Greenheck SSDFD-155 User manual

Model SSDFD-155 meets the requirements for fire dampers
established by:
National Fire Protection Association
(NFPA Standards 80, 90A & 101)
Underwriters Laboratories Standard 555 (Listing #R-13317)
BOCA National Building Codes
IBC International Building Codes
ICBO Uniform Building Codes
SBCCI Standard Building Codes
New York City (MEA listing #260-91-M)
California State Fire Marshall
(Listing #3225-981:102)
Model SSDFD-155
Dynamic Rated Fire Dampers
11/2Hour Fire Resistance Rating
100% Free Area - Sealed for High Pressure Systems
APPLICATION
Model SSDFD-155 is approved for use in walls, floors and
partitions with fire resistance ratings less than 3 hours.
This model carries a 11/2hour UL fire damper label. UL
555 classifies dynamic rated fire dampers for use in HVAC
systems that are operational in the event of fire .
RATINGS
UL555 Fire Resistance Rating
Fire Rating: 1 1/2 hours
Dynamic closure rating
Maximum Velocity: 2000 fpm (10.2 m/s) vertical mount
Maximum Pressure: 4 in. wg (1 kPa)
CONSTRUCTION
Stainless steel (in gauges required by UL listing R-13317)
INSTALLATION
All fire damper installations require the use of sleeves,
angles and methods described in Greenheck Fire Damper
Installation Instructions #452763, included with every
damper shipment. Sleeves can be field fabricated or
factory furnished as a complete damper/sleeve assembly.
See Factory Sleeve Option below for details.
FEATURES
• Stainless steel closure springs
• Fusible links (165ºF (74ºC) standard, 212ºF (100ºC)
available.
• Vertical or horizontal mount available
OPTIONAL FEATURES
• Sealed transitions and sleeves
• Security bars
• One piece retaining angles (POC)
• Transitions (C, CO, CR, R)
3
11
/ 16 in.
W*
H*
(94mm)
FACTORY SLEEVE OPTION
SSDFD-155 Fire Dampers are available in factory furnished sleeves.
Sleeves are galvanized steel and are available in 10 thru 20 ga.
(1mm- 3.5mm) thicknesses and lengths up to 36 in. (914mm).
“K” dimension specifies location of damper within the sleeve.
Minimum is 4 in. (102mm), maximum is “L” less 4 in. (102mm),
which allows for mounting angle installation and duct connection at
each end of the sleeve. If “K” dimension is not specified, it will be
provided as one half of “L” dimension (damper centered in sleeve).
Note: If using access doors, the door should be installed on the “K”
side of the damper.
* These dimensions are furnished approximately 1/4in. (6mm) undersize.
H*
K
Damper
Location
L
Overall Sleeve Length
W*
C
LDamper Frame
Sleeve
Damper
Vertical mount
“UL CLASSIFIED (see complete marking on product)”
“UL CLASSIFIED to Canadian safety standards (see
complete marking on product)”
Standard 555 (Listing #R13317)

SSDFD-155 Type CR, CO, C, & R
The following chart show minimum and maximum damper size.
Dimensions are in inches (mm in parentheses).
O*
H*
Type C
W*+2
W*
O*
H*
Type CO
W*+2
W*
D*
Type CR
O*
D*+2
Copyright © 2006 Greenheck Fan Corporation
SSDFD-155 Rev. 2 July 2006
Overall Damper Dimensions
2 Multi-Section Limitations
Maximum damper height is 44" when combination width is 94" or less.
Maximum Single Section
Dimensions
Multi-Section Limitations
Maximum transition height is 36" when transition width is greater than 94" and less than or equal to 118".
3
Type COType C
36”
Max.
118”
Max.
118”
Max.
36”
Max.
94” Max.
or 72” Max.
25 in. (635mm)
Max.
25 in. (635mm)
Max.
28 in.
(711mm)
Max.
28 in.
(711mm)
Max.
Multi-Section Limitations
Maximum damper height is 69" when combination width is 72" or less. (Vertical mullion provided on dampers over 34”
wide and 44” high.)
44” Max.
or 69” Max.
94” Max.
or 72” Max.
44” Max.
or 69” Max.
4
2
4
2
4
2
4
2
4
Reinforcement
Rods
25 in.
(635mm)
Max.
29 in.
(737mm) max.
inches (mm)
Type CR Type CO & C Type R*1
Minimum Maximum Minimum Maximum Minimum Maximum
Single section
Vertical
3
(76)
25
(635)
3 x 3
(76 x 76)
28 x 25
(711 x 635)
3
(76)
29
(737)
C, CO, CR transitions
are positioned 1
in.(25mm) from bottom
of sleeve.
*1 With 2 in. (50mm) offset. Sizes adjust with 0 offset & 1 in. (25mm) offset.
Size Limitations
Type CR Type R
Type R transition is centered on damper
frame. Dimensions are with 2 in. (50mm)
offset.
H* or D* O*
3 (76) 6 (152)
4 (102) 7 (178)
5 (127) 8 (203)
6 (152) 9 (229)
7 (178) 10 (254)
8 (203) 11 (279)
9 (229) 12 (305)
10 (254) 13 (330)
11 (279) 14 (356)
12 (305) 15 (381)
13 (330) 16 (406)
14 (356) 17 (432)
15 (381) 19 (483)
16 (406) 20 (508)
17 (432) 21 (533)
18 (457) 22 (559)
19 (483) 23 (584)
20 (508) 24 (610)
21 (533) 25 (635)
22 (559) 27 (686)
23 (584) 28 (711)
24 (610) 29 (737)
25 (635) 30 (762)
* Dimensions are in inches (mm). These
dimensions are furnished approximately
1/4 in. (6mm) undersize.