Groz LED/670 User manual

INSTRUCTION MANUAL
S2880, REV A
1
LED 670
30W COB Rechargeable
Worklight
Powerful 30W COB
floodlight with dual power
source produces super
bright light up to 2800
lumen with wide spread
illumination
This floodlight works with
two power source:
• 115/220V AC
• Rechargeable Li ion
Battery
Aluminum die cast housing
in premium power coated
finish with Rubberised
Edge Guard making it
Impact Resistant
Detachable 7.4V 4400
mAh rechargeable Li-ion
battery pack and can also
be used a power bank
Comes with detachable
magnet base to latch onto
any metallic surface
Can be mounted on tripod
for outdoor sites
CAT NR. ORD NR.
LED/670 55050
LED/670 T 55077
IK07
RoHs
Detachable
Magnetic Base
30W COB
floodlight
Knob to
secure
attachment in
place
Rubberised
Edge Guard
POWER
SOURCE
Rechargeable
Li-ion Battery
AC Supply
WORKING
MODES
Two Modes:
1) 100% Intensity
2) 50% intensity
One Mode:
100% Intensity
LUMEN 1) 100% Intensity: 2800 Lm
2) 50% Intensity: 1400 Lm
100% Intensity: 2800 Lm
RUN TIME 1) 100% Intensity: 2 hrs
2) 50% Intensity: 4 hrs
100% Intensity: 2 hrs
SPECIFICATIONS
CHARGING
TIME
2.5H IP-54
WATER & DUST
PROOF RATING
115/220V AC
5V USB CABLE
POWER SOURCE

www.groz-tools.com
2
SAFETY INFORMATION
• Check for damaged parts and any other
conditions that may aect the operation
of this product. Replace damaged parts
immediately.
• Do not use the lamp in the immediate vicinity
of inflammable materials or gases.
• Only use the accessories included with the
product .
• Keep the lamp out of reach of unauthorised
persons, especially children.
• Do not point the light directly in your own or
any other person’s or animal’s eyes.
PACKAGING CONTENT
NOMENCLATURE
OPERATING INSTRUCTIONS (REFER
“NOMENCLATURE”)
Charging
1. Fully charge the battery before the first use
on battery source.
2. Turn o the light and connect to the supplied
charger cable.
3. When the battery is fully charged, all the
indicator LEDs will constantly turn GREEN .
4. Full charging takes about 2.5 hours.
OPERATION
Mount the magnetic base on the bracket as
shown below to mount the light on a metal
surface.
USE WITH BATTERY POWER
• To switch ON the light press the button
labeled ON/OFF at the back of the unit.
• To change the intensity of light press the
button labeled 50%/100%.
• Power Bank- Insert a USB cable in the USB
slot and the device connected with the
battery will start charging
DESCRIPTION QUANTITY
Light 1
Magnetic base 1
USB cable 1
ALight
BAdjusting Knob
CBracket
DMagnetic
EHandle
FButtons
GBattery Pack
HSocket
IAdaptor
A
E
F
G
B
C
D
H
I
Charging
input port
ON/OFF
USB output port
Intensity control
Battery Level Indicator
Side View
Back View

www.groz-tools.com 3
USE WITH AC POWER
1. Remove the battery from the light by
opening both the locks on the top and
bottom of the battery.
2. Assemble the adaptor and insert the cable
inside socket of the light.
3. Switch ON the power to switch on the light.
Note: There is no intensity setting for use in AC
power source
MAINTENANCE
• Before cleaning the LED worklight,
disconnect the USB cable(if being charged)
and allow the worklight to cool down
suciently.
• Clean with a dry or slightly moist, clean, lint-
free cloth and a mild detergent if required.
• Do not use cleaners that contain abrasives
or solvents.
• Check the LED worklight for damage before
each use. If the lens is damaged it must be
replaced immediately.
• Clean any dirt from the housing or the
lens immediately, since it could cause
overheating.
DISPOSAL
The components or the used products must
be given to companies that specialize in the
disposal and recycling of industrial waste.

Groz Engineering Tools (P) Ltd.
Groz Net Industries
Village Kherki Daula, National Highway-8,
Gurugram-122001, Haryana, INDIA
Tel [phone]
Fax [phone]
E-Mail [e-mail]
Url www.groz-tools.com
The GROZ name, GROZ logo and the mark are
trademarks of Groz Engineering Tools (P) Ltd., India