GREENHURST Ascot 1.5 User manual

Ascot 1.5 and 2.0 metre
Oakley 1.5 and 2.0 metre

Contents:
Specifications.
Safety Advice.
Installation Fixings set Parts list.
Installation Procedure.
Operating the Awning.
Named list of component parts.
Specifications:
•Expansion bolts are provided for fixing to concrete and masonry walls only.
•Check carefully when fitting the awning to the brackets, that you have allowed enough clearance
between the extending arms and any opening door or windows so they do not snag or catch the
aperture.
•It is recommended the height of the awning above the aperture should be greater than 5 cm
Safety advice:
•Do not install in high windy places.
•Do not use in rainy or windy conditions.
•Use for a sun awning only.
•Be careful where you place fingers during the installation of this product.
•Please ensure all fixing are tightened at each step of the awning installation.
•Two people are required for the installation of the product.
•Do not place Awning in areas of high temperature such as on furnace walls.
•Do not place heavy items on the frame of the awning.
•Stains and bird droppings should be washed or sponged away using a mild detergent.
•We do not recommend installing this product on prefabricated structures such as caravans, static
homes and wooden buildings.
Customer Service and Helpline
Should you require further details or assistance please contact our
customer care line on 01562 753040
GABLEMERE DY11 7FB

Parts list:
Customer Service and Helpline
Should you require further details or assistance please contact our
customer care line on 01562 753040
GABLEMERE DY11 7FB

The measurements are taken from the centre of the
bracket location holes.
Using the size of the awning as a guide position the brackets in the desired location onto the wall taking care to mark
with a suitable item the fixing holes in the bracket to the wall.
Step1:
The brackets need to be a minimum of 5 cm
above the window aperture.
Using a 10mm masonry bit drill a hole approx.
70mm deep on the marks you have made for
the location of the awning.
Repeat with the second marked hole.
Using the expansion bolts tighten the bracket
with the silver hoop (gearbox) to the wall.
Follow this again for the second bracket.

Step 2:
The right hand bracket (non-eyelet) has a covered
section to be unscrewed before the awning can slide
into location on the bracket.
Place the awing into left hand bracket (eyelet)
Then slide awning into the uncovered location in
the right hand bracket (Non-eyelet)
Then retighten the cover for the right hand bracket.
Unwind the fabric for the next step.
Step 3:
Fix the extending arms into the location points in
the front bar using the 2 small screws one set for
each arm.
Step 4:
Let the support arm swing loose from the front bar.
Attach the wall clip to the support arms
Mark against the wall where the bracket meets the
wall.

Step 5:
To fix the wall clips to the wall drill an
8mm hole and tighten into place the
smaller expanding bolts.
Step 6:
To extend the Awning attach the winding
handle to the winding ring loop and turn
clockwise until fully open.
To retract the awnings turn the handle anti-
clockwise.
The winding handle can be removed when
the awning is not in use.
It is recommended that you remove the
awning from the wall during the winter
months to prolong the life of the awning.
Keep the plastic protective it was
delivered in. This will help keep it clean
while over wintering.
To retract the awning wind the fabric to
the closed position.
The arms will then move towards the wall
and rest in position until lowered again by
unwinding the awning to its desired
height.
Customer Service and Helpline
Should you require further details or
assistance please contact our
customer care line on 01562 753040
GABLEMERE DY11 7FB