Grundig MT 6740 User manual

4 IN 1 MULTI
HAIR TRIMMER
MT 6740

2
_________________________________________________________
A
B
C
D
E
F
G
H
I
K
J

3
_________________________________________________________
DEUTSCH 4- 17
ENGLISH 18 - 29
FRANÇAIS 30 - 41
PORTUGUÊS 42 - 53
ESPAÑOL 54 - 65
POLSKI 66 - 77
ČESKY 78 - 89
TÜRKÇE 90 - 101
ΕΛΛΗΝΙΚA 102 - 113

18
SAFETY_______________________________________________
ENGLISH
Please note the following instructions
when using the appliance:
7The appliance is designed for
domestic use only.
7Observe these instructions in
order to prevent damage to the
appliance or danger arising
from improper use. Keep them
in a safe place.
7Never use the appliance in the
bath, shower or over a wash
basin filled with water; nor
should it be operated with wet
hands.
7Do not immerse the appliance in
water or let it come into contact
with water, even during
cleaning.
7Do not drop the appliance.
7Always disconnect the power
supply unit if the appliance is
not being charged or used.
7If not already present, for addi-
tional protection it is recommend
to install a residual-current-oper-
ated protective device (RCD)
with a rated residual operating
current not exceeding 30 mA in
the electrical circuit of your bath-
room. Ask your electrician for
advice.
7Never use the appliance if it is
visibly damaged.
7Keep the appliance away from
children.
7Do not open the appliance
under any circumstances. No
warranty claims are accepted
for damage caused by incorrect
handling.

ENGLISH 19
OVERVIEW__________________________________________
See the illustrations on page 2.
Controls
Professional cutting head
made from industrial ceramic
(width 38 mm).
Side catches for removing
attachments.
On/off switch.
Charging display (LED). Lights
up red when charging and
green when it is fully charged.
Socket for plugging into the
charging unit or connecting the
power supply unit.
Charging unit.
Accessories
Beard trimming attachment
(width 30 mm).
G
F
E
D
C
B
A
Extendable plug-in comb
system suitable for both cutting
widths, with precise trimming
grade display for hair lengths
of 2, 4, 6, 8, 10, 12, 14 and
16 mm.
Thinning comb for 2 mm
cutting length.
Shaving attachment with single
blade foil for a smooth shave.
Power supply unit.
Other accessories
1 x two combs.
1 x cleaning brush.
1 x oil for cutting head.
K
J
I
H

20
POWER SUPPLY ___________________________________
ENGLISH
Rechargeable battery
operation
When operating the appliance with
the built-in nickel metal hydride
battery, only use the power unit
supplied for charging.
Check if the mains voltage on the
type plate of the power supply unit
supplied corresponds to your local
mains supply.
1Plug the power cord into the
appliance socket and the
power supply unit into the wall
socket.
Notes
7Charge up the batteries comp-
letely before you use them for the
first time or if you have not used
them for a long time (approx. 12
hours’ timer-controlled charging).
– The charging display lights
up red when charging and
changes to green when it is
fully charged.
D
E
7Charging time is approx. 12
hours when the appliance is
switched off. If you switch on the
appliance while it is charging,
charging will stop.
– The charging display disap-
pears.
7The ambient temperature should
be between 5 °C and 40 °C.
7When fully charged, the appliance
works for around 60 minutes.
It is not advisable to charge the
batteries after every use, especially
if you do not use the appliance for
the full 60 minutes. Only charge
the batteries when they are
completely discharged. This
increases their service life. Do not
charge it every day.
D

ENGLISH 21
POWER SUPPLY ___________________________________
Using the charging unit
1Put the socket of the
appliance into the charging unit.
2Plug the power cord into the
socket on the charging unit.
3Plug the power supply unit into
the wall socket.
E
Mains operation
(with the power supply
unit)
Check if the mains voltage on the
type plate of the power supply unit
supplied corresponds to your local
mains supply.
The only way to disconnect the
device from the mains is to unplug
the power supply unit.
1Plug the power supply unit into
the socket on the appliance.
2Plug the power supply unit into
the wall socket.
Caution
7When in the bathroom or beside
a water connection, you must
only use the appliance in battery
mode; never run it from the
mains.
E

22
OPERATION ________________________________________
ENGLISH
Special features
This appliance has four separate
functions:
– Function 1: precise hair trimming
at a width of 38 mm.
– Function 2: precise beard
trimming at a width of 30 mm.
– Function 3: hair or beard
trimming with various cutting
lengths (2, 4, 6, 8, 10, 12, 14,
16 mm) at widths of 38 mm or
30 mm.
– Function 4: close shaving.
Switching on and off
1Press the button to switch on
the appliance.
2Press the button to switch off
the appliance.
C
C
Function 1
Trimming hair ...
... using the ceramic cutting head
(width 38 mm).
1If necessary, remove the attach-
ment by pressing in both side
catches and lifting off.
2Insert ceramic cutting head
carefully at the top and press
down until it clicks into place.
3Place a towel around the neck
and shoulder of the person
whose hair you are trimming.
A
B
A

ENGLISH 23
OPERATION ________________________________________
4Make sure the person is seated
so that their head is roughly at
your eye level. Before trimming,
comb the hair so that it falls
naturally and you can see the
direction in which it grows.
Function 2
Beard trimming ...
... using the beard trimming attach-
ment (width 30 mm).
1If necessary, remove the attach-
ment by pressing in both side
catches and lifting off.
2Insert beard trimming
attachment carefully at the
top and press down until it clicks
into place.
3Loosen the beard hair by comb-
ing the beard in the direction the
hair grows.
G
B
G

24
OPERATION ________________________________________
ENGLISH
3Push the extendable attachment
carefully and firmly onto the
rounded rear half of the cutting
head from above and let it click
into place.
4Adjust the cutting length (2, 4,
6, 8 or 10 mm) by pressing on
the lock next to the cutting
length display and then move
the comb to the setting you
want.
5After use, remove extendable
attachment by pressing the
locking tab at the back.
H
H
Function 3
Trimming hair or beards
at certain cutting
lengths ...
... using the extendable attachment
.
1If necessary, remove the attach-
ment by pressing in both side
catches and lifting off.
2Insert attachment (width
38 mm) or (width 30 mm)
carefully at the top and press
down until it clicks into place.
G
A
B
H

ENGLISH 25
OPERATION ________________________________________
Note
7You can remove the single blade
foil of the shaving attachment. To
do this, press both side catches
on the shaving attachment. Clean
the blade head with the cleaning
brush supplied.
Function 4
Close shaving ...
... using the shaving attachment .
1If necessary, remove the attach-
ment by pressing in both side
catches and lifting off.
2Insert shaving attachment
carefully at the top and press
down until it clicks into place.
Note
7Do not apply a lot of pressure
when shaving, as this could
damage the single blade foil.
J
B
J

26
OPERATION ________________________________________
ENGLISH
Function 5
Thinning out hair ...
... using the thinning comb
(thinning at a length of 2 mm).
1If necessary, remove the attach-
ment by pressing in both side
catches and lifting off.
2Insert attachment (width
38 mm) or (width 30 mm)
carefully at the top and press
down until it clicks into place.
G
A
B
I
3Push the thinning comb care-
fully and firmly onto the rounded
rear half of the cutting head
from above and let it click into
place.
4After use, remove thinning comb
by pressing the locking tab
at the back.
I
I

ENGLISH 27
CLEANING AND CARE___________________________
Cleaning and care
1Switch off the appliance and
unplug it from the mains.
2Remove the attachment and
clean the blade head with the
brush supplied.
Caution
7If cleaning with the brush is not
sufficient, you can also rinse the
attachment under running water.
However, only do this once the
attachment has been removed.
7The cutting head on the attachment
does not normally need to be
oiled. If you clean the attachment
under running water regularly but
you also want to maintain the
original condition of the cutting
head for as long as possible, it is
worth oiling it at regular intervals
with the oil provided.
3Use a soft, dry cloth or the brush
supplied to clean the appliance
housing and the charging unit.
Caution
7Never put the appliance, charging
unit or power supply unit in water
or any other liquid.
4Before using the appliance
again, dry all the attachments
properly using a soft towel.
5Do not use any cleaning agents.
Note
7Remove any clippings after each
use.

28 ENGLISH
CLEANING AND CARE___________________________
Storage
If you do not want to use the appli-
ance for a long period of time,
please store it carefully.
1Make sure it is unplugged, has
completely cooled down and all
the accessories are completely
dry.
2Store the parts in the original
box in a cool, dry place.
3Make sure the appliance is kept
out of reach of children.
Environmental note
This product has been made from
high-quality parts and materials
which can be re-used and recycled.
Therefore, do not throw the product
away with normal household waste
at the end of its service life. Take it
to a collection point for recycling
electrical and electronic devices.
This is indicated by this symbol on
the product, in the operating
manual and on the packaging.
Please find out about collection
points operated by your local
authority.
Help protect the environment by
recycling used products.

ENGLISH 29
INFORMATION ____________________________________
Technical data
This product fulfils the
European directives
2004/108/EC and
2006/95/EC.
Power supply
Batteries: Nickel metal hydride
Power supply unit
Ni-MH
Technical and design modifications reserved.

Grundig Multimedia B.V.
Atrium, Strawinskylaan 3105 •NL-1077 ZX Amsterdam •http://www.grundig.com
72011 903 8000