Greenheck Multi-blade Fire Damper DFD-M210 User manual

Application
Model DFD-M210 is a multi-blade fire damper with 3V style blades.
The DFD-M210 has been qualified to 10.2 m/s (2000 fpm) and 1.0kPa
(4 in. wg.) for operation and dynamic closure in emergency fire
situations. Model DFD-M210 may be installed vertically (with blades
running horizontal) or horizontally and is rated for airflow in either
direction.
Model DFD-M210 has also been tested in accordance with BS476 to
4 hours at Warrrington Fire, UK, and is approved for fire partitions of 4
hours or less where British Standards are required.
Ratings
UL 555 Fire Resistance Rating
Fire Rating: 11⁄2Hours
Dynamic Closure Rating: Actual limits are size dependent
Maximum Velocity: 10.2 m/s (2000 fpm)
Maximum Pressure: 1 kPa (4 in. wg)
BS476 Fire Resistance Rating
Fire Rating: 4 hours
Standard Construction
Frame: 127mm x 25 mm (5 in. x 1 in.) 1.5mm
(16 gauge) galvanized steel hat
channel with reinforced corners. A
low profile head and sill are used on
sizes less than 432mm (17 in.) high to
maximize free area and performance.
Blades: 1.5mm (16 gauge) galvanized steel,
reinforced with 3 longitudinal
structurally designed vee’s.
Seals: Flexible stainless steel jamb seals.
Linkage: Concealed in jamb.
Fusible Link: UL listed 74ºC (165°F)
Axles: 13mm (1⁄2 in.) dia. plated steel.
Bearings: Bronze sleeve type.
Actuator: Manual quadrant.
Size Limitations
Minimum Size: 203mm W x 152mm H
(8 in. W x 6 in. H)
Maximum Size:
Single Section: 914mm W x 914mm H
(36 in. W x 36 in. H) or
813mm W x 1270mm H
(32 in. W x 50 in. H)
Multi Section: 1626mm W x 1270mm H
(64 in. W x 50 in. H)
Optional Features
•100ºC (212°F), 141ºC (286°F), and 177ºC (350°F) fusible links (UL only)
• 69°C (155°F) fusible links (BS476)
• Factory mounted sleeves
• Retaining angles
• Sleeve with integral flange on both sides
Model DFD-M210
Multi-Blade FIRE DAMPER
Steel 3V Blades
UL555 11/2Hour Fire Resistance Rating
4 hour Fire Resistance Rating (BS476)
* W & H dimensions furnished approximately 6mm (1/4 in.) undersize.
(Add sleeve thickness for overall sleeved damper dimension)
H
W
LH
RH
“UL CLASSIFIED (see complete marking on
product)”
“UL CLASSIFIED to Canadian safety standards
(see complete marking on product)”
Standard 555 (Listing #R13317)
Model DFD-M210 is intended for installation in
accordance with fire damper requirements
established by:
National Fire Protection Association
NFPA Standards 80, 90A & 101
ICBO Uniform Building Codes
IBC International Building Codes
SBCCI Standard Building Codes
British Standard BS476
Tested to 4 hours at Warrington Fire, UK
R
Greenheck Kunshan Co. Ltd. and Greenheck Fan
Corporation certifies that the model DFD-M210
shown herein is licensed to bear the AMCA
Seal. The ratings shown are based on tests and
procedures performed in accordance with AMCA
Publication 511 and comply with the requirements
of the AMCA Certified Ratings Programs. The
AMCA Certified Ratings Seal applies to air
performance ratings only.

Pressure Drop Data DFD-M210
This pressure drop testing was conducted in accordance with AMCA Standard 500-D using the three configurations shown. All
data has been corrected to represent standard air at a density of 1.201 kg/m3.
Actual pressure drop found in any HVAC system is a combination of many factors. This pressure drop information along with an
analysis of other system influences should be used to estimate actual pressure losses for a damper installed in a given HVAC
system.
AMCA Test Figures
Figure 5.3 Illustrates a fully ducted damper. This configuration has the lowest pressure drop of the three test configurations
because entrance and exit losses are minimized by straight duct runs upstream and downstream of the damper.
Figure 5.2 Illustrates a ducted damper exhausting air into an open area. This configuration has a lower pressure drop than
Figure 5.5 because entrance losses are minimized by a straight duct run upstream of the damper.
Figure 5.5 Illustrates a plenum mounted damper. This configuration has the highest pressure drop because of extremely high
entrance and exit losses due to the sudden changes of area in the system.
5D 6D
5D
D4 (W) (H)
3.14

AMCA 5.2 Pressure Drop DFD-M210
5D 6D
5D
D=4 (W) (H)
3.14
Figure 5.3
Figure 5.2
Figure 5. 5
R
Greenheck Kunshan Co. Ltd. and Greenheck Fan
Corporation certifies that the model DFD-M210
shown herein is licensed to bear the AMCA Seal. The
ratings shown are based on tests and procedures
performed in accordance with AMCA Publication
511 and comply with the requirements of the AMCA
Certified Ratings Programs. The AMCA Certified
Ratings Seal applies to air performance ratings only.
   



 NNYNN
 NNYNN
 NNYNN
 NNYNN
 NNYNN
13&4463&%3011"4$"-4
'"$&7&-0$*5:.&5&344&$0/%
".$"
7&-0$*5:7413&4463&%301
Y
Y
Y
Y
Y
305mm x 305mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 10
5.1 35
7.7 80
10 135
12.6 207
15.5 311
17.8 411
20.8 561
610mm x 610mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 5
5.2 17
7.8 42
10.3 72
12.9 115
15.4 162
18.1 224
20.8 296
914mm x 914mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.6 3
5.1 10
7.6 22
10.2 42
12.7 65
15.3 95
17.7 127
20.3 167
305mm x 1219mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 3
5.1 15
7.6 32
10.3 57
12.9 90
15.3 125
18 174
20.5 227
1219mm x 305mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 8
5.1 27
7.7 57
10.3 105
12.9 164
15.6 242
17.9 316
20.7 424

R
Greenheck Kunshan Co. Ltd. and Greenheck Fan
Corporation certifies that the model DFD-M210
shown herein is licensed to bear the AMCA Seal. The
ratings shown are based on tests and procedures
performed in accordance with AMCA Publication
511 and comply with the requirements of the AMCA
Certified Ratings Programs. The AMCA Certified
Ratings Seal applies to air performance ratings only.
305mm x 305mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.4 5
5.1 22
7.8 52
10.3 92
12.9 145
15.4 209
17.7 274
20.8 379
610mm x 610mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 3
5 10
7.7 22
10.3 40
12.8 62
15.5 92
17.9 122
20.8 167
914mm x 914mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 3
5.1 8
7.6 15
10.1 27
12.8 42
15.3 62
17.7 82
20.3 107
305mm x 1219mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 3
5.1 10
7.7 25
10.3 42
12.9 67
15.7 100
18.7 140
20.9 174
1219mm x 305mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 5
5.1 20
7.6 40
10.1 72
12.7 112
15.3 164
18 227
20.6 299
AMCA 5.3 Pressure Drop DFD-M210
5D 6D
5D
D=4 (W) (H)
3.14
Figure 5.3
Figure 5.2
Figure 5. 5
   



 NNYNN
 NNYNN
 NNYNN
 NNYNN
 NNYNN
13&4463&%3011"4$"-4
'"$&7&-0$*5:.&5&344&$0/%
".$"
7&-0$*5:7413&4463&%301
Y
Y
Y
Y
Y

R
Greenheck Kunshan Co. Ltd. and Greenheck Fan
Corporation certifies that the model DFD-M210
shown herein is licensed to bear the AMCA Seal. The
ratings shown are based on tests and procedures
performed in accordance with AMCA Publication
511 and comply with the requirements of the AMCA
Certified Ratings Programs. The AMCA Certified
Ratings Seal applies to air performance ratings only.
305mm x 305mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 13
5 55
7.5 122
10.2 222
12.7 349
15.4 508
17.9 688
20.6 907
610mm x 610mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 8
5 35
7.6 75
10.3 140
12.8 217
15.3 309
17.7 409
20.8 568
914mm x 914mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 8
5.1 30
7.7 67
10.2 115
12.9 184
15.5 269
18.1 354
20.6 471
305mm x 1219mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.6 8
5.1 32
7.7 75
10.2 130
12.7 202
15.5 301
18.1 416
20.6 536
1219mm x 305mm
Velocity
(m/s)
Pressure
Drop (Pa)
2.5 1
5 42
7.7 95
10.3 172
12.7 264
15.3 381
17.9 521
20.8 707
AMCA 5.5 Pressure Drop DFD-M210
5D 6D
5D
D4 (W) (H)
3.14
2 5 10 30
10
100
1000
305mm x 305mm
610mm x 610mm
914mm x 914mm
305mm x 1219mm
1219mm x 305mm
PRESSURE DROP- PASCALS
FACE VELOCITY- METERS/SECOND
AMCA 5.5
VELOCITY VS. PRESSURE DROP
305 x 305
1219 x 305
610 x 610
305 x 1219
914 x 914

DIMENSIONAL DATA SPECIFICATIONS
Damper Sizing Information
The following figure shows maximum damper section size.
Single Section
Damper Sleeve Dimensional Data
The drawings below and corresponding table show the position of the DFD-M210 damper when mounted in a factory sleeve.
The standard mounting locations provide enough space for the mounting of manual quadrant, controls and allow space for
installation of retaining angles and duct connections.
127mm
Right hand drive is shown
Left hand drive available upon request
LH RH
A
Sleeve Length
Varies
B*
S
T*
152mm
38mm max.
95mm
137mm
The “A” dimension is the location of the damper mounted in a
factory sleeve. The table below shows the Standard, Minimum,
and Maximum “A” dimensions.
Specifications
Fire Dampers meeting the following specifications shall be furnished and
installed where shown on plans and/or as described in schedules. Dampers shall
meet the requirements of the latest edition of NFPA 80, 90A and 101.
Dampers shall be tested, rated and labeled in accordance with the latest edition
of UL Standard 555. Dampers shall have a UL 555 fire rating of 11⁄2hours. Each
damper shall be equipped with a heat responsive device which has been tested
and approved for use with the damper assembly in accordance with UL 555.
The heat responsive device shall have a temperature rating of (specifier select
one of the following) 74ºC, 100ºC, 141ºC, or 177ºC. Dampers shall be UL labeled
for use in dynamic systems. The damper shall have a dynamic closure pressure
rating of 1 kPa.
Damper actuator shall be manual quadrant. Manufacturers submittal data shall
indicate actuator space requirements around the damper.
The Damper Manufacturers submittal data shall certify all air performance
pressure drop data is licensed in accordance with the AMCA Certified Ratings
Program for Test Figures 5.2, 5.3 and 5.5. Damper air performance data shall be
developed in accordance with the latest edition of AMCA Standard 500-D.
Damper blades shall be 1.5mm galvanized steel 3V type with three longitudinal
grooves for reinforcement. Blades shall be completely symmetrical relative to
their axle pivot point, presenting identical resistance to airflow and operation in
either direction through the damper (blades that are non-symmetrical relative to
their axle pivot point or utilize blade stops larger than 13mm are unacceptable).
Damper frame shall be 16 gauge galvanized steel formed into a structural hat
channel shape with reinforced corners. Bearings shall be sintered bronze,
permanently lubricated, synthetic (acetal) sleeve type rotating in extruded holes
in the damper frame for maximum service. Axles shall be square and positively
locked into the damper blade. Jamb seals shall be stainless steel compression
type.
Basis of design is Greenheck Model DFD-M210.
Copyright © 2005 Greenheck Fan Corpation
DFD-M210 Rev. 3 June 2005
1All dampers w/o OCI.
Note: Entire damper frame is not required to be installed
within the wall.
The damper blades, when closed, should be contained
in the wall.
H
w
1270mm
813mm 1626mm
914mm x 914mm
or
813mm x 1270mm
Multi Section
GREENHECK
Greenheck Kunshan Co Ltd.
17 Qunyi Minying District • Kunshan Economic &
Technical Development Zone
Kunshan, Jiangsu, China 215300
Tel: [phone] • Fax: [phone]
www.greenheck.com
"A" Dimension
Standard Minimum Maximum
All Dampers 183mm 137mm 406mm