Greentouch 1358FM-26-344 Quickspecs

1
MENARDS ITEM #641-5292
MODEL #1358FM-26-344
ATTACH YOUR RECEIPT HERE
60” ELECTRIC FIREPLACE
ENTERTAINMENT CENTER
ASSEMBLY, CARE & USE INSTRUCTIONS
Serial Number__________________ Purchase Date__________________
Questions, problems, missing parts? Before returning to your retailer, call our customer service department
at 1-855-571-1044 9 a.m. - 5 p.m., EST, Monday - Friday. www.greentouchhome.com.

2
TABLE OF CONTENTS
Package Contents...........................................................................................................................................................3
Hardware Contents .........................................................................................................................................................4
Safety Information ..........................................................................................................................................................4
Preparation.....................................................................................................................................................................8
Assembly Instructions.....................................................................................................................................................8
Maximum Recommended Weight Loads........................................................................................................................19
Operating Instructions...................................................................................................................................................20
Care And Maintenance..................................................................................................................................................22
Troubleshooting ............................................................................................................................................................23
One-Year Limited Warranty ...........................................................................................................................................24
Replacement Parts List .................................................................................................................................................25

3
PACKAGE CONTENTS
AB
C
D
F
G
H
I
J
L
Q
S
R
M
N
O
K
I
H
E
PART DESCRIPTION QUANTITY
ATop 1
B Front Bar 1
CLeft Middle Wall 1
DRight Middle Wall 1
ELeft Outer Wall 1
FRight Outer Wall 1
G Center Shelf 1
HShelf 2
I Back Panel 2
J Center Back Panel 1
PART DESCRIPTION QUANTITY
K Left Door 1
L Right Door 1
M Fire log 1
N Fireplace Grate 1
ORemote Control
(Battery Inside) 1
Q Fireplace Glass front 1
R Base 1
S Fireplace Brick wall 1

4
HARDWARE CONTENTS (NOT SHOWN ACTUAL SIZE)
AA BB CC DD EE FF GG
HH II JJ LL PP
SAFETY INFORMATION
Please read and understand this entire manual before attempting to assemble, operate or install the product.
This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of
the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential
installation. The equipment generates, uses and can radiate radio frequency energy and, if not installed and used
in accordance with the instructions, may cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on. The user is encouraged to try and correct the interference by one or
more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions:
1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.
Long Screw
x 4
Wooden Dowel
x 24
Locknut
x 20
Connecting Rod
x 20
Back panel
mounting
hardware
(with screw)
x 12
Screw
x 6
L-Bracket
x 2
Shelf Pin
x 8
Door Pull
x 2
Door Stopper
x 2
Touch-up Pen
x 1
Tip Restraint
Hardware
x 2

5
SAFETY INFORMATION (CONTINUED)
Modifications not approved by the party responsible for compliance could void user’s authority to operate the equipment.
This Class B digital apparatus complies with Canadian ICES-003.
IMPORTANT INSTRUCTIONS
When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock
and injury to persons, including the following:
DANGER
• Read all instructions before installing or using this heater.
• If the information in this manual is not followed exactly, an electric shock or fire may result causing property damage,
personal injury or loss of life.
• ALWAYS unplug this appliance/furnishing from the electrical outlet before cleaning or servicing.
• This product is intended to fit most plasma and LCD televisions (up to 65 inches and weighing a maximum of 85
pounds). Using this item with loads heavier than the stated maximum can result in tipping and/or instability, which
can result in injury or even death.
WARNING
• This appliance is hot when in use. To avoid burns, DO NOT let bare skin touch hot surfaces. Keep combustible
material, such as furniture, pillows, bedding, papers, clothes and curtains at least 3 feet from this appliance and keep
them away from the sides and rear.
• Extreme caution is necessary when any heater is used by or near children or individuals with disabilities and
whenever the fireplace is left operating and unattended.
• DO NOT run cord under carpeting. DO NOT cover cord with throw rugs, runners, or similar coverings.
• DO NOT route cord under furniture or appliances. Arrange cord away from traffic areas and where it will not be
tripped over.
• DO NOT insert or allow foreign objects to enter any ventilation or exhaust opening as this may cause an electric
shock or fire, or damage the appliance.
• This appliance has hot and arcing or sparking parts inside. DO NOT use it in areas where gasoline, paint or
flammable vapors or liquids are used or stored. This fireplace should not be used as a drying rack for clothing.
Christmas stockings or decorations should not be hung in the area of it.
• Use this appliance only as described in the manual. Any other use is NOT recommended by the manufacturer and
may cause fire, electric shock or injury to persons.
• Unplug from outlet before putting on or taking off parts.
• Close supervision is necessary when this furnishing is used by, or near children, invalids, or disabled persons.
• Use this furnishing only for its intended use as described in these instructions. DO NOT use attachments not
recommended by the manufacturer.
• Keep the cord away from heated surfaces.
• Never operate the furnishing with the air openings blocked. Keep the air openings free of lint, hair, and other debris.
• Never drop or insert any object into any opening.
• DO NOT operate where aerosol (spray) products are being used or where oxygen is being administered.
• To disconnect, turn all controls to the off position, then remove plug from outlet.

6
SAFETY INFORMATION (CONTINUED)
• Each surface intended to support a load shall have a corresponding statement in the use instructions specifying the
maximum intended load for that surface in pounds (kilograms).
• Risk of electric shock-connect this furnishing to a properly grounded outlet only. See Grounding Instructions.
• To avoid electric shock, fire, or injury, review the assembly instruction to confirm that the appropriate critical
components and accessories are being used with the furnishing.
• Death or serious injury may occur when children climb on audio and/or video equipment furniture. A remote control or
toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the furnishing may tip
over on to the child.
• Relocating audio and/or video equipment to furniture not specifically designed to support audio and/or video
equipment may result in death or serious injury due to the furnishing collapsing or overturning onto a child.
CAUTION
• DO NOT operate any heater with a damaged cord or plug or after the heater malfunctions. DO NOT operate
any heater if it has been dropped or damaged in any manner. Disconnect power at service panel and have heater
inspected by a reputable electrician before reusing.
• Any repairs to this fireplace should be carried out by a qualified service person.
• Under no circumstances should this fireplace be modified. Parts having to be removed for servicing must be replaced
prior to operating this fireplace again.
• Household use only.
• DO NOT use outdoors.
• “WARNING – Death or serious injury may occur when children climb on audio and/or video equipment furniture. A
remote control or toys placed on the furnishing may encourage a child to climb on the furnishing and as a result the
furnishing may tip over on to the child”.
• “WARNING – Relocating audio and/or video equipment to furniture not specifically designed to support audio and/
or video equipment may result in death or serious injury due to the furnishing collapsing or overturning onto a child”.
• This heater is not intended for use in bathrooms, laundry areas and similar indoor locations. NEVER place heater
where it may fall into a bathtub or other water container.
• To disconnect this appliance, turn controls to the OFF position, then remove plug from outlet.
• ONLY connect to properly grounded outlets.
• This appliance, when installed, must be electrically grounded in accordance with local codes, with the current CSA
C22.1 Canadian Electrical Code or follow U.S.A. Installations, follow local codes and the National Electrical Code, ANSI/
NFPA N0.70.
• To prevent a possible fire, DO NOT block air intakes or exhaust in any manner. DO NOT use on soft surfaces, like
a bed, where opening may become blocked.
• The heaters MUST NOT be located immediately below a socket-outlet.
• ALWAYS plug heaters directly into a wall outlet / receptacle. NEVER use with an extension cord or re-loadable
power tap (outlet / power strip).
• DO NOT slide insert on top of wood to avoid scratching wood surface.
• DO NOT place any object on top of the insert or block the air intakes / vents as this can cause the unit to overheat
and could cause a fire.

7
SAFETY INFORMATION (CONTINUED)
Electrical Connection
• A 15-Amp, 120-volt, 60 Hz circuit with a properly grounded outlet is required. Preferably, the fireplace will be on a
dedicated circuit as other appliances on the same circuit may cause the circuit breaker to trip or the fuse to blow
when the heater is in operation. The unit comes standard with 6-ft. three-wire cord, exiting from the rear of the
fireplace. DO NOT exceed the current rating of the current tap.
Grounding Instructions
• This heater is for use on 120 volt. The cord has a plug as shown below. See illustration or grounding instruction. An
adapter as shown at C is available for connecting three-blade grounding type plugs to two-slot receptacles. The green
grounding plug extending from the adapter must be connected to a permanent ground such as a properly grounded
outlet box. The adapter should not be used if a three-slot grounded receptacle is available.
A B C
Grounding Pin
Grounding Means
Metal
Screw
Cover of
Grounding
Box
Adapter
SAVE THESE INSTRUCTIONS

8
PREPARATION
Before beginning assembly of product, make sure all parts are present. Compare parts with package contents list and
hardware contents list. If any part is missing or damaged, do not attempt to assemble the product.
Estimated Assembly Time: 50 minutes
Tools Required for Assembly (not included): Phillips screwdriver
ASSEMBLY INSTRUCTIONS
1. Place the left middle wall (C) onto a scratch free surface such as a sheet that came in the
packaging. Screw two connecting rods (DD) into the holes on the back of the left middle wall (C). Fully tighten with a
Phillips screwdriver.
Repeat for right middle wall (D).
DD
CD
DD
x 4
Connecting Rod

9
ASSEMBLY INSTRUCTIONS (CONTINUED)
2. Insert two wooden dowels (BB) into each side of the center shelf (G). Align the dowels in center shelf (G) to the left
middle door (C), secure by fastening two locknuts (CC) with a Phillips screwdriver.
Repeat for right middle wall (D).
BB
CC
C
G
D
2
BB
x 4
Wooden Dowel
CC
x 4
Locknut
3. Insert four wooden dowels (BB) into the holes of base (R), align and attach the assembly from step 2 to the base (R),
securing from underneath with four long screws (AA).
1
1
2
R
BB
AA
AA
x 4
Long Screw
BB
x 4
Wooden Dowel

10
ASSEMBLY INSTRUCTIONS (CONTINUED)
4. Screw four connecting rods (DD) into the designated holes on the top of the base (R).
R
DD
DD
x 4
Connecting Rod
5. Insert four wooden dowels (BB) into the outer holes on the base (R). Attach the left outer wall (E) and secure by
fastening two locknuts (CC) with a Phillips screwdriver.
Repeat for remaining right outer walls (F).
E
F
1
1
2
R
CC
BB
x 4
Wooden Dowel
CC
x 4
Locknut

11
ASSEMBLY INSTRUCTIONS (CONTINUED)
6. As shown in the diagram, insert the center back panel (J) and back panels (I) along the grooves of the middle walls
(C,D) and outer walls (E,F).
J
I
I
7. Screw twelve connecting rods (DD) into the designated holes on the back of the top (A).
A
DD
DD
x 12
Connecting Rod

12
ASSEMBLY INSTRUCTIONS (CONTINUED)
8. Place top (A) onto a scratch free surface such as a sheet that came in the packaging. Insert two wooden dowels (BB)
into the top outer holes on the top (A). Align and attach the front bar (B) to the top (A), secure by screwing four
locknuts (CC) by Phillips screwdriver.
B
A
1
2
BB
CC
BB
x 2
Wooden Dowel
CC
x 4
Locknut
9. Insert ten wooden dowels (BB) into the top holes on both left middle wall (C), right middle wall (D), outer walls (E,F).
Attach top (A), secure by screwing eight locknuts (CC) by Phillips screwdriver.
A
1
1
2
BB
CC
BB
x10
Wooden Dowel
CC
x 8
Locknut

13
ASSEMBLY INSTRUCTIONS (CONTINUED)
10. Secure the back panels (I) and center back panel (J) to the product by using the back panel mounting hardware (EE),
screwing the screws by Phillips screwdriver (As shown in diagram ).
J
I
I
1
EE
x 12
Back panel mounting
hardware
11. Insert shelf pins (HH) at desired height, ensuring they are level. Place shelf (H) on top of shelf pins (HH).
Repeat for remaining shelf (H).
1
HH
2
H
H
2
HH
x 8
Shelf Pin

14
ASSEMBLY INSTRUCTIONS (CONTINUED)
12. Align the door pull (II) with the pre-drilled hole on the left door(K), securing with two door pull screws.
Repeat for remaining door pull (II).
K
L
II
II
x 2
Door Pull
13. Align the left door (K) with the roller track.
With the door hanger latched onto the roller track, push the left door (K) to the right.
Install the door stopper (JJ) to left end of the roller track as indicated.
Repeat to attach the right door (L).
2
1JJ
K
L
JJ
x 2
Door Stopper

15
ASSEMBLY INSTRUCTIONS (CONTINUED)
14. As shown in the diagram, Unscrew the screw holding the slider (KK) on the back of the left door (K) by using a Philips
screwdriver, Position the slider (KK) into the groove on the base (R) in place. and tighten the screw.
Repeat for remaining slider (KK) on the back of the right door (L).
R
KK
1
2
K
L
3
15. Attach the fireplace glass front (Q) into the front groove on the base (R). Secure the glass by turning the
pre-assembled plastic knobs.
Q
2
1

16
ASSEMBLY INSTRUCTIONS (CONTINUED)
16. Position the firepalce grate (N) by matching the pin on the bottom of the fireplace grate (N) to the holes on the base
(R).
N
17. Remove the film from the adhesive on the top of the fireplace grate (N) and place the fire log (M) on the center of the
fireplace grate (N).
Align the USB cable from behind through the cable hole on the freplace brick wall (I). Connect the USB cable from
the heater into the USB port behind the freplace grate (N).
1
M
N
2
3

17
ASSEMBLY INSTRUCTIONS (CONTINUED)
Note: The fireplace brick wall (S) is reversible. Choose the brick pattern for your firebox before installing the next step.
18. Screw two L-bracket (GG) onto the fireplace brick wall (S) by using four screws (FF).
FF
GG
1
2
S
S
FF
x 4
Screw
GG
x 2
L-Bracket
19. Insert the fireplace brick wall (I) into the grooves on base (R). Secure it by using two screws (FF) into the L-bracket
(EE).
FF
1
2
S
FF
x 2
Screw

18
ASSEMBLY INSTRUCTIONS (CONTINUED)
NOTE: Use the pre-assembled levelers on the base of the fireplace to level the unit. Twist the levelers counter-clockwise
to increase the height, twist clockwise to decrease the height.
1/2 in.
WARNING: You must install the tip restraint hardware to help prevent any accidents or damage to the unit. We strongly
recommend attaching the tip restraint hardware to a wall stud and your unit. For all other wall types, please visit your
local hardware store to obtain the proper hardware.
Assembly is now complete. With the help of another person, move the unit to the final desired position. Once in the final
position, you may attach the tip restraint hardware to the wall. You may now plug the heater into the power outlet.
PP
21
Wall Stud
PP
x 2
Tip Restraint
Hardware

19
MAXIMUM RECOMMENDED WEIGHT LOADS
WARNING
For use with televisions weighing 85 lbs or less.
Use with heavier televisions may result instability causing tip over resulting in death or serious injury.
SKU#641-5292/Model#1358FM-26-344
DISTRIBUTION: Greentouch USA Inc
ADDRESS: 207 Byers Creek Rd Ste D Mooresville, NC 28117-6988
COUNTRY OF ORIGIN: CHINA
MANUFACTURE DATE: MAY, 2022
(This date is accordance with the actual manufacture date.)
FITS UP TO MOST 165.1 cm / 65 in FLAT PANEL TVS
MAXIMUM LOAD 38.55 kg / 85 lb
MAXIMUM LOAD 9.07 kg / 20 lb
MAXIMUM LOAD 6.8 kg / 15 lb
MAXIMUM LOAD 6.8 kg / 15 lb
MAXIMUM LOAD 6.8 kg / 15 lb
MAXIMUM LOAD 6.8 kg / 15 lb

20
OPERATING INSTRUCTIONS
Control Panel Remote Control
To use the remote control, first remove the
plastic tab by gently pulling it out of remote
control.
Controls and Display
The control panel will display the heater setting when the unit power is turned ON. Whichever control icon you press will
display the current setting of the corresponding function. Press the control icon again to adjust the setting. Following
adjustment of any setting(s), the unit will resume to display the heater setting after 5 seconds.
Power Function
• When the unit is plugged-in but not in use, F or C will illuminate to indicate that it is in stand-by mode.
• Press the POWER ICON to turn the main power to the unit ON or OFF.
• When the unit is powered ON, the control panel will display the heater setting to indicate the unit has power.
• Functions stored in memory will resume at the last setting.
• When the unit is powered OFF, the fan will continue to blow for a 40 second cool-down cycle prior to shutting
down (a countdown will be displayed).
Flame Brightness Function
• Press the FLAME BRIGHTNESS ICON to display the current flame brightness setting.
• Press the FLAME BRIGHTNESS ICON again to scroll down through the flame brightness settings:
5, 4, 3, 2, 1, OF (OFF).
Flame Speed Function
• Press the FLAME SPEED ICON to display the current flame speed setting.
• Press the FLAME SPEED ICON again to scroll down through the flame speed settings: 5, 4, 3, 2, 1.