Grizzly GO739 User manual

MODEL G0739
OSCILLATING SPINDLE SANDER
OWNER'S MANUAL
(For models manufactured since 2/12)

WARNING: NO PORTION OF THIS MANUAL MAY BE REPRODUCED IN ANY SHAPE
OR FORM WITHOUT THE WRITTEN APPROVAL OF GRIZZLY INDUSTRIAL, INC.


This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.

Table of Contents
INTRODUCTION............................................... 2
 
 
 
SECTION 1: SAFETY....................................... 5
 
SECTION 2: POWER SUPPLY ........................ 8
 
 
 
 
 
SECTION 3: SETUP ....................................... 10
 
 
 
 
 
 
 
 
 
 
 
 
SECTION 4: OPERATIONS ........................... 16
 
 
 
SECTION 5: ACCESSORIES......................... 18
SECTION 6: MAINTENANCE......................... 19
 
 
 
 
 
SECTION 7: SERVICE ................................... 20
 
 
SECTION 8: WIRING...................................... 22
 
 
SECTION 9: PARTS....................................... 24
 
 
WARRANTY & RETURNS ............................. 29

 
INTRODUCTION
We are proud to offer this manual with your new
machine! We've made every effort to be exact
with the instructions, specifications, drawings,
and photographs of the machine we used when
writing this manual. However, sometimes we still
make an occasional mistake.
Also, owing to our policy of continuous improve-
ment, your machine may not exactly match the
manual. If you find this to be the case, and the dif-
ference between the manual and machine leaves
you in doubt, check our website for the latest
manual update or call technical support for help.
Before calling, find the manufacture date of your
machine by looking at the date stamped into the
machine ID label (see below). This will help us
determine if the manual version you received
matches the manufacture date of your machine.
For your convenience, we post all available man-
uals and manual updates for free on our website
at www.grizzly.com. Any updates to your model
of machine will be reflected in these documents
as soon as they are complete.
Manufacture Date
of Your Machine
Manual Accuracy
We stand behind our machines. If you have
any questions or need help, use the information
below to contact us. Before contacting, please get
the serial number and manufacture date of your
machine. This will help us help you faster.
Grizzly Technical Support
1203 Lycoming Mall Circle
Muncy, PA 17756
Phone: [phone]
Email: [email protected]
We want your feedback on this manual. What did
you like about it? Where could it be improved?
Please take a few minutes to give us feedback.
Grizzly Documentation Manager
P.O. Box 2069
Bellingham, WA 98227-2069
Email: [email protected]
Contact Info

 
Figure 1. 
Identification
















For Your Own Safety Read This Manual
Before Operating Spindle Sander
a) Wear eye protection.
b) Support workpiece on worktable.
c) Minimize pinch hazards. Use the smallest
table insert possible with sanding drum.
d) Avoid kickback. Feed workpiece against
rotation of drum.
e) Avoid entanglement with spinning drum.
Do not wear gloves, necktie, or loose
clothing. Tie back long hair.

 
The information contained herein is deemed accurate as of 2/24/2012 and represents our most recent product specifications.
Due to our ongoing improvement efforts, this information may not accurately describe items previously purchased. PAGE 1 OF 2Model G0739
MACHINE DATA
SHEET
Customer Service #: [phone] · To Order Call: [phone] · Fax #: [phone]
MODEL G0739 OSCILLATING SPINDLE SANDER
Product Dimensions:
Weight............................................................................................................................................................... 30 lbs.
Width (side-to-side) x Depth (front-to-back) x Height.................................................. 15-9/16 in. x 14-1/8 in. x 17 in.
Footprint (Length x Width)................................................................................................................ 15-1/2 in. x 14 in.
Shipping Dimensions:
Type............................................................................................................................................................. Cardboard
Content........................................................................................................................................................... Machine
Weight............................................................................................................................................................... 33 lbs.
Length x Width x Height............................................................................................................. 18 in. x 16 in. x 20 in.
Electrical:
Power Requirement........................................................................................................... 120V, Single-Phase, 60 Hz
Minimum Circuit Size.............................................................................................................................................. 15A
Switch........................................................................................................... Paddle ON/OFF Switch w/Disabling Key
Switch Voltage..................................................................................................................................................... 120V
Cord Length............................................................................................................................................................ 6 ft.
Cord Gauge.................................................................................................................................................... 18 AWG
Plug Included.......................................................................................................................................................... Yes
Included Plug Type................................................................................................................................................ 1-15
Motors:
Main
Type........................................................................................................................... Permanent Magnet Motor
Horsepower............................................................................................................................................. 1/2 HP
Voltage....................................................................................................................................................... 120V
Phase............................................................................................................................................ Single-Phase
Amps........................................................................................................................................................... 3.5A
Number of Speeds............................................................................................................................................ 1
Power Transfer ........................................................................................................................................ V-Belt
Bearings............................................................................................................. Sealed and Lubricated for Life
Main Specifications:
Table Info
Table Width......................................................................................................................................... 11-1/2 in.
Table Length.............................................................................................................................................. 15 in.
Table Thickness.................................................................................................................................. 1-5/16 in.
Table Opening............................................................................................................................................. 4 in.
Spindle Info
Spindle Diameter...................................................................................................................................... 1/2 in.
Spindle Lengths..................................................................................................................................... 4-1/2 in.
Spindle Speed.................................................................................................................................. 2,000 RPM
Spindle Oscillation................................................................................................................................. 58 OPM
Stroke Length........................................................................................................................................... 5/8 in.
Drum Info
Sanding Drum Diameters............................................................................................ 1/2, 3/4, 1, 1-1/2, 2, 3 in.
Sanding Drum Length............................................................................................................................ 4-1/2 in.

 
For Your Own Safety, Read Instruction
Manual Before Operating this Machine
The purpose of safety symbols is to attract your attention to possible hazardous conditions.
This manual uses a series of symbols and signal words intended to convey the level of impor-
tance of the safety messages. The progression of symbols is described below. Remember that
safety messages by themselves do not eliminate danger and are not a substitute for proper
accident prevention measures.
WEARING PROPER APPAREL. Do not wear
clothing, apparel, or jewelry that can become
entangled in moving parts. Always tie back or
cover long hair. Wear non-slip footwear to avoid
accidental slips which could cause a loss of work-
piece control.
HEARING PROTECTION. Always wear hear-
ing protection when operating or observiing loud
machinery. Extended exposure to this noise
without hearing protection can cause permanent
hearing loss.
MENTAL ALERTNESS. Be mentally alert when
running machinery. Never operate under the
influence of drugs or alcohol, when tired, or when
distracted.
OWNER’S MANUAL. Read and understand
this owner’s manual BEFORE using machine.
Untrained users can be seriously hurt.
EYE PROTECTION. Always wear ANSI-approved
safety glasses or a face shield when operating or
observing machinery to reduce the risk of eye
injury or blindness from flying particles. Everyday
eyeglasses are not approved safety glasses.
HAZARDOUS DUST. Dust created while using
machinery may cause cancer, birth defects, or
long-term respiratory damage. Be aware of dust
hazards associated with each workpiece material,
and always wear a NIOSH-approved respirator to
reduce your risk.
Indicates a potentially hazardous situation which, if not avoided,
MAY result in minor or moderate injury. It may also be used to alert
against unsafe practices.
Indicates a potentially hazardous situation which, if not avoided,
COULD result in death or serious injury.
Indicates an imminently hazardous situation which, if not avoided,
WILL result in death or serious injury.
This symbol is used to alert the user to useful information about
proper operation of the machine.
NOTICE
Safety Instructions for Machinery
SECTION 1: SAFETY

 

DISCONNECTING POWER SUPPLY.Alwaysdis-
connect machine from power supply before ser-
vicing, adjusting, or changing cutting tools (bits,
blades,cutters, etc.). Make sure switchisin OFF
positionbeforereconnectingtoavoidanunexpect-
edorunintentionalstart.
APPROVED OPERATION. Untrained operators
can be seriously hurt by machinery. Only allow
trained or properly supervised people to use
machine. When machine is not being used, dis-
connect power, remove switch keys, or lock-out
machinetopreventunauthorizeduse—especially
aroundchildren.Makeworkshopkidproof!
DANGEROUS ENVIRONMENTS. Donotuse
machinery in wet or rainy locations, cluttered
areas,aroundflammables,orindarkareas.Keep
workareaclean,dry,andwell-lighted.
ONLY USE AS INTENDED. Only use machine
for its intended purpose. Never modify machine
forapurposenotintendedbythemanufacturer!
USE RECOMMENDED ACCESSORIES.Consult
thisowner’smanualorthemanufacturerforrec-
ommended accessories. Using improper acces-
sorieswillincreasetheriskofseriousinjury.
CHILDREN & BYSTANDERS. Keepchildren
andbystandersasafedistanceawayfromwork
area.Stopusingmachineifchildrenorbystand-
ersbecomeadistraction.
REMOVE ADJUSTING TOOLS.Neverleave
adjustmenttools,chuckkeys,wrenches,etc.inor
onmachine—especiallynearmovingparts.Verify
removalbeforestarting!
SECURING WORKPIECE. When required, use
clampsorvisestosecureworkpiece.Asecured
workpieceprotectshandsandfreesbothofthem
tooperatethemachine.
FEED DIRECTION.Unlessotherwisenoted,feed
work against the rotation of blades or cutters.
Feedinginthesamedirectionofrotationmaypull
yourhandintothecut.
FORCING MACHINERY.Donotforcemachine.
Itwilldo the job safer and better attheratefor
whichitwasdesigned.
GUARDS & COVERS. Guards and covers can
protect you from accidental contact with moving
parts or flying debris. Make sure they are prop-
erlyinstalled,undamaged, andworkingcorrectly
beforeusingmachine.
NEVER STAND ON MACHINE.Seriousinjuryor
accidental contact with cutting tool may occur if
machineistipped.Machinemaybedamaged.
STABLE MACHINE. Unexpectedmovementdur-
ing operations greatly increases risk of injury or
loss of control. Before starting, verify machines
arestableandmobilebase(ifused)islocked.
AWKWARD POSITIONS. Keep proper footing
andbalanceatalltimeswhenoperatingmachine.
Donotoverreach!Avoidawkwardhandpositions
that make workpiece control difficult or increase
theriskofaccidentalinjury.
UNATTENDED OPERATION. Neverleave
machinerunningwhileunattended.Turnmachine
offandensureallmovingpartscompletelystop
beforewalkingaway.
MAINTAIN WITH CARE.Followallmaintenance
instructions and lubrication schedules to keep
machineingoodworkingcondition.Animproperly
maintainedmachineincreasesriskofinjury.
CHECK DAMAGED PARTS. Regularly inspect
machine for damaged parts, loose bolts, mis-
adjusted or mis-aligned parts, binding, or any
other conditions that may affect safe operation.
Alwaysrepairorreplacedamagedormis-adjust-
edpartsbeforeoperatingmachine.
MAINTAIN POWER CORDS. When disconnect-
ing cord-connected machines frompower,grab
andpulltheplug—NOTthecord.Pullingthecord
maydamage the wires inside. Donothandle
cord/plugwithwethands.Avoidcorddamageby
keepingitawayfromheatedsurfaces,hightraffic
areas,harshchemicals,andwet/damplocations.
EXPERIENCING DIFFICULTIES. Ifatanytime
youare experiencing difficulties performing the
intended operation,stopusingthemachine!
Contactour Technical Support Department at
(570)546-9663.

 
Additional Safety for Spindle Sanders
FEED RATE.


       

AVOIDING ENTANGLEMENT.

       

      

HAND PLACEMENT.     


WORKPIECE HANDLING.   

 
       

SANDING SLEEVES. 
      
        
      

FOREIGN MATERIAL.  



DUST COLLECTION.  
      



DIRECTION.  


POWER DISCONNECT. 

         

RESPIRATOR USE.    
        
        


TABLE INSERTS.     
        
       
       


No list of safety guidelines can be complete.
Every shop environment is different. Always
consider safety first, as it applies to your
individual working conditions. Use this and
other machinery with caution and respect.
Failure to do so could result in serious per-
sonal injury, damage to equipment, or poor
work results.
Like all machinery there is potential danger
when operating this machine. Accidents are
frequently caused by lack of familiarity or
failure to pay attention. Use this machine
with respect and caution to decrease the
risk of operator injury. If normal safety pre-
cautions are overlooked or ignored, serious
personal injury may occur.

 
SECTION 2: POWER SUPPLY
Availability
Before installing the machine, consider the avail-
ability and proximity of the required power supply
circuit. If an existing circuit does not meet the
requirements for this machine, a new circuit must
be installed. To minimize the risk of electrocu-
tion, fire, or equipment damage, installation work
and electrical wiring must be done by a qualified
electrician in accordance with all applicable codes
and standards.
Electrocution, fire, or
equipment damage may
occur if machine is not
correctly grounded and
connected to the power
supply.
Full-Load Current Rating
The full-load current rating is the amperage a
machine draws at 100% of the rated output power.
On machines with multiple motors, this is the
amperage drawn by the largest motor or sum of all
motors and electrical devices that might operate
at one time during normal operations.
Full-Load Current Rating at 120V .... 3.5 Amps
The full-load current is not the maximum amount
of amps that the machine will draw. If the machine
is overloaded, it will draw additional amps beyond
the full-load rating.
If the machine is overloaded for a sufficient length
of time, damage, overheating, or fire may result—
especially if connected to an undersized circuit.
To reduce the risk of these hazards, avoid over-
loading the machine during operation and make
sure it is connected to a power supply circuit that
meets the requirements in the following section.
For your own safety and protection of
property, consult an electrician if you are
unsure about wiring practices or electrical
codes in your area.
Circuit Requirements
Note: The circuit requirements listed in this man-
ual apply to a dedicated circuit—where only one
machine will be running at a time. If this machine
will be connected to a shared circuit where mul-
tiple machines will be running at the same time,
consult a qualified electrician to ensure that the
circuit is properly sized for safe operation.
A power supply circuit includes all electrical
equipment between the breaker box or fuse panel
in the building and the machine. The power sup-
ply circuit used for this machine must be sized to
safely handle the full-load current drawn from the
machine for an extended period of time. (If this
machine is connected to a circuit protected by
fuses, use a time delay fuse marked D.)
This machine is prewired to operate on a 120V
power supply circuit that has a verified ground and
meets the following requirements:
Nominal Voltage ........................................ 120V
Cycle ..........................................................60 Hz
Phase........................................... Single-Phase
Power Supply Circuit ......................... 15 Amps

 
Extension Cords
We do not recommend using an extension cord
with this machine. If you must use an extension
cord, only use it if absolutely necessary and only
on a temporary basis.
Extension cords cause voltage drop, which may
damage electrical components and shorten motor
life. Voltage drop increases as the extension cord
size gets longer and the gauge size gets smaller
(higher gauge numbers indicate smaller sizes).
Any extension cord used with this machine must
contain a ground wire, match the required plug
and receptacle, and meet the following require-
ments:
Minimum Gauge Size ...........................16 AWG
Maximum Length (Shorter is Better).......50 ft.
Serious injury could occur if you connect
the machine to power before completing the
setup process. DO NOT connect to power
until instructed later in this manual.
Polarized Plug
Figure 2. 
5-15 Receptacle
1-15 Plug
Neutral
Hot




          
       



 
SECTION 3: SETUP
       

Description Qty
  
 
 
  
  
  
  
  
  
Needed for Setup
This machine presents
serious injury hazards
to untrained users. Read
through this entire manu-
al to become familiar with
the controls and opera-
tions before starting the
machine!
Wear safety glasses dur-
ing the entire setup pro-
cess!
Your machine was carefully packaged for safe
transportation. Remove the packaging materials
from around your machine and inspect it. If you
discover any damage, please call us immediately
at [phone] for advice.
Save the containers and all packing materials for
possible inspection by the carrier or its agent.
Otherwise, filing a freight claim can be difficult.
When you are completely satisfied with the condi-
tion of your shipment, inventory the contents.
Unpacking
SUFFOCATION HAZARD!
Keep children and pets away
from plastic bags or packing
materials shipped with this
machine. Discard immediately.

 
Inventory
The following is a description of the main compo-
nents shipped with your machine. Lay the compo-
nents out to inventory them.
If any non-proprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
Inventory: (Figure 3) Qty
A. 
B. 

C. 
D. 
E. 

F.  

G.  

H. 
The unpainted surfaces of your machine are
coated with a heavy-duty rust preventative that
prevents corrosion during shipment and storage.
This rust preventative works extremely well, but it
will take a little time to clean.
Be patient and do a thorough job cleaning your
machine. The time you spend doing this now will
give you a better appreciation for the proper care
of your machine's unpainted surfaces.
There are many ways to remove this rust preven-
tative, but the following steps work well in a wide
variety of situations. Always follow the manufac-
turer’s instructions with any cleaning product you
use and make sure you work in a well-ventilated
area to minimize exposure to toxic fumes.
Before cleaning, gather the following:
• Disposable Rags
• Cleaner/degreaser (WD•40 works well)
• Safety glasses & disposable gloves
• Plastic paint scraper (optional)
Basic steps for removing rust preventative:
1. Put on safety glasses.
2. Coat the rust preventative with a liberal
amount of cleaner/degreaser, then let it soak
for 5–10 minutes.
3. Wipe off the surfaces. If your cleaner/degreas-
er is effective, the rust preventative will wipe
off easily. If you have a plastic paint scraper,
scrape off as much as you can first, then wipe
off the rest with the rag.
4. Repeat Steps 2–3 as necessary until clean,
then coat all unpainted surfaces with a quality
metal protectant to prevent rust.
Gasoline or products
with low flash points can
explode or cause fire if
used to clean machin-
ery. Avoid cleaning with
these products.
Many cleaning solvents
are toxic if concentrat-
ed amounts are inhaled.
Only work in a well-venti-
lated area.
NOTICE
Avoid chlorine-based solvents, such as
acetone or brake parts cleaner, that may
damage painted surfaces. Test all cleaners
in an inconspicuous area before using to
make sure they will not damage paint.
Cleanup
NOTICE
If you cannot find an item on this list, care-
fully check the machine and the packaging
materials. Some of these items may be pre-
installed for shipping or become misplaced
during unpacking.
Figure 3. 








 
Site Considerations
Weight Load
Refer to the Machine Data Sheet for the weight
of your machine. Make sure that the surface upon
which the machine is placed will bear the weight
of the machine, additional equipment that may be
installed on the machine, and the heaviest work-
piece that will be used. Additionally, consider the
weight of the operator and any dynamic loading
that may occur when operating the machine.
Space Allocation
Consider the largest size of workpiece that will
be processed through this machine and provide
enough space around the machine for adequate
operator material handling or the installation of
auxiliary equipment. With permanent installations,
leave enough space around the machine to open
or remove doors/covers as required by the main-
tenance and service described in this manual.
See below for required space allocation.
Physical Environment
The physical environment where the machine is
operated is important for safe operation and lon-
gevity of machine components. For best results,
operate this machine in a dry environment that is
free from excessive moisture, hazardous chemi-
cals, airborne abrasives, or extreme conditions.
Extreme conditions for this type of machinery are
generally those where the ambient temperature
range exceeds 41°–104°F; the relative humidity
range exceeds 20–95% (non-condensing); or the
environment is subject to vibration, shocks, or
bumps.
Electrical Installation
Place this machine near an existing power source.
Make sure all power cords are protected from
traffic, material handling, moisture, chemicals,
or other hazards. Make sure to leave access to
a means of disconnecting the power source or
engaging a lockout/tagout device, if required.
Lighting
Lighting around the machine must be adequate
enough that operations can be performed safely.
Shadows, glare, or strobe effects that may distract
or impede the operator must be eliminated.
Children or untrained people
may be seriously injured by
this machine. Only install in an
access restricted location.
Figure 4.




 
Assembly
The base of this machine has mounting holes
that allow it to be fastened to a workbench or
other mounting surface to prevent it from moving
during operation and causing accidental injury or
damage.
The strongest mounting option is a "Through
Mount" (see example below) where holes are
drilled all the way through the workbench—and
hex bolts, washers, and hex nuts are used to
secure the machine in place.
Machine Base
Workbench
Bolt
Flat Washer
Flat Washer
Lock Washer
Hex Nut
Machine Base
Workbench
Lag Screw
Flat Washer
Another option is a "Direct Mount" (see example
below) where the machine is secured directly to
the workbench with lag screws and washers.
Mounting
Figure 5.
Figure 6.





Figure 7. 




 
Dust Collection
DO NOT operate the Model G0739 without an
adequate dust collection system. This sand-
er creates substantial amounts of wood dust
while operating. Failure to use a dust collec-
tion system can result in short and long-term
respiratory illness.
Recommended CFM at Dust Port: 100 CFM
Do not confuse this CFM recommendation with
the rating of the dust collector. To determine the
CFM at the dust port, you must consider these
variables: (1) CFM rating of the dust collector,
(2) hose type and length between the dust col-
lector and the machine, (3) number of branches
or wyes, and (4) amount of other open lines
throughout the system. Explaining how to cal-
culate these variables is beyond the scope of
this manual. Consult an expert or purchase a
good dust collection "how-to" book.
Power Connection
After you have completed all previous setup
instructions and circuit requirements, the machine
is ready to be connected to the power supply.
To avoid unexpected startups or property dam-
age, use the following steps whenever connecting
or disconnecting the machine.
Connecting Power
Figure 9. 
1. TurnthemachinepowerswitchOFF.
2. Insert the power cord plug into a matching
power supply receptacle. The machine is
nowconnectedtothepowersource.
Disconnecting Power
Figure 10. Disconnect power.
1. TurnthemachinepowerswitchOFF.
2. Graspthemoldedplugandpullitcompletely
outofthereceptacle.Donotpullbythecord
asthismaydamagethewiresinside.
Figure 8.
To connect a dust collection hose:
1. 
Figure 8

2.         




 
7.        

   does not   

   does  
    

     




Figure 11.
The switch can be disabled by removing the key,
as shown below. Disabling the switch in this man-
ner can prevent unauthorized operation of the
machine, which is important if it is not kept inside
an access-restricted building or in a location
where children may be present.
IMPORTANT: Disabling the switch only
restricts its function. It is not a substitute
for disconnecting machine from power when
adjusting or servicing.
Test Run
       
        

Note: You do not need to install a drum to perform
the test run.
       
 


        

     
TroubleshootingPage 22


To test run the machine:
1. 


2. 

3. 
4. 
ON
    
     


     
    


5. OFF
6.  
Figure 11

 
SECTION 4: OPERATIONS
Damage to your eyes and lungs could result
from using this machine without proper pro-
tective gear. Always wear safety glasses and
a respirator when operating this machine.
To reduce the risk of
serious injury when using
this machine, read and
understand this entire
manual before operating.
NOTICE
If you have never used this type of machine
or equipment before, WE STRONGLY REC-
OMMEND that you read books, review
industry trade magazines, or get formal
training before beginning any projects.
Regardless of the content in this section,
Grizzly Industrial will not be held liable for
accidents caused by lack of training.
Disabling Switch
Children or untrained people can be
seriously injured by this machine. This
risk increases with unsupervised operation.
To help prevent unsupervised operation,
always disable switch before leaving
machine unattended. Make sure to place
key in a well-hidden or secure location!
The switch can be disabled by removing the key,
as shown below. Disabling the switch in this man-
ner can prevent unauthorized operation of the
machine, which is important if it is not kept inside
an access-restricted building or in a location
where children may be present.
IMPORTANT: Disabling the switch only
restricts its function. It is not a substitute
for disconnecting machine from power when
adjusting or servicing.
Figure 12.

       
      



IMPORTANT: Disabling the switch only
restricts its function. It is not a substitute
for disconnecting the machine from power
when adjusting or servicing.

 
Sanding Drum/
Sleeve Installation


      
        


Sanding
Sleeves
Sanding
Drums
Table
Inserts
Spindle
Washers
  

   
   
   
   
To install or replace a sanding drum/sleeve:
1. 
2. 


3.

Figure 13
4.        
      

       


5.         


6.      
      

Figure 13
7.       



Figure 13.














Sanding
To sand a workpiece:
1.     ON    

2.        
     
       Figure
14


Figure 14.




 
SECTION 5: ACCESSORIES

Some aftermarket accessories can be
installed on this machine that could cause
it to function improperly, increasing the risk
of serious personal injury. To minimize this
risk, only install accessories recommended
for this machine by Grizzly.
NOTICE
Refer to the newest copy of the Grizzly
Catalog for other accessories available for
this machine.
PRO-STIK®Belt Cleaners
G1511—Large (11⁄2" x 11⁄2" x 81⁄2")
G1512—Small (2" x 2" x 12")
H1446 —13⁄8" x 41⁄4"
H1447—13⁄8" x 81⁄2"




Figure 15. 
Figure 16. 
Figure 17. 
H7828 Tool Table Plus - Complete
The Tool Table Plus was designed in response
to customer requests for a slightly wider and
taller table to accommodate small planers, wood
lathes, sanders and a variety of other bench-top
machines.
Replacement Sanding Sleeve 3 Packs
H5434—1⁄2" Dia. x 41⁄2", Hard A150
H5438—3⁄4" Dia. x 41⁄2", Hard A120
H5442—1" Dia. x 41⁄2", Hard A100
H5447—11⁄2" Dia. x 41⁄2", Hard A100
H5451—2" Dia. x 41⁄2", Hard A80
H5455—3" Dia. x 41⁄2", Hard A60


