Greentouch 1167FMM-26-200 Installation guide

Questions, problems, missing parts?
Before returning to your retailer,
call our customer service department at
1-855-571-1044 9 a.m. - 5 p.m., EST, Monday - Friday.
www.greentouchhome.com
Français p. 21
Español p. 42
Date Purchased _______________________
Media Mantel With 26-IN
Infrared Electric Fireplace
MODEL # 1167FMM-26-200; 1167FMM-26-201; 1167FMM-26-202
ASSEMBLY, CARE & USE INSTRUCTIONS
ITEM # 0849093;0849094;0849095
TM

2
PACKAGE CONTENTS
PART DESCRIPTION QUANTITY
A Top 1
B 1
C
Left Wall
1
D
Right Wall
1
E 1
1F
G 1
H
1I
1
Base
Side Back Panel
J
1
PART DESCRIPTION QUANTITY
N 2
O 1
1P
Q 2
R
1S
K
Insert
1
L
Remote Control
1
Left Front Door
Right Front Door
Wood Door Panel
Left Side Panel
Right Side Panel
Left Corner Panel
Right Corner Panel
1
M 2
Center Back Panel
Center Front Panel
Center Shelf
Partition
Wood Shelf
A
L
B
C
D
E
F
M
M
N
N
G
H
I
J
K
RS
O
P
Q
Q
T
Battery 2
T

3
HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)
PART DESCRIPTION QUANTITY
AA 30Long Bolt
BB Washer 30
CC Wooden Dowel 26
DD
Insert Bracket
38
EE Shelf Pin 8
FF
Back Panel Screw
2
GG Short Bolt
Touch-up Pen
6
HH Screw 4
II 1
SAFETY INFORMATION
Please read and understand this entire manual
before attempting to assemble, operate or install
the product.
This equipment has been tested and found to
comply with the limits for Class B digital devices,
pursuant to Part 15 of the FCC rules. These limits
are designed to provide reasonable protection
against harmful interference in a residential
installation. The equipment generates, uses
and can radiate radio frequency energy and, if
not installed and used in accordance with the
instructions, may cause harmful interference
to radio or television reception, which can be
determined by turning the equipment off and
on. The user is encouraged to try and correct
the interference by one or more of the following
measures:
s Reorient or relocate the receiving antenna
sIncrease the separation between the
equipment and the receiver
s Connect the equipment into an outlet on a
circuit different from that to which the receiver
is connected.
s Consult the dealer or an experienced radio/TV
technician for help.
This device complies with Part 15 of the FCC
rules. Operation is subject to the following two
conditions:
1. This device may not cause harmful
interference, and
2. This device must accept any interference
received, including interference that may
cause undesired operation.
AA BB CC DD EE IIFF
GG HH

4
Modifications not approved by the party
IMPORTANT INSTRUCTIONS
gasoline, paint or flammable vapors or liquids
are used or stored. This fireplace should not be
by the manufacturer and may cause fire,
Any repairs to this fireplace should be carried
out by a qualified service person.
Under no circumstances should this fireplace
be modified. Parts having to be removed for
SAFETY INFORMATION (CONT’D)
responsible for compliance could void user’s
authority to operate the equipment.
This Class B digital apparatus complies with
Canadian ICES-003.
When using electrical appliances, basic precau-
tions should always be followed to reduce the risk
DANGER
s If the information in this manual is not
result causing property damage, personal
injury or loss of life.
s
and LCD televisions (up to 64 inches and
weighing a maximum of 65 pounds). Using
this item with loads heavier than the stated
maximum can result in tipping and/or
instability, which can result in injury or even
death.
WARNING
sThis appliance is hot when in use. To avoid
burns, DO NOT let bare skin touch hot
surfaces. Keep combustible material, such as
furniture, pillows, bedding, papers, clothes and
curtains at least 3 feet from this appliance and
keep them away from the sides and rear.
sExtreme caution is necessary when any heater
is used by or near children or individuals with
operating and unattended.
sDO NOT run cord under carpeting. DO NOT
cover cord with throw rugs, runners, or similar
and where it will not be tripped over.
sDO NOT insert or allow foreign objects to enter
any ventilation or exhaust opening as this may
appliance.
sThis appliance has hot and arcing or sparking
parts inside. DO NOT use it in areas where
used as a drying rack for clothing. Christmas
stockings or decorations should not be hung in
the area of it.
sUse this appliance only as described in the
manual. Any other use is NOT recommended
electric shock or injury to persons.
CAUTION
sIf possible, ALWAYS unplug this appliance
when not in use.
sDO NOT operate any heater with a damaged
cord or plug or after the heater malfunctions.
DO NOT operate any heater if it has been
dropped or damaged in any manner.
Disconnect power at service panel and have
heater inspected by a reputable electrician
before reusing.
s
s
servicing must be replaced prior to operating
sDO NOT use outdoors.
sThis heater is not intended for use in
bathrooms, laundry areas and similar indoor
locations.
NEVER place heater where it may fall into a
bathtub or other water container.
sTo disconnect this appliance, turn controls to
the off position, then remove plug from outlet.
sONLY connect to properly grounded outlets.
sThis appliance, when installed, must be
electrically grounded in accordance with local
codes, with the current CSA C22.1 Canadian
Electrical Code or follow U.S.A. Installations,
follow local codes and the National Electrical
Code, ANSI/NFPA N0.70.
of fire, electric shock and injury to persons, includ-
ing the following:
followed exactly, an electric shock or fire may
This product is intended to fit most plasma
disabilities and whenever the fireplace is left
cause an electric shock or fire, or damage the
coverings. DO NOT route cord under funiture or
appliances. Arrange cord away from traffic areas
s Read all instructions before using this heater.

5
To prevent a possible fire,
Preferably, the fireplace will be on a dedicated
SAVE THESE INSTRUCTIONS
SAFETY INFORMATION (CONT’D)
A B C D
Grounding Pin Grounding Pin
Grounding Means
Metal
Screw
Cover of
Grounding
Box
Adapter
sDO NOT block
air intakes or exhaust in any manner. DO
NOT use on soft surfaces, like a bed, where
opening may become blocked.
sThe heaters
DO NOT place any object on top of the insert
or block the air intakes / vents as this can
cause the unit to overheat and could cause a
fire.
MUST NOT be located
immediately below a socket-outlet.
sALWAYS plug heaters directly into a wall
outlet/receptacle. NEVER use with an
extension cord or re-loadable power tap (outlet
/ power strip).
sDO NOT slide insert on top of wood to avoid
scratching wood surface.
s
Electrical Connection
sA 15-Amp, 120-volt, 60 Hz circuit with
a properly grounded outlet is required.
circuit as other appliances on the same circuit
may cause the circuit breaker to trip or the
fuse to blow when the heater is in operation.
The unit comes standard with 6-ft. three-wire
DO NOT exceed the current rating of the
current tap.
sThis heater is for use on 120 volt.The cord
has a plug as shown below. See illustration
for grounding instruction. An adapter as
shown at C is available for connecting
three-blade grounding type plugs to two-
slot receptacles. The green grounding
lug extending from the adapter must be
connected to a permanent ground such as
a properly grounded outlet box. The adapter
should not be used if a three-slot grounded
receptacle is available.
cord, exiting from the rear of the fireplace.
Grounding Instructions

6
Before beginning assembly of product, make
sure all parts are present. Compare parts with
package contents list and hardware contents list.
If any part is missing or damaged, do not attempt
to assemble the product.
Estimated Assembly Time: 50 minutes
Tools Required for Assembly (not included):
Phillips screwdriver
PREPARATION
ASSEMBLY INSTRUCTIONS
Hardware Used
Hardware Used
Long Bolt
Long Bolt
Washer
Washer
Wooden dowel
Wooden dowel
x 4
x 4
x 4
x 4
x 4
x 4
AA
AA
BB
BB
CC
CC
2. Insert two wooden dowels (CC) into holes on the
left of base (K). Attach left side panel (H),
securing with two washers (BB) and two long bolts
(AA).
Repeat for right side panel (I).
2
1
BB
CC
AA
K
F
1
2
1
H
BB
CC
AA
2
1. From behind the assembly, insert two wooden
dowels (CC) into holes on left outer side of base
(K). Attach Left wall (F), securing with two
washers (BB) and two long bolts (AA).
Repeat for Right wall (G).

7
ASSEMBLY INSTRUCTIONS (CONT’D)
Hardware Used
3
3.
Carefully position the center front panel (J)
into place
panel (I). Secure each side with one washer (BB)
and one long bolt (AA).
between left side panel (H) and right side
Long Bolt
Washer
Wooden dowel
x 2
x 2
x 2
AA
BB
CC
BB
CC
AA
J
1
Insert two wooden dowels (CC) into the top elddim
holes on both left side panel (H) and right side
panel (I).
4. 4
1
Hardware Used
Long Bolt
Washer
Wooden dowel
x 10
x 10
x 8
AA
BB
CC
Insert two wooden dowels (CC) into the top outer
holes on both left wall (F), left side panel (H) ,right
side panel (I) and right wall (G). Attach center
shelf (D), securing from underneath with ten
washers (BB) and long bolts (AA).
5
BB
AA
B
Hardware Used
Long Bolt
Washer
Wooden dowel
x 4
x 4
x 4
AA
BB
CC
5. Insert two wooden dowels (CC) into holes on left
side of Center shelf (D). Attach Left corner panel
(B), securing with two washers (BB) and two long
bolts (AA).
Repeat for Right corner panel (C).
B
H
2
D
BB
CC
AA
1
1
C
2
2
2

8
ASSEMBLY INSTRUCTIONS (CONT’D)
Hardware Used
Long Bolt
Washer
Wooden dowel
x 1
x 1
x 2
AA
BB
CC
6.
Hardware Used
Long Bolt
Washer
Wooden dowel
x 5
x 5
x 2
AA
BB
CC
outerpotehtotni)CC(slewodnedoowowttresnI
Insert two wooden dowels (CC) into holes on the
middle of Center shelf (D ). Attach Partition (E),
securing from underneath with one washer (BB)
and one long bolt (AA).
.7
holes of Partition (E). Attach top (A), securing from
underneath with five washers (BB) and five long
bolts (AA).
6
E
CC
1
CC
1
A
BB AA
7
Hardware Used
8
DD
2
Back Panel Screw x 18
DD
BB
AA
2
1
L
2
Attach center back panel (L) to shelving areas
using back panel screws (DD).
.8

9
ASSEMBLY INSTRUCTIONS (CONT’D)
Hardware Used
Shelf Pin x 8
EE
9
DD
Hardware Used
Back Panel Screw x 20
DD
Hold the door and align the hinge body with the
hinge plate mounted to the fireplace wall. Align
and slide the hooks/catches on the hinge body
into the recesses on the mounting plate while
lightly pushing the door towards back of
fireplace mantel. Then press on the back part
of the hinge body until you hear it click into
place. Repeat for other hinges.
To remove press the square button at the back
of the hinge body to release the hinge from the
mounting bracket. Unlock both hinges and pull
the door away from the fireplace body
NOTE: Use the pre-assembled levelers on the
base of the fireplace to level the unit. Twist the
levelers counter clockwise to increase the
height, twist the clockwise to decrease the
height.
11 .
O
P
1
10
11
2
3
M
M
1
1
2
2
N
N
2
1
EE
1
9. Attach side back panel (M) to shelving areas
using back panel screws (DD).
Repeat for remaining back panel (M).
01 . From Front the assembly, insert shelf pins (EE) at
desired height, ensuring they are level. Place
shelf (N) on top of shelf pins (EE).
Repeat for remaining the shelf (N).

10
ASSEMBLY INSTRUCTIONS (CONT’D)
13.
Hardware Used
13
Insert Bracket x 2
FF
Short Bolt x 6
GG
Locate the Insert Bracket (FF) on the right side of
the insert (R), securing with three short bolts (GG).
Repeat for the left side of the insert (R).
12. If you need to adjust the doors, do so in the following manne
To adjust door up or down, loosen screws (a) on both hinges, adjust door, and retighten screws.
r.
To adjust door left or right, turn screws (b) on both hinges, in or out.
To adjust door in or out, loosen screws (c) on both hinges, adjust door, and retighten screws.
12
2
2
cc
b
aa
1
1
3
1
1
3
2
2
2
2
FF
GG
R

11
ASSEMBLY INSTRUCTIONS (CONT’D)
.41
Hardware Used
x 4
HH
15
Screw
14
15. Secure the insert (R) to the base (K) with two
screws (HH) on the left side and on the right side
of the insert (R).
Assembly is now complete, with the help of
another person, move the assembly to the final
desired location. Once in final position you may
plug the insert (R) into the power outlet.
From behind the assembly, with the help of
another person, position the insert (R) into
opening of mantel assembly.
Note: DO NOT plug the insert (R) into power outlet
yet.
CAUTION: DO NOT slide the insert on top of wood
to avoid scratching wood surface.
R

12
Note: .)Q(lenaprooddoowdedulcniehthtiwtuodehctiwsebnacslenaproodssalgdellatsni-erpehT
1. Remove the silicone trim along the outer edges of the glass panel on the inside of the door.
Start at a corner and pull to remove the four pieces. Be careful not to damage the silicone trim as it
will be used to secure the new panel.
2. Remove the glass panel from the door frame, then insert the included wood door panel (Q).
3. Using your finger press the silicone trim back into place. Move around the outer edge of the panel
until all four sides are secure.
CHANGE DOOR PANELS (OPTIONAL)
2
123
1
2
3
4Q
1
2
4
3

13
OPERATING INSTRUCTIONS
lortnoCetomeRlenaPlortnoC
Power Function
• Press the POWER ICON to turn the main power to the unit ON or OFF.
• When the unit is powered ON, the lights under the emberbed will glow to indicate the unit
has power.
• If any functions are stored in memory then they will resume at the last setting .
Flame Brightness Function
•
• If the unit main power is OFF, you can press the FLAME BRIGHTNESS ICON to power ON
•
Note: The control panel is a touch screen. It will appear black. Touch the control panel once to
“wake up” the controls. This will cause the controls to light up. Which ever icon you touch will display
it’s last setting when you do this. At this time you can press the corresponding icon to the function you
would like to adjust. After 5 seconds the touch screen will fade to black.
Temperature Function
• Press the TEMPERATURE ICON to adjust the heater’s thermostat setting.
• If the unit is powered OFF, you can press the TEMPERATURE ICON to power ON the unit.
•
•
•
Press the TEMPERATURE ICON again to scroll up through the pre-set temperature settings:
The thermostat setting range is 65oF (18oC) to 90oF (32oC), HI (High) and OFF.
Set the temperature to "HI" to have the heater run continually.
Press and hold the TEMPERATURE & TIMER ICON for 5 seconds to toggle between 5oF
(3oC) increments and 1oF (1oC) increments when setting the temperature. The unit will beep to
indicate that the change has taken place. The factory default temperature is 5oF (3oC) increments.
The emberbed will glow at the lowest brightness setting unless a different setting was saved
in the memory.
• Hold down the TEMPERATURE ICON for 5 seconds to toggle between Fahrenheit and Celsius.
A
Note: This option is only available if using the control panel.
Note: This option is only available if using the control panel.
n “F” or “C” will display next to the temperature.
• Press and hold the TEMPERATURE ICON for 10 seconds to disengage the heater function.
Press and hold the TEMPERATURE ICON for 10 seconds again to engage the heater
function. (See HEATER OVERRIDE section below for more details).
M
Press the FLAME BRIGHTNESS ICON to adjust the flame brightness.
Press the FLAME BRIGHTNESS ICON again to scroll up through the flame brightness
settings: 1, 2, 3, 4, 5, OFF.
the unit and flame brightness will resume at the last setting.
To use the remote control,
first insert two AAA batteries
(included) into the remote
control. ensuring the polarities
of the battery match the inside
of the battery compartment.
M8:88

OPERATING INSTRUCTIONS (CONT’D)
14
Timer Function
Press the TIMER ICON to set the countdown for the unit’s main power.

Press the TIMER ICON again to scroll through the timer settings, which are: 30, 1h, 2h, 3h,
4h, 5h, 6h, 7h, 8h, 9h, OFF.（30 means 30 minutes)
When the timer reaches zero, it will turn OFF the main power and will maintain all the settings
in memory.
Downlight Function
Press the DOWNLIGHT ICON to power the LED downlights ON or OFF
If the unit is powered OFF, you can press the DOWNLIGHT ICON to power ON the unit. The
emberbed will glow at the lowest brightness setting unless a different setting was saved in
the memory.
MEMORY FUNCTION
This unit has a memory function that allows you to turn off the MAIN POWER and retains all the other
function settings (excluding the TIMER function).
When the unit’s main power is OFF, press the POWER ICON once on the insert control panel or
on the remote control to power the unit ON and “wake up” the individual function at the last setting.
Press the icon again to adjust it and press the main POWER ICON on the insert or on the remote
control to turn the unit OFF and save the new setting into memory.
When the unit is powered ON, the LED readout will show the saved temperature setting. If a temper
-ature setting was not saved, it will show the flame brightness setting saved in memory. If neither
one has a setting saved to memory, then only the emberbed will glow (as a power light indicator).
HEATER OVERRIDE
The power to the heater can be disengaged to prevent the heater from being accidentally or
unintentionally powered on. This feature is primarily added to help prevent children from powering
on the heater when it is not desired.
To engage the heater override function press and hold the HEATER ICON for 10 seconds. The
symbol E3 will display and then go blank while beeping 3 times. The heater function is now
locked. If the HEATER ICON is pressed again E3 will appear then fade.The Flame, Downlight
and Timer functions will operate normally. Only the heater and blower are disengaged.
To unlock the heater function, press and hold the HEATER ICON for 10 seconds. The symbol
E3 will display and then go blank while beeping 3 times. The heater function is now engaged.
By pressing the HEATER ICON again you will be able to adjust the heat temperature to your
desired temperature.
To reset the memory, hold down the main POWER ICON for 10 seconds at any time. When this
happens, the LED readout will blink with three zeros three times and the unit will be shut down.
Another way to reset the memory is to unplug the unit from the wall.
If the unit is powered OFF, you can press the TIMER ICON to power ON the unit. The
emberbed will glow at the lowest brightness setting unless a different setting was saved in
the memory.

CARE AND MAINTENANCE
15
Disposal of Used Battery
A battery may contain hazardous substances that could be
endangering the environment and human health.
• This symbol marked on the battery and/or packaging indicates that
used battery shall not be treated as municipal waste. Instead it shall
be left at the appropriate collection point for recycling.
• By ensuring the used battery is disposed of corr
• Do not dispose of batteries in fire. batteries may explode or leak.
ectly, you will help
prevent potential negative consequences for the environment and
human health. The recycling of materials will help to conserve
natural resources.
For more information about collection and recycling of used batteries,
please contact your local municipality, your waste disposal service or
the point-of-sale where you purchased this battery.
• Make sure the unit is turned OFF, unplugged and the heating elements of heater are cool
whenever you are cleaning the heater or fireplace.
• Clean the metal trim using a water-dampened soft, clean cloth. DO NOT use brass polish or
household cleaners as these products will damage the metal trim.
•
bearing life and require no further lubrication. However, periodic cleaning/vacuuming of the fan/
heater and air intake/output vents is recommended.
Replacing the Remote Control Batteries
When the remote control (S) stops operating or its
range seems reduced, it is time to replace the
batteries. Note: The batteries should be removed if the
product is to be left unused for a long time.
1. The battery compartment is located on the back
of the remote control (S).
2. Remove battery cover from the back of remote
control (S) and remove the old batteries.
3. Insert 2pcs AAA batteries, ensuring the polarities of
the battery match the inside of the battery
compartment.
4. Re-insert the battery door.
Note: Do not mix old and new batteries.
Do not mix alkaline, standard (carbonzinc), or rechargeable (nicad, nimh, etc) batteries.
Non-rechargeable batteries are not to be recharged. Exhausted batteries are to be removed from
the product.
Harmful if swallowed.
S
The motors used on the fan and the flame generator assembly are pre-lubricated for extended
• Any other servicing should be performed by an authorized service representative.
When the heater is not in use, the power cord should be stored properly to avoid contact with hot
or sharp objects.
•

16
PROBLEM POSSIBLE CAUSE CORRECTIVE ACTION
Error E1 displayed on
control panel.
The overheat sensor
has been engaged.
Unplug unit, wait 15-20 minutes, then the sensor will reset
itself. Plug the unit back in and turn on the heater. If the
problem persists, call customer service.
Note: The other functions will work normally excluding
the heater. Until the problem is solved, the error will only
appear/sound when the heater button is pressed.
Error E2 displayed on
control panel.
The thermostat
sensor is broken or
not working correctly.
Unplug unit, wait 15-20 minutes, then the sensor will reset
itself. Plug the unit back in and turn on the heater. If the
problem persists, call customer service.
Note: The other functions will work normally excluding
the heater. Until the problem is solved, the error will only
appear/sound when the heater button is pressed.
Error E3 displayed on
control panel.
Heater override
function is engaged
No power; logs do not
glow.
The unit does not
have power.
Check that the power cord is securely plugged into a
standard 120V outlet. Then check to make sure the unit is
powered on.
are glowing. powered off. achieved.
Heater and blower
do not power on but rest
of functions are working.
Power cord gets warm to
the touch.
Normal operation. This is normal for a heater appliance as it requires
more current to operate. Check the connections of
the appliance cord and the outlet. Make sure the plug
and outlet frequently to determine if it is HOT; if so,
discontinue use of the appliance and consult with a
outlet(s).
Remote control does not
work.
Weak or failing
batteries.
Replace with 2 AAA batteries. . (See page 15 for more
information.)
Remote control
signal is weak and only
works sometimes.
Pressing the buttons
too quickly.
Press the buttons slowly and steadily to ensure the
transmitter recognizes the request.
Using the remote
control too far away or
at an off angle.
Move closer to the insert; the remote control will only
work within a distance of 20 feet and 45 degrees to either
Fan motor continues to
blow after unit is powered
off.
Normal operation. This is a standard feature; the blower runs for an
additional time to cool off heater tubes.
TROUBLESHOOTING
Heater override
function is engaged
To unlock the heater, simply press and hold the
temperature button for 10 seconds (See page 14
Heater Override Section for more details).
To unlock the heater, simply press and hold the
temperature button for 10 seconds (See page 14
Heater Override Section for more details).

17
The manufacturer warrants that your new Electric fireplace is free from manufacturing and material
defects for a period of one year from date of purchase, subject to the following conditions and
limitations.
Install and operate this Electric fireplace in accordance with the installation and operating instructions
furnished with the product at all times. Any unauthorized repair, alteration, willful abuse, accident, or
misuse of the product shall nullify this warranty.
This warranty is non-transferable, and is made to the original owner, provided that the purchase was
made through an authorized supplier of the product.
The warranty is limited to the repair or replacement of part(s) found to be defective in material or
workmanship, provided that such part(s) have been subjected to normal conditions of use and
service, after said defect is confirmed by the manufacturer’s inspection.
The manufacturer may, at its discretion, fully discharge all obligations with respect to this warranty by
refunding the wholesale price of the defective part(s).
Any installation, labor, construction, transportation, or other related costs/expenses arising from
defective part(s), repair, replacement, or otherwise of same, will not be covered by this warranty, nor
shall the manufacturer assume responsibility for same.
The owner/user assumes all other risks, if any, including the risk of any direct, indirect or
consequential loss or damage arising out of the use, or inability to use the product, except as
provided by law.
All other warranties—expressed or implied—with respect to the product, its components and
accessories, or any obligations/liabilities on the part of the manufacturer are hereby expressly
excluded.
The manufacturer neither assumes, nor authorizes any third party to assume on its behalf, any other
liabilities with respect to the sale of the product.
The warranties as outlined within this document do not apply to non accessories used in conjunction
with the installation of this product.
This warranty is void if:
1. The fireplace is subjected to prolonged periods of dampness or condensation.
2. Any unauthorized alteration, willful abuse, accident, or misuse of the product.
3. You do not have the original receipt of purchase.
ONE-YEAR LIMITED WARRANTY

For replacement parts, call our customer service department at 1-855-571-1044, 9 a.m. - 5 p.m., EST,
Monday - Friday.
REPLACEMENT PARTS FOR 1167FMM-26-200
18
PART DESCRIPTION PART #
PU17-1167-KB
N
JJ
W
KK
JJ
U
T
RV
X
Q
O
S
P
KK C-90-107-V2
Knob
Hinge
PU17-1167FMM-23-26-200
LL Hardware Packet
U
Spinner Motor
PU16-23262833-HB
W
V
PCB Board PU16-262833-PCB
PU16-23262833-SM
T
Heater/Blower
Assembly
PU16-232628-NTC
Electric Fireplace
Remote Control
Insert
S
Thermostat
PU16-262833-RC
PF- 1167FMM-26-200-003
P Right Front
Door
Panel
Q Wood Door PF- 1167FMM-26-200-004
Panel
X
R
Glass Door PF- 1167FMM-26-005
PF-1167FMM-26-200-001
N
OPF-1167FMM-26-200-002
Wood Shelf
Left Front Door
2612-FG
LL
Item/Article/Artículo#0839834; 0849089; 0849090; 0849093;0849094;0849095
Model/Modèle/Modelo#1167FMM-23-200; 1167FMM-26-200
1167FMM-23-201;1167FMM-26-201
1167FMM-23-202;1167FMM-26-202
SCOTTLIVINGand logo are trademarks of Scott Brothers Enter tainment Inc. in the United State of America and elsewhere. Used under license.
SCOTTLIVINGet le logo sont des marques de commerce de Scott Brothers Entertainment Inc. aux États-Unis et ailleurs. Utilisé sous licence.
SCOTTLIVINGy el logo son marcas comerciales de Scott Brothers Entertainment Inc. en los Estados Unidos de América y otros paí ses. Usado bajo licencia.
TM
AA LongBolt (x30)
BoulonLong (x30)
PernoLargo (x30)
CC
WoodenDowel (x26)
GoujonDe Bois (x26)
TaqueteDe Madera (x26)
II
Touch-upPen (x1)
StyloDe Retouche (x1)
MarcadorDe Retoque (x1)
FF
InsertBracket (x2)
SupportDe L'insertion (x2)
SoporteDel Inserto (x2)
DD
BackPanel Screw (x38)
VisPanneau Arrière (x38)
TornilloDe Panel Posterior (x38)
GG
ShortBolt (x6)
BoulonCourt (x6)
PernoCorto (x6)
HH
Screw(x4)
Vis(x4)
Tornillo(x4)
BB
Washer(x30)
Rondelle(x30)
Arandela(x30)
EE
ShelfPin(x8)
ChevilleDe Tablette (x8)
PasadorDel Estante (x8)

For replacement parts, call our customer service department at 1-855-571-1044, 9 a.m. - 5 p.m., EST,
Monday - Friday.
REPLACEMENT PARTS FOR 1167FMM-26-201
19
PART DESCRIPTION PART #
PU17-1167-KB
JJ
KK
C-90-107-V2
Knob
Hinge
PU17-1167FMM-23-26-201
LL Hardware Packet
U
Spinner Motor
PU16-23262833-HB
W
V
PCB Board PU16-262833-PCB
PU16-23262833-SM
T
Heater/Blower
Assembly
PU16-232628-NTC
Electric Fireplace
Remote Control
Insert
S
Thermostat
PU16-262833-RC
PF- 1167FMM-26-201-003
P Right Front
Door
Panel
Q Wood Door PF- 1167FMM-26-201-004
Panel
X
R
Glass Door PF- 1167FMM-26-005
PF-1167FMM-26-201-001
N
OPF-1167FMM-26-201-002
Wood Shelf
Left Front Door
2612-FG
N
JJ
W
KK
U
T
RV
X
Q
O
S
P
LL
Item/Article/Artículo#0839834; 0849089; 0849090; 0849093;0849094;0849095
Model/Modèle/Modelo#1167FMM-23-200; 1167FMM-26-200
1167FMM-23-201;1167FMM-26-201
1167FMM-23-202;1167FMM-26-202
SCOTTLIVINGand logo are trademarks of Scott Brothers Enter tainment Inc. in the United State of America and elsewhere. Used under license.
SCOTTLIVINGet le logo sont des marques de commerce de Scott Brothers Entertainment Inc. aux États-Unis et ailleurs. Utilisé sous licence.
SCOTTLIVINGy el logo son marcas comerciales de Scott Brothers Entertainment Inc. en los Estados Unidos de América y otros paí ses.Usado bajo licencia.
TM
AA LongBolt (x30)
BoulonLong (x30)
PernoLargo (x30)
CC
WoodenDowel (x26)
GoujonDe Bois (x26)
TaqueteDe Madera (x26)
II
Touch-upPen (x1)
StyloDe Retouche (x1)
MarcadorDe Retoque (x1)
FF
InsertBracket (x2)
SupportDe L'insertion (x2)
SoporteDel Inserto (x2)
DD
BackPanel Screw (x38)
VisPanneau Arrière (x38)
TornilloDe Panel Posterior (x38)
GG
ShortBolt (x6)
BoulonCourt (x6)
PernoCorto (x6)
HH
Screw(x4)
Vis(x4)
Tornillo(x4)
BB
Washer(x30)
Rondelle(x30)
Arandela(x30)
EE
ShelfPin(x8)
ChevilleDe Tablette (x8)
PasadorDel Estante (x8)

For replacement parts, call our customer service department at 1-855-571-1044, 9 a.m. - 5 p.m., EST,
Monday - Friday.
REPLACEMENT PARTS FOR 1167FMM-26-202
20
PART DESCRIPTION PART #
PU17-1167-KB
JJ
KK
C-90-107-V2
Knob
Hinge
PU17-1167FMM-23-26-202
LL Hardware Packet
U
Spinner Motor
PU16-23262833-HB
W
V
PCB Board PU16-262833-PCB
PU16-23262833-SM
T
Heater/Blower
Assembly
PU16-232628-NTC
Electric Fireplace
Remote Control
Insert
S
Thermostat
PU16-262833-RC
PF- 1167FMM-26-202-003
P Right Front
Door
Panel
Q Wood Door PF- 1167FMM-26-202-004
Panel
X
R
Glass Door PF- 1167FMM-26-005
PF-1167FMM-26-202-001
N
OPF-1167FMM-26-202-002
Wood Shelf
Left Front Door
2612-FG
N
JJ
W
KK
U
T
RV
X
Q
O
S
P
LL
Item/Article/Artículo#0839834; 0849089; 0849090; 0849093;0849094;0849095
Model/Modèle/Modelo#1167FMM-23-200; 1167FMM-26-200
1167FMM-23-201;1167FMM-26-201
1167FMM-23-202;1167FMM-26-202
SCOTTLIVINGand logo are trademarks of Scott Brothers Enter tainment Inc. in the United State of America and elsewhere. Used under license.
SCOTTLIVINGet le logo sont des marques de commerce de Scott Brothers Entertainment Inc. aux États-Unis et ailleurs. Utilisé sous licence.
SCOTTLIVINGy el logo son marcas comerciales de Scott Brothers Entertainment Inc. en los Estados Unidos de América y otros paí ses.Usado bajo licencia.
TM
AA LongBolt (x30)
BoulonLong (x30)
PernoLargo (x30)
CC
WoodenDowel (x26)
GoujonDe Bois (x26)
TaqueteDe Madera (x26)
II
Touch-upPen (x1)
StyloDe Retouche (x1)
MarcadorDe Retoque (x1)
FF
InsertBracket (x2)
SupportDe L'insertion (x2)
SoporteDel Inserto (x2)
DD
BackPanel Screw (x38)
VisPanneau Arrière (x38)
TornilloDe Panel Posterior (x38)
GG
ShortBolt (x6)
BoulonCourt (x6)
PernoCorto (x6)
HH
Screw(x4)
Vis(x4)
Tornillo(x4)
BB
Washer(x30)
Rondelle(x30)
Arandela(x30)
EE
ShelfPin(x8)
ChevilleDe Tablette (x8)
PasadorDel Estante (x8)