Grifco E960G User manual

To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with CR2032 coin batteries.
• DO NOT recharge, disassemble or heat above
100°C or incinerate.
4 Buttons
• Configure each button to operate any current
operator in the Grifco, Merlin or Chamberlain DIY
portfolio
• Buttons have raised dots to indicate door number
• Buttons can be configured to open multiple doors
or open / close an individual door
Keyring
• Keyring included
LED Indicator
• Green LED indicates when
transmitter is in operation
(useful battery check)
• Used when programming
(learning) transmitters to
operators
Surrounding Metal Edge
• Extra durability & styling
• Protects the edge of the
transmitter against potential
damage due to dropping
Device Naming Panel
• White space to
name the transmitter
• Mark the apartment
number, transmitter
reference code or
name etc
Security +2.0 / Security+
• Transmitter can be used with operators
using Security +2.0 or Security+ codes
• Any button can be programmed to
operate any operator with either code
UNIT 1
(example only)
4-CHANNEL TRANSMITTER
Wireless Keyring Transmitter compatible with Security+ and Security +2.0
MODEL: E960G
2. Programming via the Grifco C10A (Security +2.0) Wall Control
eDrive +2.0 operators are supplied with a RADIO LOCK bridge on the main circuit board.
This lock will have to be removed before programming any wireless transmitters. The
RADIO LOCK can be replaced after programming is complete. See the eDrive +2.0 manual
for more information. To program the wireless transmitter perform the following steps:
1. Press and hold the SET button on the GRIFCO front panel, then;
2. While holding the SET button, press the STOP button 5 times (the green status light
will light then continue flashing, indicating learn mode)
3. Let go of the SET button
4. Press a button on the wireless transmitter
5. The orange LIMIT ERROR light will flash to acknowledge the learned device
6. Press another button until all buttons and/or devices are learned
7. Press STOP button on the GRIFCO front panel to exit learn mode
1. Introduction
This transmitter is for use with Grifco commercial door operators with Security+ 2.0 radio-
on-board or legacy Security+ systems. The door opener activates on button press.
Grifco C10A (Security +2.0)
Wall Control
1. UP - Moves the door upwards
2. DOWN - Moves the door
downwards
3. STOP - Stops the door
4. SET - SET button
5. POWER ON - Shows when
the unit is mains powered
6. STATUS - Shows the status of
the unit
7. LIMIT ERROR – When lit
indicates limits are not set
The wireless transmitter can be
used to TOGGLE the action of the
door between close / stop / open
if an obstruction detection device
is installed, or stop / open only if
no obstruction detection device is
installed.
1
5
7
2
6
4
3
One Year Limited Warranty
Chamberlain warrants to the original purchaser of this product that it is free
from defect in materials and/or workmanship for a period of 1 year from the
date of purchase.
Note: Batteries are not covered by warranty

3. Programming other Security +2.0 Systems
The transmitter is preset for use with Grifco Security +2.0 systems (for example eDrive
+2.0 Commercial Door Openers). Refer to the WIRELESS PROGRAMMING section in your
operator manual for detailed instructions on programming.
4. Programming STAR1000EVO
The STAR1000EVO transmitter management device has the
ability to learn a combination of remote control transmitters
and keyless entries up to 1,000 devices. Audible and visual
warnings occur when the receiver capacity is exceeded.
View the STAR1000EVO user manual for details of
programming and managing transmitters with this device.
5. Programming Older (Legacy or Security+) Systems
To program the transmitter for legacy Security+ systems (for example original eDrive,
Maestro with MRC receiver card), the transmitter must first be placed into TRANSMITTER
PROGRAMMING mode.
1. Enter TRANSMITTER PROGRAMMING mode on the transmitter by pressing & holding
the left & right buttons simultaneously for 5 seconds (fig 1). Release when the
transmitter LED stays ON continuously
2. Press & release the LEARN button on the operator (fig 2). Within 30 seconds, the
transmitter can now be programmed
3. Press & release the desired button on the transmitter (fig 3). If the operator light
flashes, the code has been learned & step 4 can be performed. If not, press the
selected button again until the operator indicates the code has been learned.
4. Press & release any one of the OTHER 3 buttons of the transmitter (fig 4). This LOCKS
the code into the button selected in step 3 & the transmitter LED turns OFF.
The code has been learned & the transmitter will operate the door on the next press.
NOTE: In the event you need to return a button to Security +2.0 code, repeat the
programming sequence outlined above.
S-Drive
Main Control Board
1. Press the dedicated LEARN button
on the main control board
2. Press the desired door operation
(OPEN, CLOSE or STOP)
3. Press the transmitter button. One
transmitter button can also be set
to toggle Open, Stop and Close.
See operator manual for details
L-Drive SDO
Control Panel
1. Press and hold the desired button
on the transmitter
2. Press the LEARN button on the rear
of the opener
3. Release the button on the transmitter
See operator manual for details
eDrive +2.0 MCB
(inc. GLMe2 Logic Upgrade)
1. Press the dedicated LEARN
button on the main control board
2. Press the desired transmitter button
Transmitter can be programmed to
perform different tasks
3. Press the dedicated LEARN button
again to exit learn mode
See operator manual for details
1 2 3 4
Press & hold both left
& right buttons on the
transmitter
With an MRC2 installed in
the operator:
• Press / hold SET
• Press STOP 5 times
Press & release the
desired button on
the transmitter
Press & release one
of the OTHER 3
buttons
Learn
Learn
SET
STOP
6. Replacing Batteries
The lithium battery should produce power for up to 5
years. If battery power is low the LEDs will not flash when a
button is pressed.
1 2 3 4
Open case with
screwdriver
Remove &
dispose of old
battery properly
Insert new
CR2032
battery, positive
side up
Replace cover
with screwdriver
114A4931B








