Ground Control Glue and Fly Series User manual

RC
Features:
Designed to be very maneuverable and aerobatic.
Designed for vertical and horizontal center mass weight distribution.
Has a fully enclosed, full size fuselage.
The KF2 Airfoil provides lift like a traditional Airfoil.
Designed for build simplicity.
Made from 5mm Adams Readi-Board ;-)
Aircraft Specifications:
Description: Glue & Fly Series F-22 Nano
Build Version: V1
Designer: Ground Control RC
Design Date: 12/01/19
Wingspan: 254mm (10.0")
Length: 388mm (15.3")
CG (From Nose): 185mm (7.3")
Weight (Airframe): 19.0g (.67oz)
Weight (AUW): 40.5g (1.43oz)
Proficiency: Beginner, Intermediate, Advanced
Recommended Control Surface Deflection (From Neutral Position):
Elevon Mixing Deflection in Milimeters EXPO
Aileron: 17mm UP / 17mm Down 40
Elevator: 12mm UP / 12mm Down 40
Linkage Connections: Inner Hole on Servo Control Arm and Control Horn
www.groundcontrolrc.com
Ground Control RC TM - F-22 Nano V1
Glue and FlyTM Series
TM
TM

RC
Diagram Keys
www.groundcontrolrc.com
A-Fold (Above)
X
X
X
X
X
X
X
X
X
X
X
X
B-Fold (Beside)
A B
Suggestions & Notes
Do not install your fuselage motor mount plate until you have marked the location of the rear of the motor
with your prop and adapter installed to set the prop in the center of the prop slot.
The motor should be installed in the horizontal and vertical center of the fuselage.
The prop slot width can accommodate up to a 2.50 inch prop.
If different servos are used you may need to measure the servos and adjust the size of the openings
in the Landing Skids to match the dimensions of your servos.
The front of the fuselage access panel uses a Plastic Tab and the rear uses a Magnet.
A Motor Mount Template and a Vertical Stabilizer Angle Jig are included in the plans.
All Paper was removed from the Foam Board except the Bottom of the Wing Plate and Top of the Wing Plate
except where the KF2 Airfoil is installed.
The Fuselage on this Plane is not Score & Fold. The Fuselage will be Assembled from completely separate
Parts as the Paper has been removed to save weight.
The Pins for the Vertical Stabilizers and Landing Skids were fabricated from 2mm diameter Tooth Picks ;-)
I cut them to 8mm in length and insert 4mm into the Vertical Stabilizers and Landing Skids and 4mm into the
Wing Plate, glued of course.
The Pins for the Top Nose Panel are only 4mm in length as they are just for alignment for the Fuselage. So only
2mm inserted into the Top Nose Plate and 2mm inserted into the Fuselage Side Panels.
You can use whatever you want for Pins but they should be 2mm in diameter or less.
Fold Types
Score, Cut, and Remove
Foam from these areas.
Ground Control RC TM - F-22 Nano V1
Glue and FlyTM Series

RC
Recommended Electronics & Components:
*Electronics & Components Listed Below Are Actual Items Used In Flight Testing
*Thrust to weight ratio: (1S) 1.4:1
Motor: HappyModel EX1102 13500kv
Prop Shaft 1.5mm
w/Servo Connectors
1S LIPO = 57.0g total thrust
ESC: DYS 7A OPTO 1S-2S ESC
w/Servo Connectors
w/JST PH2.0 Battery Connector
Battery: URUAV 1S 3.8V 300mah 40C LIHV LIPO
Connector: JST PH2.0
Size: 62x12x8mm
Prop: King Kong/LDARC Racer 65mm T-Mount 1.5mm Hub 2-Blade (CCW)
Receiver: Minimum 3 Channel Low Voltage Micro Receiver
Servos: (2) 1.7g Low Voltage Micro Servo Mini JST Connector
Control Rods: (2) 89mm x .8mm (with Plastic Clevises)
FPV System: Optional - Turbowing 5.8G 48CH 25mw FPV CAM 700TVL 1/4 CMOS
Additional Weight: 3.5g
AUW 40.5 grams (without Optional FPV System)
Note: Make sure the Receiver and Servos you choose have matching connectors!
www.groundcontrolrc.com
TM
Ground Control RC - F-22 Nano V1
Glue and FlyTM Series

RC
Recommended Electronics & Components:
*Electronics & Components Listed Below Are Actual Items Used In Flight Testing
*Thrust to weight ratio: 1S LIPO 1.4:1
Happymodel EX1102 13500KV 2-3S Brushless Motor
https://www.banggood.com/Happymodel-EX1102-8500KV-9000KV-10000KV-13500KV-2-3S-Brushless-Motor-Original-for-Mobula7-HD-Sailfly-X-Drone-p-1447084.
html?p=WE081047791920140372
DYS XSD7A 7A Blheli_S 1-2s FPV Racing Brushless ESC
https://www.getfpv.com/dys-xsd7a-7a-blheli-s-1-2s-fpv-racing-brushless-esc.html
10 Pairs Kingkong / LDARC 1935 48.26mm 1.5mm Mounting Hole 3-Blade Propellers
https://www.banggood.com/10-Pairs-Kingkong-1935-48_26mm-1_5mm-Mounting-Hole-3-Blade-Bullnose-Propellers-for-90GT-Drone-p-1137419.html?p=WE081047791920140372
5Pcs URUAV 3.8V 250mAh 40C/80C 1S Lipo Battery PH2.0
https://www.banggood.com/5Pcs-URUAV-3_8V-250mAh-40C80C-1S-Lipo-Battery-PH2_0-for-Eachine-US65-UK65-URUAV-UR65-Mobula7-p-1364758.html?p=WE081047791920140372
2.4G 4CH Micro Low Voltage DSM2 DSMX Compatible Receiver Built-in Brushed ESC
https://www.banggood.com/2_4G-4CH-Micro-Low-Voltage-DSM2-DSMX-Compatible-Receiver-Built-in-Brushed-ESC-p-1072251.html?p=WE081047791920140372
1.7g Low Voltage Micro Digital Servo Mini JST Connector
https://www.banggood.com/1_7g-Low-Voltage-Micro-Digital-Servo-Mini-JST-Connector-for-RC-Model-p-1157620.html?p=WE081047791920140372
Turbowing 5.8G 48CH 25mw FPV Transmitter 700TVL 1/4 CMOS Wide Angle FPV Camera Support OSD NTSC/PAL Switchable
https://www.banggood.com/48CH-25mw-Transmitter-700TVL-OSD-Wide-Angle-FPV-Camera-NTSC-PAL-Switchable-p-1164450.html?p=WE081047791920140372
100pcs 6 X 1mm Neodymium Disc Super Strong Rare Earth N35 Magnets
https://www.banggood.com/100pcs-6-X-1mm-Neodymium-Disc-Super-Strong-Rare-Earth-N35-Magnets-p-962647.html?p=WE081047791920140372
www.groundcontrolrc.com
See Us On Youtube | Patreon | RCGroups | Facebook
https://www.youtube.com/c/GroundControlRC
https://www.patreon.com/groundcontrolrc
https://www.rcgroups.com/forums/member.php?u=754189
https://www.facebook.com/pg/Ground-Control-RC-1805295043132721/posts/
Ground Control RC TM - F-22 Nano V1
Glue and FlyTM Series

www.groundcontrolrc.com
TM
Ground Control RC - F-22 Nano V1
Glue and Fly TM Series
Part - Fuselage
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Fuselage Access Panel Bottom QTY : 1
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Fuselage Fixed Back Panel
Top & Bottom
QTY : 1 ea.
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Fuselage Access Panel Top QTY : 1
Cut Back Fuselage Panel from Fuselage Access Panel
B
Canopy & Fuselage (B-Fold)
Score Lines
>
Remove Paper Inside
>
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Fuselage QTY : 1
Cutout - Servo Wire Access
Cutout - Servo Wire Access
Wing Plate Alignment
Wing Plate Alignment
Cut and Separate
Cut and Separate
Nose Former Placement
Nose Former Placement
Back Plate Alignment
Top Nose Panel Pin Hole
Top Nose Panel Pin Hole
Ground Control RC - F-22 Nano V1
Copyright 2020 - For Personal Use Only
"Glue and Fly Series"
Test Scale = 50mm
Test Scale = 2 inch

www.groundcontrolrc.com
TM
Ground Control RC - F-22 Nano V1
Glue and Fly TM Series
Part - Fuselage
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Nose Reinforcement & Guide
QTY : 2
Top Bottom
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Fuselage Access Panel
Metal Tab for Magnet
QTY : 1
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Fuselage Access Panel
Plastic Tab
QTY : 1
Fuselage Back Panel
Fuselage Motor Mount
Back Plate
Happy Model
EX1102 13500kv
Motor Mount Plate
Score Lines
>
>
Remove Paper Inside
Canopy Placement
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Fuselage Top Nose Panel QTY : 1
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Canopy
QTY : 4
Ground Control RC - F-22 Nano V1
Copyright 2020 - For Personal Use Only
"Glue and Fly Series"
Test Scale = 50mm
Test Scale = 2 inch

www.groundcontrolrc.com
TM
Ground Control RC - F-22 Nano V1
Glue and Fly TM Series
CG CG
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Main Wing Plate
QTY : 1
Landing Skid Pin Holes
Landing Skid Pin Holes
Vertical Stabilizer
Pin Holes
Vertical Stabilizer
Pin Holes
Center Line
Prop Position
KF2 Airfoil Placement
KF2 Airfoil Placement
Part - Wing Plate
Ground Control RC - F-22 Nano V1
Copyright 2020 - For Personal Use Only
"Glue and Fly Series"
Test Scale = 50mm
Test Scale = 2 inch

www.groundcontrolrc.com
TM
Ground Control RC - F-22 Nano V1
Glue and Fly TM Series
Part - Elevons
Vertical Stabilizers
KF2 Airfoils
Landing Skids
Nacelle
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Nacelle QTY : 1
Control Horn
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Elevon QTY : 2
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Virt Stabilizer
QTY : 2
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : KF2 Airfoil
QTY : 2
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Angle Jig QTY : 1
Ground Control RC - F-22 Nano V1
Copyright 2020 - For Personal Use Only
"Glue and Fly Series"
Test Scale = 50mm
Test Scale = 2 inch

Ground Control RC - F-22 Nano V1
[ Aircraft Assembly Diagram - Fuselage ]
www.groundcontrolrc.com
Glue and Fly Series
RC

Ground Control RC - F-22 Nano V1
[ Aircraft Assembly Diagram - Wing Plate ]
www.groundcontrolrc.com
Glue and Fly Series
RC

Ground Control RC - F-22 Nano V1
[ Aircraft Assembly Diagram - Fuselage - Wing Plate ]
www.groundcontrolrc.com
Glue and Fly Series
RC

CG CG
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Main Wing Plate QTY : 1
Landing Skid Pin Holes
Landing Skid Pin Holes
Vertical Stabilizer Pin Holes
Vertical Stabilizer Pin Holes
Center Line
Prop Position
KF2 Airfoil Placement
KF2 Airfoil Placement
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Nacelle QTY : 1
Control Horn
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Elevon
QTY : 2
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Virt Stabilizer
QTY : 2
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : KF2 Airfoil
QTY : 2
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Fuselage Access Panel Bottom QTY : 1
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Fuselage Fixed Back Panel Top & Bottom
QTY : 1 ea.
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Fuselage Access Panel Top QTY : 1
Cut Back Fuselage Panel from Fuselage Access Panel
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Nose Reinforcement & Guide
QTY : 2
Top Bottom
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Fuselage Access Panel
Metal Tab for Magnet
QTY : 1
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Fuselage Access Panel
Plastic Tab
QTY : 1
Fuselage Back Panel Fuselage Motor Mount
Back Plate
Happy Model
EX1102 13500kv
Motor Mount Plate
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Vertical Stabilizer
Angle Jig
QTY : 1
B
Canopy & Fuselage (B-Fold)
Score Lines
>
Remove Paper Inside
>
Ground Control RC Aircraft: F-22 Nano Version : 1 Part : Fuselage QTY : 1
Cutout - Servo Wire Access
Cutout - Servo Wire Access
Wing Plate Alignment
Wing Plate Alignment
Cut and Separate
Cut and Separate
Nose Former Placement
Nose Former Placement
Back Plate Alignment
Top Nose Panel Pin Hole
Top Nose Panel Pin Hole
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Canopy
QTY : 4
Score Lines
>
>
Remove Paper Inside
Canopy Placement
Ground Control RC
Aircraft: F-22 Nano
Version : 1
Part : Fuselage Top Nose Panel
QTY : 1
Ground Control RC - F-22 Nano V1
Copyright 2020 - For Personal Use Only
"Glue and Fly Series"
Test Scale = 50mm
Test Scale = 2 inch