Grizzly G0936 User manual

COPYRIGHT © NOVEMBER, 2021 BY GRIZZLY INDUSTRIAL, INC.
WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.
#CS21947 PRINTED IN TAIWAN V1.11.21
MODEL G0936
20" VERTICAL OSCILLATING
BELT SANDER
OWNER'S MANUAL
(For models manufactured since 06/21)

This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.

Table of Contents
INTRODUCTION............................................... 2
Contact Info.................................................... 2
Manual Accuracy ........................................... 2
Identification ................................................... 3
Controls & Components ................................. 4
Machine Data Sheet ...................................... 5
SECTION 1: SAFETY....................................... 7
Safety Instructions for Machinery .................. 7
Additional Safety for Belt Sanders ................. 9
SECTION 2: POWER SUPPLY ...................... 10
SECTION 3: SETUP ....................................... 12
Unpacking .................................................... 12
Needed for Setup ......................................... 12
Inventory ...................................................... 13
Cleanup ........................................................ 13
Site Considerations ...................................... 14
Assembly ..................................................... 15
Anchoring to Floor ....................................... 15
Dust Collection ............................................. 16
Test Run ...................................................... 16
SECTION 4: OPERATIONS ........................... 17
Operation Overview ..................................... 17
Disabling & Locking Switch.......................... 18
Workpiece Inspection................................... 18
Sanding Tips ................................................ 19
Choosing Sanding Belts .............................. 19
Installing/Changing Sanding Belt ................. 20
Tensioning Sanding Belt .............................. 21
Adjusting Miter Gauge Angle ....................... 21
Adjusting Platen Tilt ..................................... 22
Edge & End Sanding ................................... 22
Bevel Sanding .............................................. 23
SECTION 5: ACCESSORIES ......................... 24
SECTION 6: MAINTENANCE......................... 25
Schedule ...................................................... 25
Cleaning & Protecting .................................. 25
Lubrication ................................................... 26
Checking & Replacing V-Belt....................... 27
SECTION 7: SERVICE ................................... 28
Troubleshooting ........................................... 28
Adjusting Oscillation Timing & Speed .......... 30
Squaring Platen to Table ............................. 31
Adjusting 45° Stop ....................................... 32
Calibrating Platen Angle Scale .................... 33
Calibrating Miter Gauge Scale ..................... 34
Adjusting Miter Gauge Stops ....................... 34
SECTION 8: WIRING...................................... 35
Wiring Safety Instructions ............................ 35
Wiring Diagram ............................................ 36
Electrical Component Photos ...................... 37
SECTION 9: PARTS....................................... 39
Cabinet ......................................................... 39
Lower Roller ................................................. 41
Upper Roller ................................................. 43
Electrical Box ............................................... 45
Miter Gauge ................................................. 47
Labels & Cosmetics ..................................... 48
WARRANTY & RETURNS ............................. 49

-2- Model G0936 (Mfd. Since 06/21)
We stand behind our machines! If you have ques-
tions or need help, contact us with the information
below. Before contacting, make sure you get the
serial number
and manufacture date from the
machine ID label. This will help us help you faster.
Grizzly Technical Support
1815 W. Battlefield
Springfield, MO 65807
Phone: [phone]
Email: [email protected]
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
Contact Info
We are proud to provide a high-quality owner’s
manual with your new machine!
We
made every effort to be exact with the
instruc-
tions, specifications, drawings, and photographs
in this manual. Sometimes we make mistakes, but
our policy of continuous improvement also means
that
sometimes the machine
you receive is
slightly different than shown in the manual
.
If you find this to be the case, and the difference
between the manual and machine leaves you
confused or unsure about something
,
check our
website for an updated version. W
e post
current
manuals and
manual updates for free
on our web-
site at
www.grizzly.com.
Alternatively, you can call our Technical Support
for help. Before calling, make sure you write
down the
manufacture date and
serial number
from the machine ID label (see below). This
information is required for us to provide proper
tech support, and it helps us determine if updated
documentation is available for your machine.
Manufacture Date
Serial Number
Manual Accuracy
INTRODUCTION

Model G0936 (Mfd. Since 06/21) -3-
Become familiar with the names and locations of the controls and features shown below to better understand
the instructions in this manual.
Identification
For Your Own Safety Read Instruction Manual Before Operating Sander
a) Wear eye protection.
b) Support workpiece with miter gauge or worktable.
c) Maintain 1⁄16 in. maximum clearance between table and sanding belt.
Like all machinery there is potential danger
when operating this machine. Accidents
are frequently caused by lack of familiarity
or failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety pre-
cautions are overlooked or ignored, seri-
ous personal injury may occur.
No list of safety guidelines can be com-
plete. Every shop environment is different.
Always consider safety first, as it applies
to your individual working conditions. Use
this and other machinery with caution and
respect. Failure to do so could result in
serious personal injury, damage to equip-
ment, or poor work results.
Table
Cabinet
Door
Sanding
Belt
Belt Tension
Lock Handle
ON/OFF
Buttons
Platen Tilt
Handwheel
Platen Tilt
Angle Scale
4" Dust
Port
Belt Tension
Handwheel
Sanding Belt Cover
Lock Knob
(1 of 2)
Electrical
Box
Platen
Sanding Belt
Cover

-4- Model G0936 (Mfd. Since 06/21)
Controls &
Components
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
Refer to the following figures and descriptions to
become familiar with the basic controls and com-
ponents of this machine. Understanding these
items and how they work will help you understand
the rest of the manual and minimize your risk of
injury when operating this machine.
A. Platen Tilt Angle Scale: Displays platen tilt.
B. Platen Tilt Handwheel: Adjusts platen tilt
from 0°–45°.
C. ON/OFF Buttons: ON button turns motor
ON and can be locked to prevent accidental
startup. OFF button turns motor OFF.
D. Platen Tilt Lock Knob: Loosens to adjust
platen tilt and tightens to lock platen position.
Cabinet Components
Figure 1. Cabinet controls and components.
A
BC
Sanding Components
E. Belt Tension Handwheel: Adjusts sanding
belt tension to allow for service and removal.
F. Platen: Provides belt support for flat sanding
surface.
G. Belt Tension Lock Handle: Loosens to
adjust sanding belt tension and tightens to
lock belt tension.
Figure 2. Front sanding components.
EF
G
H. Sanding Belt Cover Lock Knobs: Loosen
to remove sanding belt cover for service or to
change belt. Tighten to secure cover.
I. Table: Supports workpiece against sanding
belt and provides T-slot tracks for included
miter gauge.
Figure 3. Sanding controls and components.
H
I
D

Model G0936 (Mfd. Since 06/21) -5-
The information contained herein is deemed accurate as of 12/1/2021 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2
Model G0936
MACHINE DATA
SHEET
Customer Service #: [phone] · To Order Call: [phone] · Fax #: [phone]
MODEL G0936 20" VERTICAL OSCILLATING BELT SANDER
Product Dimensions:
Weight.............................................................................................................................................................. 362 lbs.
Width (side-to-side) x Depth (front-to-back) x Height........................................................ 31-1/2 x 27-1/2 x 54-1/2 in.
Footprint (Length x Width)..................................................................................................................... 26-1/2 x 17 in.
Shipping Dimensions:
Type.......................................................................................................................................................... Wood Crate
Content........................................................................................................................................................... Machine
Weight.............................................................................................................................................................. 407 lbs.
Length x Width x Height....................................................................................................................... 38 x 29 x 64 in.
Must Ship Upright................................................................................................................................................... Yes
Electrical:
Power Requirement........................................................................................................... 220V, Single-Phase, 60 Hz
Full-Load Current Rating................................................................................................................................... 10.55A
Minimum Circuit Size.............................................................................................................................................. 15A
Connection Type....................................................................................................................................... Cord & Plug
Power Cord Included.............................................................................................................................................. Yes
Power Cord Length.............................................................................................................................................. 72 in.
Power Cord Gauge......................................................................................................................................... 14 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................................ 6-15
Switch Type................................................................................................................................ ON/OFF Push Button
Motors:
Main
Horsepower................................................................................................................................................ 2 HP
Phase............................................................................................................................................ Single-Phase
Amps............................................................................................................................................................ 10A
Speed................................................................................................................................................ 3450 RPM
Type................................................................................................................................. TEFC Capacitor Start
Power Transfer ............................................................................................................................................ Belt
Bearings..................................................................................................... Shielded & Permanently Lubricated
Centrifugal Switch/Contacts Type.......................................................................................................... Internal
Oscillation
Horsepower................................................................................................................................................. 37W
Phase............................................................................................................................................ Single-Phase
Amps......................................................................................................................................................... 0.55A
Speed.................................................................................................................................................... 60 RPM
Type.......................................................................................................................................................... TEFC
Power Transfer .......................................................................................................................................... Gear
Bearings..................................................................................................... Shielded & Permanently Lubricated
Machine Data Sheet

-6- Model G0936 (Mfd. Since 06/21)
The information contained herein is deemed accurate as of 12/1/2021 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 2 OF 2
Model G0936
Main Specifications:
Operation Information
Sanding Belt Speed........................................................................................................................... 1350 FPM
Sanding Belt Oscillations............................................................................................................................. 1 in.
Sanding Belt Length............................................................................................................................ 41-1/2 in.
Sanding Belt Width.............................................................................................................................. 19-5/8 in.
Sanding Belt Tilt................................................................................................................................ 0 - 45 deg.
Table Information
Table Length........................................................................................................................................ 11-3/4 in.
Table Width......................................................................................................................................... 29-5/8 in.
Table Thickness.................................................................................................................................... 1-1/2 in.
Floor To Table Height.......................................................................................................................... 35-3/4 in.
Platen Information
Platen Type.............................................................................................................................. Graphite-Coated
Platen Length...................................................................................................................................... 12-1/4 in.
Platen Width.............................................................................................................................................. 22 in.
Construction
Table.................................................................................................................................................... Cast Iron
Frame......................................................................................................................................................... Steel
Base........................................................................................................................................................... Steel
Drive Roller............................................................................................................................................. Rubber
Idler Roller.......................................................................................................................................... Aluminum
Paint Type/Finish....................................................................................................................... Powder Coated
Other Related Information
Number of Dust Ports....................................................................................................................................... 1
Dust Port Size.............................................................................................................................................. 4 in.
Belt Release..................................................................................................................................... Handwheel
Drive Roller Size.................................................................................................................................... 3-1/4 in.
Idler Roller Size..................................................................................................................................... 3-1/4 in.
Other Specifications:
Country of Origin .............................................................................................................................................. Taiwan
Warranty ........................................................................................................................................................... 1 Year
Serial Number Location .................................................................................................................................. ID Label
Sound Rating ................................................................................................................................................ 83-85 dB
Features:
Handwheel-Adjusted Belt Tension
Synchronous Belt Drive
Limit Switch-Operated Belt Oscillation
Graphite-Coated Platen
Platen Tilts 0 to 45 Degrees
T-Slot Table and Miter Gauge

Model G0936 (Mfd. Since 06/21) -7-
ELECTRICAL EQUIPMENT INJURY RISKS.
You can be shocked, burned, or killed by touching
live electrical components or improperly grounded
machinery. To reduce this risk, only allow qualified
service personnel to do electrical installation or
repair work, and always disconnect power before
accessing or exposing electrical equipment.
DISCONNECT POWER FIRST.
Always discon-
nect machine from power supply BEFORE mak-
ing adjustments, changing tooling, or servicing
machine. This prevents an injury risk from unin-
tended startup or contact with live electrical com-
ponents.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are NOT approved safety glasses.
OWNER’S MANUAL. Read and understand this
owner’s manual BEFORE using machine.
TRAINED OPERATORS ONLY. Untrained oper-
ators have a higher risk of being hurt or killed.
Only allow trained/supervised people to use this
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machine to prevent unauthorized use—especially
around children. Make your workshop kid proof!
DANGEROUS ENVIRONMENTS. Do not use
machinery in areas that are wet, cluttered, or have
poor lighting. Operating machinery in these areas
greatly increases the risk of accidents and injury.
MENTAL ALERTNESS REQUIRED. Full mental
alertness is required for safe operation of machin-
ery. Never operate under the influence of drugs or
alcohol, when tired, or when distracted.
For Your Own Safety, Read Instruction
Manual Before Operating This Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures. Always use common sense and good judgment.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
Alerts the user to useful information about proper operation of the
machine to avoid machine damage.
NOTICE
Safety Instructions for Machinery
SECTION 1: SAFETY

-8- Model G0936 (Mfd. Since 06/21)
WEARING PROPER APPAREL. Do not wear
clothing, apparel or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to reduce
risk of slipping and losing control or accidentally
contacting cutting tool or moving parts.
HAZARDOUS DUST. Dust created by machinery
operations may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece mate-
rial. Always wear a NIOSH-approved respirator to
reduce your risk.
HEARING PROTECTION. Always wear hear-
ing protection when operating or observing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
REMOVE ADJUSTING TOOLS. Tools left on
machinery can become dangerous projectiles
upon startup. Never leave chuck keys, wrenches,
or any other tools on machine. Always verify
removal before starting!
USE CORRECT TOOL FOR THE JOB. Only use
this tool for its intended purpose—do not force
it or an attachment to do a job for which it was
not designed. Never make unapproved modifica-
tions—modifying tool or using it differently than
intended may result in malfunction or mechanical
failure that can lead to personal injury or death!
AWKWARD POSITIONS. Keep proper footing
and balance at all times when operating machine.
Do not overreach! Avoid awkward hand positions
that make workpiece control difficult or increase
the risk of accidental injury.
CHILDREN & BYSTANDERS. Keep children and
bystanders at a safe distance from the work area.
Stop using machine if they become a distraction.
GUARDS & COVERS. Guards and covers reduce
accidental contact with moving parts or flying
debris. Make sure they are properly installed,
undamaged, and working correctly BEFORE
operating machine.
FORCING MACHINERY. Do not force machine.
It will do the job safer and better at the rate for
which it was designed.
NEVER STAND ON MACHINE. Serious injury
may occur if machine is tipped or if the cutting
tool is unintentionally contacted.
STABLE MACHINE. Unexpected movement dur-
ing operation greatly increases risk of injury or
loss of control. Before starting, verify machine is
stable and mobile base (if used) is locked.
USE RECOMMENDED ACCESSORIES. Consult
this owner’s manual or the manufacturer for rec-
ommended accessories. Using improper acces-
sories will increase the risk of serious injury.
UNATTENDED OPERATION. To reduce the
risk of accidental injury, turn machine OFF and
ensure all moving parts completely stop before
walking away. Never leave machine running
while unattended.
MAINTAIN WITH CARE. Follow all maintenance
instructions and lubrication schedules to keep
machine in good working condition. A machine
that is improperly maintained could malfunction,
leading to serious personal injury or death.
DAMAGED PARTS. Regularly inspect machine
for damaged, loose, or mis-adjusted parts—or
any condition that could affect safe operation.
Immediately repair/replace BEFORE operating
machine. For your own safety, DO NOT operate
machine with damaged parts!
MAINTAIN POWER CORDS. When disconnect-
ing cord-connected machines from power, grab
and pull the plug—NOT the cord. Pulling the cord
may damage the wires inside. Do not handle
cord/plug with wet hands. Avoid cord damage by
keeping it away from heated surfaces, high traffic
areas, harsh chemicals, and wet/damp locations.
EXPERIENCING DIFFICULTIES. If at any time
you experience difficulties performing the intend-
ed operation, stop using the machine! Contact our
Technical Support at [phone].

Model G0936 (Mfd. Since 06/21) -9-
Additional Safety for Belt Sanders
Serious injury or death can occur from fingers, clothing, jewelry, or hair getting pinched/
entangled in belt or other moving components. Abrasion injuries can occur from touching
moving sandpaper with bare skin. Workpieces thrown by sanding surface can strike operator
or bystanders with moderate force, causing impact injuries. Long-term respiratory damage can
occur from using sander without proper use of a respirator. To reduce the risk of these hazards,
operator or bystanders MUST completely heed the hazards and warnings below.
WORKPIECE SUPPORT. Workpiece kickback
can occur with violent force if workpiece is not
properly supported during operation. Always sand
with workpiece firmly against table or another sup-
port device.
SANDING DUST. Sanding creates large amounts
of dust that can lead to eye injury or respira-
tory illness. Reduce your risk by always wearing
approved eye and respiratory protection when
using sander. Never operate without adequate
dust collection system in place and running.
However, dust collection is not a substitute for
using a respirator.
WORKPIECE INSPECTION. Nails, staples, knots,
or other imperfections in workpiece can be dis-
lodged and thrown from sander at a high rate of
speed at people, or cause damage to sandpaper
or sander. Never sand stock that has embedded
foreign objects or questionable imperfections.
SANDPAPER CONDITION. Worn or damaged
sandpaper can fly apart and throw debris at opera-
tor, or aggressively grab workpiece, resulting in
subsequent injuries from operator loss of work-
piece control. Always inspect sandpaper before
operation and replace if worn or damaged.
WORKPIECE INTEGRITY. Sanding fragile work-
pieces can result in loss of control, resulting in
abrasion injuries, impact injuries, or damage to
sandpaper. Only sand solid workpieces that can
withstand power sanding forces. Make sure work-
piece shape is properly supported; avoid sanding
workpieces without flat bottom surfaces unless
some type of jig is used to maintain support and
control when sanding force is applied.
SANDPAPER DIRECTION. Feeding workpiece
incorrectly can cause it to be thrown from machine,
striking operator or bystanders, or causing your
hands to slip into the moving sandpaper. To reduce
these risks, only sand against direction of sandpa-
per travel, ensure workpiece is properly supported,
and avoid introducing sharp edges into moving
sandpaper on the leading side of the workpiece.
IN-RUNNING NIP POINTS. The gap between
moving sandpaper and fixed table/support creates
a pinch point for fingers or workpieces; the larger
this gap is, the greater the risk of fingers or work-
pieces getting caught in it. Minimize this risk by
adjusting table/support to no more than 1⁄16" away
from sandpaper.
HAND PLACEMENT. Rotating sandpaper can
remove skin quickly. Always keep hands away
from moving sandpaper during operation. Stop
machine to clean table of sawdust and chips.
MINIMUM STOCK DIMENSION. Small workpiec-
es can be aggressively pulled from your hands,
causing contact with sanding surface. Always use
a jig or other holding device when sanding small
workpieces, and keep hands and fingers at least
2" away from sanding surface.
FEEDING WORKPIECE. Forcefully jamming
workpiece into sanding surface could cause it to
be grabbed aggressively, pulling hands into sand-
ing surface. Firmly grasp workpiece in both hands
and ease it into sandpaper using light pressure.
AVOIDING ENTANGLEMENT. Becoming entan-
gled in moving parts can cause pinching and
crushing injuries. To avoid these hazards, keep all
guards in place and closed. DO NOT wear loose
clothing, gloves, or jewelry, and tie back long hair.

-10- Model G0936 (Mfd. Since 06/21)
SECTION 2: POWER SUPPLY
Availability
Before installing the machine, consider the avail-
ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocution,
fire, or equipment damage, installation work and
electrical wiring must be done by an electrician or
qualified service personnel in accordance with all
applicable codes and standards.
Electrocution, fire, shock,
or equipment damage
may occur if machine is
not properly grounded
and connected to power
supply.
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
Full-Load Current Rating.............. 10.55 Amps
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over-
loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the specified circuit requirements.
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
Note: Circuit requirements in this manual apply to
a dedicated circuit—where only one machine will
be running on the circuit at a time. If machine will
be connected to a shared circuit where multiple
machines may be running at the same time, con-
sult an electrician or qualified service personnel to
ensure circuit is properly sized for safe operation.
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup-
ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
Circuit Information
Circuit Requirements
This machine is prewired to operate on a power
supply circuit that has a verified ground and meets
the following requirements:
Nominal Voltage ......... 208V, 220V, 230V, 240V
Cycle ..........................................................60 Hz
Phase ........................................... Single-Phase
Power Supply Circuit ......................... 15 Amps
Plug/Receptacle ............................. NEMA 6-15

Model G0936 (Mfd. Since 06/21) -11-
Improper connection of the equipment-grounding
wire can result in a risk of electric shock. The
wire with green insulation (with or without yellow
stripes) is the equipment-grounding wire. If repair
or replacement of the power cord or plug is nec-
essary, do not connect the equipment-grounding
wire to a live (current carrying) terminal.
Check with a qualified electrician or service per-
sonnel if you do not understand these grounding
requirements, or if you are in doubt about whether
the tool is properly grounded. If you ever notice
that a cord or plug is damaged or worn, discon-
nect it from power, and immediately replace it with
a new one.
Extension Cords
We do not recommend using an extension cord
with this machine.
If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
Extension cords cause voltage drop, which can
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
be in good condition and contain a ground wire
and matching plug/receptacle. Additionally, it must
meet the following size requirements:
Minimum Gauge Size ...........................14 AWG
Maximum Length (Shorter is Better).......50 ft.
Figure 4. Typical 6-15 plug and receptacle.
Grounding Pin
Current Carrying Prongs
6-15 PLUG
GROUNDED
6-15 RECEPTACLE
Grounding Requirements
This machine MUST be grounded. In the event
of certain malfunctions or breakdowns, grounding
reduces the risk of electric shock by providing a
path of least resistance for electric current.
This machine is equipped with a power cord that
has an equipment-grounding wire and a grounding
plug. Only insert plug into a matching receptacle
(outlet) that is properly installed and grounded in
accordance with all local codes and ordinances.
DO NOT modify the provided plug!
No adapter should be used with plug. If
plug does not fit available receptacle, or if
machine must be reconnected for use on a
different type of circuit, reconnection must
be performed by an electrician or qualified
service personnel, and it must comply with
all local codes and ordinances.
Serious injury could occur if you connect
machine to power before completing setup
process. DO NOT connect to power until
instructed later in this manual.

-12- Model G0936 (Mfd. Since 06/21)
SECTION 3: SETUP
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
Wear safety glasses during
the entire setup process!
HEAVY LIFT!
Straining or crushing injury
may occur from improperly
lifting machine or some of
its parts. To reduce this risk,
get help from other people
and use a forklift (or other
lifting equipment) rated for
weight of this machine.
Description Qty
• Disposable Rags/Gloves ............ As Needed
• Cleaner/Degreaser ..................... As Needed
• Safety Glasses (Each Person) ............1 Pair
• Lifting Equipment (Rated for 450 lbs.) ........ 1
• Mounting Hardware .................... As Needed
• Dust Collection System .............................. 1
• Dust Hose 4" .............................................. 1
• Hose Clamp 4" ........................................... 1
Needed for Setup
The following items are needed, but not included,
for the setup/assembly of this machine.
This machine was carefully packaged for safe
transport. When unpacking, separate all enclosed
items from packaging materials and inspect them
for shipping damage.
If items are damaged
,
please
call us immediately at [phone].
IMPORTANT:
Save all packaging materials until
you are completely satisfied with the machine and
have resolved any issues between Grizzly or the
shipping agent. You MUST have the original pack-
aging to file a freight claim. It is also extremely
helpful if you need to return your machine later.
Unpacking

Model G0936 (Mfd. Since 06/21) -13-
Figure 5. Loose inventory.
NOTICE
If you cannot find an item on this list, care-
fully check around/inside the machine and
packaging materials. Often, these items get
lost in packaging materials while unpack-
ing or they are pre-installed at the factory.
Inventory
The following is a list of items shipped with your
machine. Before beginning setup, lay these items
out and inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Inventory (Figure 5) Qty
A. Miter Gauge ................................................ 1
B. Hex Wrenches 4, 5, 6mm .....................1 Ea.
C. Open-Ends Wrench 12 x 14mm ................. 1
D. Handwheel Handle ..................................... 1
Cleanup
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
There are many ways to remove this rust preven-
tative, but the following steps work well in a wide
variety of situations. Always follow the manufac-
turer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
Before cleaning, gather the following:
• Disposable rags
• Cleaner/degreaser (WD•40 works well)
• Safety glasses & disposable gloves
• Plastic paint scraper (optional)
Basic steps for removing rust preventative:
1.
Put on safety glasses.
2. Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
3.
Wipe off the surfaces. If your cleaner/degreas-
er is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.
4.
Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
NOTICE
Avoid harsh solvents like acetone or brake
parts cleaner that may damage painted sur-
faces. Always test on a small, inconspicu-
ous location first.
AB
CD

-14- Model G0936 (Mfd. Since 06/21)
Site Considerations
Figure 6. Minimum working clearances.
Electrical
Connection
=
31½"
Min. 30"
for Maintenance
Wall
41½"
Weight Load
Refer to the
Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest work-
piece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the main-
tenance and service described in this manual.
See below for required space allocation.
Physical Environment
The physical environment where the machine is
operated is important for safe operation and lon-
gevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemi-
cals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 20%–95% (non-condensing); or
the environment is subject to vibration, shocks,
or bumps.
Electrical Installation
Place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals, or
other hazards. Make sure to leave enough space
around machine to disconnect power supply or
apply a lockout/tagout device, if required.
Lighting
Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.

Model G0936 (Mfd. Since 06/21) -15-
Figure 8. Handwheel handle installed.
Assembly Anchoring to Floor
Anchoring machinery to the floor prevents tipping
or shifting and reduces vibration that may occur
during operation, resulting in a machine that runs
slightly quieter and feels more solid.
If the machine will be installed in a commercial or
workplace setting, or if it is permanently connect-
ed (hardwired) to the power supply, local codes
may require that it be anchored to the floor.
If not required by any local codes, fastening the
machine to the floor is an optional step. If you
choose not to do this with your machine, we rec-
ommend placing it on machine mounts, as these
provide an easy method for leveling and they have
vibration-absorbing pads.
Lag shield anchors with lag screws (see below)
are a popular way to anchor machinery to a con-
crete floor, because the anchors sit flush with the
floor surface, making it easy to unbolt and move
the machine later, if needed. However, anytime
local codes apply, you MUST follow the anchoring
methodology specified by the code.
Machine Base
Concrete
Lag Screw
Lag Shield Anchor
Flat Washer
Drilled Hole
Figure 9. Popular method for anchoring
machinery to a concrete floor.
Anchoring to Concrete Floors
Number of Mounting Holes ............................ 4
Diameter of Mounting Hardware................ 5⁄16"
5. Lift machine just enough to clear pallet, then
remove pallet and lower machine to ground.
6. Install handwheel handle in handwheel, as
shown in Figure 8.
The machine must be fully assembled before it
can be operated. Before beginning the assembly
process, refer to
Needed for Setup
and gather
all
listed items.
To ensure the assembly process
goes smoothly, first clean any
parts that are
cov-
ered or coated in heavy-duty rust preventative (if
applicable).
Handwheel
To assemble machine:
1. Remove crate top and sides, then remove
any small components from shipping pallet.
2. Move machine to prepared location while it is
still attached to shipping pallet.
3. Remove straps securing machine to pallet.
4. Carefully place forklift forks under sander
(see Figure 7).
Figure 7. Lifting locations.

-16 - Model G0936 (Mfd. Since 06/21)
Figure 10. Dust hose attached to dust port.
Dust Collection
To connect dust collection system to machine:
1. Fit 4" dust hose over dust port, as shown in
Figure 10, and secure in place with hose
clamp.
Minimum CFM at Dust Port: 400 CFM
Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust col-
lector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to cal-
culate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.
This machine creates a lot of wood chips/
dust during operation. Breathing airborne
dust on a regular basis can result in perma-
nent respiratory illness. Reduce your risk
by wearing a respirator and capturing the
dust with a dust-collection system.
2. Tug hose to make sure it does not come off.
Note: A tight fit is necessary for proper
performance.
Test Run
Once assembly is complete, test run the machine
to ensure it is properly connected to power and
safety components are functioning correctly.
If you find an unusual problem during the test run,
immediately stop the machine, disconnect it from
power, and fix the problem BEFORE operating the
machine again. The
Troubleshooting
table in the
SERVICE section of this manual can help.
DO NOT start machine until all preceding
setup instructions have been performed.
Operating an improperly set up machine
may result in malfunction or unexpect-
ed results that can lead to serious injury,
death, or machine/property damage.
Serious injury or death can result from
using this machine BEFORE understanding
its controls and related safety information.
DO NOT operate, or allow others to operate,
machine until the information is understood.
To test run machine:
1. Clear all setup tools away from machine.
2. Connect machine to power supply.
3. Turn machine ON to verify motor operation,
then turn machine OFF. A correctly operat-
ing machine will run smoothly with little or no
vibration or rubbing noises.
— If machine runs smoothly, congratulations,
the Test Run is complete!
— If machine does not run smoothly, imme-
diately turn machine OFF and call Tech
Support for help.
The Test Run consists of verifying the following: 1)
The motor powers up and runs correctly.

Model G0936 (Mfd. Since 06/21) -17-
SECTION 4: OPERATIONS
Operation Overview
The purpose of this overview is to provide the nov-
ice machine operator with a basic understanding
of how the machine is used during operation, so
the
machine controls/components
discussed later
in this manual
are easier to understand.
Due to the generic nature of this overview, it is
not intended to be an instructional guide. To learn
more about specific operations, read this entire
manual,
seek additional
training from experienced
machine operators
, and do additional research
outside of this manual by reading "how-to" books,
trade magazines, or websites.
To complete a typical operation, the operator
does the following:
1. Examines the workpiece to verify it is suitable
for sanding.
2. Prepares and trims workpiece as necessary.
3. Installs sanding belt with appropriate grit for
operation.
4. Adjusts platen tilt as desired, then adjusts
table to allow maximum 1⁄16" clearance
between table and sandpaper.
5. Ties back loose hair and clothing, and puts
on safety glasses and respirator. Takes all
other required safety precautions.
6. Starts dust collector and then sander.
7. With both hands, holds workpiece firmly
against table and miter gauge (if used), eases
workpiece into sanding belt, and moves
workpiece back and forth to wear sandpaper
evenly and prevent overheating.
8. Turns machine and dust collector OFF.
To reduce your risk of
serious injury, read this
entire manual BEFORE
using machine.
To reduce risk of eye injury from flying
chips or lung damage from breathing dust,
always wear safety glasses and a respirator
when operating this machine.
If you are not experienced with this type
of machine, WE STRONGLY RECOMMEND
that you seek additional training outside of
this manual. Read books/magazines or get
formal training before beginning any proj-
ects. Regardless of the content in this sec-
tion, Grizzly Industrial will not be held liable
for accidents caused by lack of training.
Keep hair, clothing, and
jewelry away from mov-
ing parts at all times.
Entanglement can result
in death, amputation, or
severe crushing injuries!

-18- Model G0936 (Mfd. Since 06/21)
NOTICE
The padlock shaft diameter is important to
the disabling function of the switch. With
any padlock used to lock the switch, test
the switch after installation to ensure that it
is properly disabled.
Children or untrained people can be
seriously injured by this machine
. This
risk increases with unsupervised operation.
To help prevent unsupervised operation,
disable and lock the switch before leaving
machine unattended! Place key in a well-
hidden or secure location.
Figure 12. Minimum lock shaft requirements.
Disabling & Locking
Switch
Figure 11. Switch disabled by a padlock.
The ON/OFF switch can be disabled and locked
by inserting a padlock through the ON button,
as shown. Locking the switch in this manner can
prevent unauthorized operation of the machine,
which is especially important if the machine is not
stored inside an access-restricted building.
IMPORTANT:
Locking the switch with a padlock
only restricts its function. It is not a substitute
for disconnecting power from the machine when
adjusting or servicing.
Shaft
Padlock
Workpiece
Inspection
Some workpieces are not safe to sand or may
require modification before they are safe to sand.
Before sanding, inspect all workpieces for the
following:
• Material Type: This machine is intended for
sanding natural and man-made wood prod-
ucts. This machine is NOT designed to sand
metal, glass, stone, tile, plastics, drywall,
cement backer board, laminate products, etc.
Sanding improper materials increases risk of
respiratory harm to operator and bystanders
due to especially fine dust inherently created
by all types of sanding operations—even
if a dust collector is used. Additionally, life
of machine and sanding belts will be great-
ly reduced (or immediately damaged) from
sanding improper materials or from exposure
to fine dust created when doing so.
• Foreign Objects: Nails, staples, dirt, rocks
and other foreign objects are often embed-
ded in wood. While sanding, these objects
can become dislodged and tear sanding belt
Always visually inspect your workpiece for
these items. If they cannot be removed, DO
NOT sand the workpiece.
• Wet or "Green" Stock: Sanding wood with a
moisture content over 20% causes unneces-
sary clogging and wear on the sanding belt,
increases the risk of kickback, and yields
poor results.
• Excessive Glue or Finish: Sanding
workpieces with excess glue or finish will load
up the abrasive, reducing its usefulness and
lifespan.