, the switch must be closed and pedaled as
a regular bicycle.
After recharging, you can drive again with the electric motor.
•Park in a safe place that is not an obstacle to vehicles or pedestrians. Place the bike
on the jack, disconnect the power with the main switch and pull the key out of the
lock.
•To prevent theft, it is recommended to lock the bike in a massive lock. it is
recommended to lock the chassis with the rear wheel and take the battery.
Charging:
•The battery must be charged only with the charger supplied with the bike. A
lithium battery is charged only by a Charger designed to charge lithium batteries
and not by a standard charger.
Charging with a different charger will damage the battery and will revoke the
warranty on the battery.
Do not open the battery or charger for testing! Inspection shall be done only by an
authorized laboratory on our behalf or in the importer's laboratory.
The charger is designed for 110 volts. Do not use it in countries where the voltage
is different.
•Charging takes between 4-6 hours depending on battery status. The battery can be
charged outside the bicycle but also on the bike.
•The charging cable must first be connected to the battery and then to an electrical
outlet.
•When the indicator light is red, charging is performed.
When charging directly on the bike, make sure the main switch is off.
When the indicator light turns green, the battery is full and must be disconnected
from the power source.
When charging, the battery must be properly positioned and not fall or damaged.
•When the battery life is over, the battery should not be discarded but drop in a
recycling point for lithium batteries KEEP OUR WORLD GREEN.
•Before beginning the ride, check that all the indicator lights are working and the
battery is locked in place.
•Check that the electrical contacts of the battery are always clean. Clean with a dry
cloth without moisture.
•Check regularly tire pressure. The correct pressure is 50 PSI in the rear wheel and
45 PSI in the front wheel depends on the weight of the rider. Improper pressure
will also cause the battery to overuse and shorten the cycling time.
•Do not drive in puddles. If water enters the engine, the controller or the battery
house, these parts may be damage or get short circuit.
Water travel will void the warranty provided by the manufacturer.
The bike must be stored in a dry place. Overly humidity causes corrosion in the
electrical parts. Do not leave the bike in the rain.
•Do not put the bike in the beating sun, especially if you leave the battery installed
on the bike.
•Do not disassemble the electrical parts. Disassembling them independently will
void the warranty provided by the manufacturer.
•Do not lubricate the electrical.
Brake maintenance:
•The brakes in this model are high-quality hydraulic disc brakes designed by Green
Bike Electric Motion
The left stop handle is responsible for braking the front wheel and the right stop
handle is responsible for braking the rear wheel.
•Always check if the brakes are intact and are optimally tuned.
•If the brakes is not tuned and unnecessarily touches the wheel while driving, the
power of the battery would be wasted in vain and the brake will wear out.
•Be sure to replace the brake pads before they are finished, because in such a
situation metal touches the metal, the braking ability is damaged and the brake
system is damaged.
Bicycle cleaning
•For maximum performance of the bike, it is recommended clean them of sand and
mud. If you cannot clean the entire bike, you must clean at least the propulsion
system (chain, front and rear gears).
•Cleaning frequency: once every three or four propound rides or after every ride
where the bike gets dirty.
•You must have a bucket with water, soluble fats, a kitchen swab for washing
dishes, rags, and a special brush with hard fibers.
•Never wet the electrical parts. Wet part can short circuit and will void the warranty
provided by the manufacturer.
•Washing: wash all parts of the bike (except of the electrical system parts) using a
sponge. The hard brush is for removal heavy dirt from the gears, pedals, etc.
•Drying: Dry the bike with the rags and place them in direct sunlight until full drying
(preferably not washed at night or in stormy weather). Immediately after washing
and drying, lubricate the chain. The brakes are recommended to be cleaned with a
specialized material for it.
•When cleaning, be careful not to wet the electrical parts and cables. Do not spray
on battery, controller, monitor and any wiring system, so do not use running water
/ hose.
KH-DX-M1 : Ebike Display with thumb throttle
Material
Caser and Cover: ABS
LCD window: PMMA
Overview
1. Manipulation:
Integrated with one thumb throttle for speed regulation
Equippedwith3pressbuttons
toswitchdisplaycontentandmake
parameter settings
2. Protocol:
ThisdisplayusesUARTprotocol,throttlesignalissentby UART tocontroller
3. Speed：
Real-time SPEED
，
MAX SPEED
，
Average SPEED
4. Battery level:
Indicates the battery level in real time
5. Light control:
ON/OFF : Press button for 3 seconds to switch on/off
6. Assist level:
From 1 to 3, press up or down button to change assist level (could be set to more
levels)
7. Distance:
ODO/Trip/Ride time
8. Error code:
Please refer to appendix table 1 for definition
9. 6km/h mode:
In this mode, it will display on the screen.
10.Parameters setting:
Set parameters, such as: wheel size, speed limit etc.
Presentation of screen
Battery level: 5 levels,
Speed: Average SPEED/MAX SPEED/Real-time SPEED
Speed unit: KMH/MPH
6km/h walk mode:
Assist level: assist level 1~3.
Head light icon: shows up when head light and back light are on.
Distance: Trip/ODO.
Error code: “ERR” and code show up when there is error.
Operation instructions
It is equipped with 3 press buttons:
“UP” “Power” “DOWN”
1. Power ON/OFF
When the power is off, Long press （Power）during 3 Seconds, screen
will display all contents and start to normal
working mode. When the power is on, Long press （Power）during 3
seconds, screen will be powered off. If no any operation both on bike and display
during 10 minutes (time could be set), the display will turn off automatically, in this
case, no power consumption for both display and controller.
2. Different Speed display:
Long press and Power switch different speed
information, Real time speed (SPEED) → Max speed（MAX SPEED）→Average
speed (AVGSPEED)
3. ODO/TRIP/ Ride time/Error Code
Short press to switch ODO/TRIP/Ride time/Error Code Trip (Single trip
distance)→ODO (Accumulated distance)→TM (Ride time)→ERR (Error Code)
4. Assist level
Short press
or
to change assist level, default valueis
level1
5. Lightcontrol
Longpress
for3secondsturnon/offtheheadlightandrear lamp
6. 6km/h mode
Whenthebikeisstopped,longpress
,willenter6km/hmode,
thespeedwillbe
4.5~7.5km/haccordingtodifferentroadconditions,
will show up on screen, long
press again or short press to quit 6km/h mode. Long press or short press
could be customized by clients.
Parameterssetting
When the display is powered on, long press
a
nd
, will enter parameter
setting mode, in this mode, user can change parameter values.
long press again
and
will quit
parametersettingmodeornooperationduring10swillalso
quitthis
mode.
In parameter setting mode, short press /
will
changeparametervalue, short
press
willsavecurrent
valueand switch to nextparameter.
•P01-back lightlightness:
short press
/
willswitchfrom 1 to 3, Level 3 is lightest. Level 2 is
default value
Picture 14
•P02-KMH / MPH:
Short press
/
to SwitchKmh/MPH.
•P03-Battery ratedvoltage:
Short press
/
toswitch24V, 36V,48V,Defaultvalue
is 36V.
•P04-Auto shutdowntime:
short press
/
to switch from 0 to 60, it is the time (in minutes) to shut
down the screen automatically if no operation, 0 meansnevershutdown,Default
valueis10minutes
•P05-Number of Assistlevels:
Short press
/
to change level 0->1->2.
assistlevels :
0: 3 assistlevels
1: 5 assist levels
2: 9 assist levels
•P06-Wheel size selection:
short press / to switch wheel size, in inch, step: 0.1 inch
•P07-Number of magnets for speed sensor:
short press / to switch from 1 to 100.
•P08-speed limit:
short press / to set the speed limit from 0 to 100Km/h, 100 means no
limit. In this e-bikes the controller is limited to 20 mph with throttle because the
USA regulations.
•P09-Non-zero speed start:
short press / to switch from 0 to 1.
0: zero speed start, (you can use the electric assist start from 0 mph.)
1: non-zero speed start.
Importer recommendation : In order to extend the battery life time, it is
recommended to start the trip with a mechanical pedal and then switch to the
electric assist and not to start from 0
•P10-Driving mode selection:
14
short press / to switch from 0->1->2.
0：Assist mode (throttle does not work, only pedal assist);
1: Electrical driving mode(only throttle works, pedal assist does not work)
2: Both assist and Electrical driving mode (Not available if in zero speed
start and electrical driving mode
•P11-assist sensitivity setting:
short press / to switch from 1 to 24.
•P12-assist starting power setting:
short press / to switch from 0 to 5.
•P13-Assist magnetic disc types:
short press / to switch from 5->8->12 ，different numbers of
magnets in the disc.
•P15-low voltage protection for controller :
•P16-Reset ODO distance:
long press during 5 seconds.
•P18-Reset all parameters:
long press 5 seconds, when it displays “SSSS”, all parameters reset to
default values (except for the ODO distance).
0
Specifications
Power supply: 24V,36V, 48V
Rated current: 10mA
Max current: 30mA
Leakage current after power off: <1uA
Current supply to controller: 50mA
Working Temperature：-18~65℃
Storage temperature：-30~80℃
Notices
Power on and power off must keep an interval of at least 3 seconds,
Please don’t press ” button frequently when it is powered off. When the
temperature is under -10℃, the screen will be a little darker than normal, when the
temperature increases, the screen can go back to normal
Warranty
1 year of warranty for quality issue except outside case is broken.
Table of contents
Other Green Bike Electric Motion Bicycle manuals
