Groz BLP-02 User manual

1
DESCRIPTION
• Designedfortransferringtransmissiondifferentials&
heavieroils
• Zincplatedpumpbodywithaluminumdiecasthead
&adjustingflange
• Powdercoatedsteeldrumcover
• Wearresistantbrasspistonringsfittedontozincdie
castpiston
• Completewith48”/4’fuelresistantsoftPVChose
withnozzleforefficientdischarge
INSTRUCTIONMANUAL S1860,RevA
Oil Lube Dispensers
BLP-02, BLP-03
CONSTITUENT PARTS
REF. NO. PART NO PART DESCRIPTION QUANTITY
1KIT/BLP/1293 VinylHose(withAdaptor,Clamp,SteelSpout) 1
2 Notavailableasspare Pumptubeassembly 1
3 HND/BLP/02 LeverHandle 1
4 Notavailableasspare DrumCover 1
1
DeliverySpout
Adaptor
Clamp
Hose
2
3
DrumCover(BLP-03)
DrumCover(BLP-02)
4

2
ASSEMBLY & OPERATION
1. Placethedrumcoverassemblyoverthecontainer.Handtightenthethreethumbscrewsevenlyontothedrumcoverassemblytofixthe
drumcoverfirmlyontothecontainer.
2. Pulltheplungerrodofpistonsubassemblyup.Attachtheleverhandletothepistonrodusingthepivotpinandretainerclip.
3. Pushthepumptubeassemblydownthroughthediecastflangeofthedrumcoveruntilthepumptuberestsontothebaseofthecon-
tainer.Ensurethatthetubeassemblytouchesthebaseofthecontainer.
4. Tightenthemachinescrewandthehexnutintheflangeassemblytoholdthepumpassemblyfirmlyinplace.Donotovertightenthe
screwandnut.
5. Screwtheadapterontothepumpoutlet.Donotovertighten.Useathreadsealanttopreventleakage.
6. Screwthehoseassemblyontotheoutletendoftheadapter.
7. Nowthepumpisready.Startthepumpbymovingtheleverhandle.Primingisaprocessofgettingthepumpstartedbyoperatingthe
pumpafewtimes.IfthereisanydifficultyinPriming,putsomeoilinthepumpoutletandkeepoperatingtheleverhandleuntilthe
dischargebegins.
8. Pierceopenaholeonthedrumcoverusingapinpunch.Whenthepumpisnotinuse,placethehoseassemblyintothishole.
PUMP CONSTRUCTION
DrumCover
Tapered (in BLP-02)
Flat (in BLP-03)
PivotPin&Retainer Clip
48”/4’PVCHose
PlungerRod
MachineScrew&HexNut
ThumbScrew
DeliverySpout
SuctionTube
NonReturnValve
Piston
Nut
OutletAdapter
Flange
ConnectingLever
LeverHandle
withRubberGrip

3
WETTED COMPONENTS
Steel,Aluminum,Zinc,Brass,NBR,PVC
RECOMMENDED USE
Transmissiondifferentials&heavierOils
DO NOT USE WITH
Chemicals,Acids,Waterbasedfluids&othercorrosive
mediaetc.
Thepumpisconstructedusingplatedsteelcomponents.Itshould
neverbeusedtotransferfluidsthatmaycausethepumptorust.
Keepworkareacleanandremoveanyexcessoilfromtools,
hands,andclothingafteruse.
BLP-02 BLP-03
Discharge Rate Upto60ml(2.14oz.)perstroke
Mechanism LeverAction
Hose Length 48”
Outlet Size 1/4”NPT
Container Size 25-50lbs/5Gal/20Litres 120lbs/16Gal/60Litres
Drum Cover Dia. 12”(310mm) 15”(381mm)
Pump Length 18”(450mm) 30”(760mm)
SPECIFICATIONS
Problem Possible Cause Corrective Action
Pumpfailstoprime Primingisneeded Pourafewdropsofthefluidbeingdispensed
intothepumpoutlet.
Startthepumpbymovingtheleverwith
severalquickstrokes
Pumpdoesnotdispensethefluid Blockageinthesuctionline Removethepumpfromthedrumandensure
thatsuctiontube&non-returnvalveisfreeof
anyblockage
TROUBLESHOOTING

4
Groz Engineering Tools (P) Ltd.
Groz Net Industries
VillageKherkiDaula,NationalHighway-8
Gurgaon-122001,Haryana,INDIA
TEL+91.124.282.7700/221.4050
FAX+91.124.2827986/221.4224
FAX(USA)+1.509.271.7848
FAX(UK)+44.870.121.1854
E-MAIL[email protected]
URLwww.groz-tools.com
TheGrozname,Grozlogoandthemarkare
trademarksofGrozEngineeringTools(P)Ltd.India