Greentouch 1341FM-30-351 Quickspecs

1
MENARDS ITEM #641-5291
MODEL #1341FM-30-351
ATTACH YOUR RECEIPT HERE
54” ELECTRIC FIREPLACE
ENTERTAINMENT CENTER
ASSEMBLY, CARE & USE INSTRUCTIONS
Serial Number__________________ Purchase Date__________________
Questions, problems, missing parts? Before returning to your retailer, call our customer service department
at 1-855-571-1044 9 a.m. - 5 p.m., EST, Monday - Friday. www.greentouchhome.com.

2
TABLE OF CONTENTS
Package Contents...........................................................................................................................................................3
Hardware Contents .........................................................................................................................................................4
Safety Information ..........................................................................................................................................................4
Preparation.....................................................................................................................................................................8
Assembly Instructions.....................................................................................................................................................8
Maximum Recommended Weight Loads........................................................................................................................20
Operating Instructions...................................................................................................................................................21
Care And Maintenance..................................................................................................................................................23
Troubleshooting ............................................................................................................................................................24
One-Year Limited Warranty ...........................................................................................................................................25
Replacement Parts List .................................................................................................................................................26

3
PACKAGE CONTENTS
A
B
C
C
D
E
F
G
H
I
J
K
M
N
O
Q
R
R
S
T
L
I
B
PART DESCRIPTION QUANTITY
ATop 1
B Corner Panel 2
C Partition Panel 2
D Center Shelf (with heater) 1
ELeft Middle Wall 1
FRight Middle Wall 1
GLeft Outer Wall 1
HRight Outer Wall 1
I Shelf 2
J Left Door 1
K Right Door 1
PART DESCRIPTION QUANTITY
LFireplace Brick Wall 1
M Fire Log 1
N Fireplace Grate 1
ORemote Control (Battery
Inside) 1
Q Center Back Panel 1
R Back Panel 2
S Fireplace Glass Front 1
T Base 1

4
HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)
AA BB CC DD EE FF GG
HH II JJ KK LL MM NN
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. The equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on. The user is encouraged to try and correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Long Screw
x 8
Wooden Dowel
x 36
Connecting
Rod
x 24
Locknut
x 24
Back panel
mounting
hardware (with
screw)
x 20
L-Bracket
x 2
Short Screw
x 4
Shelf Pin
x 8
Door Pull
x 2
Hinge
x 4
Hinge Screw
x 24
Touch-up Pen
x 1
Screw
x 2
Tip Restraint
Hardware
x 2

5
SAFETY INFORMATION (CONTINUED)
Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock
and injury to persons, including the following:
DANGER
• Read all instructions before installing or using this heater.
• If the information in this manual is not followed exactly, an electric shock or fire may result causing property damage,
personal injury or loss of life.
• ALWAYS unplug this appliance/furnishing from the electrical outlet before cleaning or servicing.
• This product is intended to fit most plasma and LCD televisions (up to 60 inches and weighing a maximum of 80
pounds). Using this item with loads heavier than the stated maximum can result in tipping and/or instability, which
can result in injury or even death.
WARNING
• This appliance is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. Keep combustible
material, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet from this appliance and keep
them away from the sides and rear.
• Extreme caution is necessary when any heater is used by or near children or individuals with disabilities and
whenever the fireplace is left operating and unattended.
• DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings.
• DO NOT route cord under furniture or appliances. Arrange cord away from traffic areas and where it will not be
tripped over.
• DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric
shock or fire, or damage the appliance.
• This appliance has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint or
flammable vapors or liquids are used or stored. This fireplace should not be used as a drying rack for clothing.
Christmas stockings or decorations should not be hung in the area of it.
• Use this appliance only as described in the manual. Any other use is NOT recommended by the manufacturer and
may cause fire, electric shock or injury to persons.
• Unplug from outlet before putting on or taking off parts.
• Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
• Use this furnishing only for its intended use as described in these instructions. DO NOT use attachments not
recommended by the manufacturer.
• Keep the cord away from heated surfaces.
• Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and other debris.
• Never drop or insert any object into any opening.
• DO NOT operate where aerosol (spray) products are being used or where oxygen is being administered.
• To disconnect, turn all controls to the off position, then remove plug from outlet.

6
SAFETY INFORMATION (CONTINUED)
• Each surface intended to support a load shall have a corresponding statement in the use instructions specifying the
maximum intended load for that surface in pounds (kilograms).
• Risk of electric shock-connect this furnishing to a properly grounded outlet only. See Grounding Instructions.
• To avoid electric shock, fire, or injury, review the assembly instructions to confirm that the appropriate critical
components and accessories are being used with the furnishing.
• Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or
toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip
over on to the child.
• Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video
equipment may result in death or serious injury due to the furnishing collapsing or overturning onto a child.
CAUTION
• DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions. DO NOT operate
any heater if it has been dropped or damaged in any manner. Disconnect power at service panel and have heater
inspected by a reputable electrician before reusing.
• Any repairs to this fireplace should be carried out by a qualified service person.
• Under no circumstances should this fireplace be modified. Parts having to be removed for servicing must be replaced
prior to operating this fireplace again.
• Household use only.
• DO NOT use outdoors.
• “WARNING – Death or serious injury may occur when children climb on audio and/or video equipment furniture. A
remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the
furnishing may tip over on to the child”.
• “WARNING – Relocating audio and/or video equipment to furniture not specifically designed to support audio and/
or video equipment may result in death or serious injury due to the furnishing collapsing or overturning onto a child”.
• This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER place heater
where it may fall into a bathtub or other water container.
• To disconnect this appliance, turn controls to the OFF position, then remove plug from outlet.
• ONLY connect to properly grounded outlets.
• This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA
C22.1 Canadian Electrical Code or follow U.S.A. Installations, follow local codes and the National Electrical Code, ANSI/
NFPA N0.70.
• To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like
a bed, where opening may become blocked.
• The heaters MUST NOT be located immediately below a socket-outlet.
• ALWAYS plug heaters directly into a wall outlet / receptacle. NEVER use with an extension cord or re-loadable
power tap (outlet / power strip).
• DO NOT slide insert on top of wood to avoid scratching wood surface.
• DO NOT place any object on top of the insert or block the air intakes / vents as this can cause the unit to overheat
and could cause a fire.

7
SAFETY INFORMATION (CONTINUED)
Electrical Connection
• A 15-Amp, 120-volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a
dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow
when the heater is in operation. The unit comes standard with 6-ft. three-wire cord, exiting from the rear of the
fireplace. DO NOT exceed the current rating of the current tap.
Grounding Instructions
• This heater is for use on 120 volt. The cord has a plug as shown below. See illustration or grounding instruction. An
adapter as shown at C is available for connecting three-blade grounding type plugs to two-slot receptacles. The green
grounding plug extending from the adapter must be connected to a permanent ground such as a properly grounded
outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
A B C
Grounding Pin
Grounding Means
Metal
Screw
Cover of
Grounding
Box
Adapter
SAVE THESE INSTRUCTIONS

8
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 50 minutes
Tools Required for Assembly (not included): Phillips screwdriver
ASSEMBLY INSTRUCTIONS
1. Align the hinges (JJ) with the predrilled holes on the right outer wall (H), securing each hinge with four hinge screws
(KK).
Repeat for the remaining hinges (JJ).
2
G
H
KK
JJ
JJ
x 4
Hinge
KK
x 16
Hinge Screw

9
ASSEMBLY INSTRUCTIONS (CONTINUED)
2. Insert ten wooden dowels (BB) into the designated holes on the base (T). Align and attach the left outer wall (G) onto
the dowels. Fasten the wall from underneath with two long screws (AA) using a Phillips Head Screwdriver.
Repeat for right outer wall (H), left middle wall (E) and right middle wall (F).
2
1
1
1
1
T
G
E
FH
BB
AA
AA
x 8
Long Screw
BB
x 10
Wooden Dowel
3. Attach the fireplace glass front (S), lowering it into the front groove on the base (T). Secure the glass by turning the
pre-assembled plastic knobs.
2
S
T
1

10
ASSEMBLY INSTRUCTIONS (CONTINUED)
4. As shown in the diagram, insert the back panels (R) along the grooves of the middle walls (E, F) and outer walls (G, H).
R
GE
FH
R
5. Place the center shelf (D) upside down onto a scratch free surface such as a foam sheet that came in the packaging.
Screw eight connecting rods (CC) into the designated holes on the back of the center shelf (D).
D
CC
CC
x 8
Connecting Rod

11
ASSEMBLY INSTRUCTIONS (CONTINUED)
6. Insert ten wooden dowels (BB) & eight locknuts (DD) into the corresponding holes on both left middle wall (E), right
middle wall (F), left outer wall (G) and right outer wall (H).
Turn the locking nut in clockwise direction up to 180° from the connection joint to properly secure the center shelf (D).
1
D
GE
FH
BB
DD
2
BB
x 10
Wooden Dowel
DD
x 8
Locknut
7. Screw eight connecting rods (CC) into the designated holes on the top of the center shelf (D).
D
CC
CC
x 8
Connecting Rod

12
ASSEMBLY INSTRUCTIONS (CONTINUED)
8. Insert eight wooden dowels (BB) into the top holes of center shelf (D), and insert eight locknuts (DD) into the
corresponding holes of the corner panels (B) and partition panels (C).
Turn the locking nut in clockwise direction up to 180° from the connection joint to properly secure the corner panels
(B) and partition panels (C).
2
11
1
1
D
BC
C
B
DD
BB
BB
x 8
Wooden Dowel
DD
x 8
Locknut
9. As shown in the diagram, insert the center back panel (Q) into the grooves of the corner panels (B).
B
B
Q

13
ASSEMBLY INSTRUCTIONS (CONTINUED)
10. Place the top (A) upside down onto a scratch free surface such as a foam sheet that came in the packaging. Screw
eight connecting rods (CC) into the designated holes on the back of the top (A).
CC
A
CC
x 8
Connecting Rod
11. Insert eight wooden dowels (B) & eight locknuts (DD) into the corresponding holes of corner panels (B) and partition
panels (C).
Turn the locking nut in clockwise direction up to 180° from the connection joint to properly secure the top (A).
2
A
1
BB
DD
B
B
C
C
BB
x 8
Wooden Dowel
DD
x 8
Locknut

14
ASSEMBLY INSTRUCTIONS (CONTINUED)
12. Secure the back panels (R) and center back panel (Q) to the product using the back panel mounting hardware (EE).
Fasten the screws with a Phillips screwdriver (As shown in diagram 12).
1
2
Q
R
R
EE
EE
x 20
Back panel mounting
hardware
13. Place the fireplace grate (N) by matching the bottom pins into the holes on the base (T).
N
T

15
ASSEMBLY INSTRUCTIONS (CONTINUED)
14. Remove the film from the adhesive on the top of the fireplace grate (N) and place the fire log (M) on the center of the
fireplace grate (N).
1
2
M
N
15. Screw two L-bracket (FF) onto the fireplace brick wall (L) using four short screws (GG).
L
GG
FF
FF
x 2
L-Bracket
GG
x 4
Short Screw

16
ASSEMBLY INSTRUCTIONS (CONTINUED)
16. Align the USB cable from behind through the cable hole on the fireplace brick wall (L). Attach the USB cable from the
heater into the USB port behind the fireplace grate (N). Insert the fireplace brick wall (L) into the mantel, slotting it
into the grooves on base (T). Secure it by using two screws (MM) into the L-bracket (FF).
1
3
MM
FF
2
LMM
T
MM
x 2
Screw
17. Insert shelf pins (HH) at desired height, ensuring they are level. Place shelves (I) on top of the shelf pins (HH).
1
HH
2
2
I
I
HH
x 8
Shelf Pin

17
ASSEMBLY INSTRUCTIONS (CONTINUED)
18. Place the door pull (II) into predrilled hole on right door (K), securing with two door pull screws.
Repeat for remaining door pull (II).
J
K
II
II
x 2
Door Pull
19. Align the hinges with the predrilled holes on the left door (J), securing each hinge with two hinge screws (KK).
Repeat the same steps for the right door (K).
2
KK1
J
G
H
K
KK
x 8
Hinge Screw

18
ASSEMBLY INSTRUCTIONS (CONTINUED)
20. NOTE: Use the pre-assembled levelers on the base of the fireplace to level the unit. Twist the levelers
counter-clockwise to increase the height, twist clockwise to decrease the height.
1/2 in.
21. If you need to adjust the doors, do so in the following manner.
To adjust door up or down, loosen screws (a) on both hinges, adjust door, and retighten screws.
To adjust door left or right, turn screws (b) on both hinges, in and out.
To adjust door in or out, loosen screws (c) on both hinges, adjust door, and retighten screws.
2
2
22
2
2
1
1
b
a
1
a
3
c
1
c
3

19
ASSEMBLY INSTRUCTIONS (CONTINUED)
WARNING: You must install the tip restraint hardware to help prevent any accidents or damage to the unit. We strongly
recommend attaching the tip restraint hardware to a wall stud and your unit. For all other wall types, please visit your local
hardware store to obtain the proper hardware.
Assembly is now complete. With the help of another person, move the unit to the final desired position. Once in the final
position, you may attach the tip restraint hardware to the wall. You may now plug the heater into the power outlet.
1
NN
Wall Stud
2
NN
x 2
Tip Restraint
Hardware

20
MAXIMUM RECOMMENDED WEIGHT LOADS
WARNING
For use with televisions weighing 80 lbs or less.
Use with heavier televisions may result instability causing tip over resulting in death or serious injury.
SKU#641-5291/Model#1341FM-30-351
DISTRIBUTION: Greentouch USA Inc
ADDRESS: 207 Byers Creek Rd Ste D Mooresville, NC 28117-6988
COUNTRY OF ORIGIN: VIETNAM
MANUFACTURE DATE: JUN, 2022
(This date is accordance with the actual manufacture date.)
FITS UP TO MOST 152.4 cm / 60 in FLAT PANEL TVS
MAXIMUM LOAD 36.28 kg / 80 lb
MAXIMUM LOAD 15.87 kg / 35 lb
MAXIMUM LOAD 6.8 kg / 15 lb
MAXIMUM LOAD 6.8 kg / 15 lb
MAXIMUM LOAD 6.8 kg / 15 lb
MAXIMUM LOAD 6.8 kg / 15 lb
MAXIMUM LOAD 6.8 kg / 15 lb
MAXIMUM LOAD 6.8 kg / 15 lb