Grundig MT 6540 User manual

ǵ
FOUR IN ONE
BEARD TRIMMER
MT 6540

2
_________________________________________________________

3
_________________________________________________________
B
C
D
A
H
G
E
F
K
J
I
L
M

4
_________________________________________________________

5
_________________________________________________________
DEUTSCH 6 - 15
ENGLISH 16 - 25
POLSKI 26 - 35

16
SAFETY_______________________________________________
ENGLISH
Please note the following information
when using the appliance:
7The appliance is designed for
domestic use only.
7To prevent damage and danger
from improper use, please
observe the operating
instructions and keep them in a
safe place.
7Never use the appliance in the
bath, shower or over a
washbasin filled with water;
nor should it be operated with
wet hands.
7Do not immerse the appliance in
water or let it come into contact
with water, even during
cleaning.
7Do not drop the appliance.
7Pull out the mains adapter
after use.
7If the appliance is used in the
bathroom, it is essential that the
mains adapter is pulled out
after use, as water close to the
appliance can still constitute a
danger, even if it is switched off.
7Never use the appliance if it is
visibly damaged.
7Keep the appliance away from
children.
7Do not open the appliance
under any circumstances. No
warranty claims are accepted
for damage resulting from
improper handling.
M

ENGLISH 17
OVERVIEW__________________________________________
Fold out page 2 so that you have
the illustrations in front of you.
Controls
On/off switch.
Wide cutting head side,
22 mm.
Narrow cutting head side,
11 mm.
Collector tray for beard
trimmings (extendable).
3 x vacuum ventilation grilles.
LED charge indicator.
Charging stand.
Socket for connecting to the
charging unit or mains
adapter.
H
G
F
E
D
C
B
A
Accessories
Telescopic plug-in comb.
Grade adjuster.
Precision shaver.
Nostril hair trimmer.
Mains adapter.
M
L
K
J
I

18 ENGLISH
POWER SUPPLY ___________________________________
Operation with recharge-
able batteries
When using the built-in
rechargeable nickel metal hydride
batteries, use the mains adapter
supplied as a charger.
1Plug the mains adapter into the
socket, and plug the mains
adapter into the mains socket.
Notes
7Completely charge up the
batteries (16 hours) before you
first use them or if you have not
used them for a long time.
7During regular use, the charging
time with the appliance switched
off is around 8 hours. If you
switch on the appliance while it
is charging, charging will stop.
7The ambient temperature should
be between 5 °C and 40 °C.
H
M
7When fully charged, the
appliance works for around
45 minutes. It is not advisable to
charge the batteries after every
use, especially if you do not use
the appliance for the full
45 minutes. Only charge the
batteries when they are
completely discharged. This
increases their life. Do not
charge them every day.
Using the charging unit
1Plug the socket of the
appliance into the plug in the
charging unit.
2Plug the mains adapter cable
into the socket on the back of the
charging unit.
3Insert the mains adapter plug
in the socket.
Environmental note
7This appliance contains nickel
metal hydride batteries. Do not
dispose of it with your house-
hold waste at the end of its
service life. Open the housing.
Remove the batteries and take
them to a battery collection box
in a shop or public collection
point.
M
G
H

ENGLISH 19
POWER SUPPLY ___________________________________
Mains operation
(with mains adapter)
Check that the voltage on the mains
adapter type plate corresponds
to the rated voltage of your local
mains supply. The only way to
disconnect the device from the
mains supply is to unplug the
adapter.
1Insert the mains adapter plug
into the socket.
2Insert the mains adapter plug in
the socket.
– The built-in batteries are
switched off.
Note
7Only use the appliance in
battery mode when in the bath-
room or beside a water connec-
tion; never run it from the mains.
H
M
Environmental note
This product has been made from
high-quality parts and materials
which can be re-used and recycled.
Therefore, do not throw the product
away with normal household waste
at the end of its life. Take it to a col-
lection point for recycling electrical
and electronic devices. This is indi-
cated by this symbol on the product,
in the operating manual and on the
packaging.
Please find out about collection
points operated by your local
authority.
Help protect the environment by
recycling used products.

20 ENGLISH
OPERATION ________________________________________
Function 1
Beard trimming ...
... using the wide side of the cutting
head and the telescopic plug-in
comb .
1Make sure the appliance is
switched off.
2Carefully plug the comb onto
the cutting head until it catches.
Make sure it is the right way
round. You must be able to see
the numbers on the comb on the
back of the appliance.
Please note that the telescopic
comb can only be used with
the wide side of the cutting
head .
B
I
I
B
3Set the required beard trimming
length using the grade adjuster
on the telescopic comb.
The numbers 2, 4, 6, 8 and 10
are the length in millimetres.
4Then switch on the appliance
using the switch and start
trimming your beard.
Move the appliance in the direc-
tion your beard grows and
make sure the comb is always in
contact with your skin.
To not make excessively quick
movements.
A
J

ENGLISH 21
OPERATION ________________________________________
Function 2
Beard trimming ...
... using the narrow side of the
cutting head without the
telescopic plug-in comb.
Note that you cannot use the
telescopic plug-in comb with this
method.
The narrow side of the cutting head
is used for precise trimming of small
areas.
1Make sure the appliance is
switched off.
2Take off the comb :
Release the comb by gently
pressing with two fingers on the
release buttons on the side, and
lift it off.
3Taking off the cutting head or
accessories:
I
I
I
C
Grip the cutting head or the
accessory from the side and turn
it to the left until it is released.
4Putting on the cutting head or
accessory:
Turn the cutting head or accesso-
ry by 180° to the new cutting
position. Push the cutting head
or the accessory into the housing
and lock it by slightly moving it
to the right and then gently
pressing it down.
Note
7Danger of injury! When adjust-
ing the cutting head, make sure
you do not accidentally switch
on the appliance with the switch
.
A
12

22
OPERATION ________________________________________
ENGLISH
Function 3
Beard trimming ...
... with the shaver .
1The shaver is for complete
beard removal on selected,
small areas.
Note that you must first trim long
beard hair with one of the two
blades or .
2Make sure the appliance is
switched off.
3Take off the head you were
previously using as described
under function 2.
4Put on the shaver as
described under function 2.
5Then switch on the appliance
using the switch and start
shaving.
A
K
CB
K
K
Function 4
Nostril hair removal ...
... using the nostril hair trimmer .
1Make sure the appliance is
switched off.
2Take off the head you were pre-
viously using as described under
function 2.
3Put on the nostril hair trimmer
as described under
function 2.
4Turn on the appliance using the
switch .
5Carefully bring the nostril hair
trimmer up to your nostrils
and trim off any protruding
hairs.
Note
7Danger of injury! Never insert
the nostril hair trimmer into your
nostrils.
L
A
L
L

ENGLISH 23
OPERATION ________________________________________
General information
Vacuum system
7The appliance is equipped with
a state-of-the art vacuum system.
As soon as you switch it on,
the vacuum suction system is
activated and the trimmed hair
is hygienically caught in the
collector .
7Empty the collector every
time you trim your beard, by
pulling it out forwards, or as
often as necessary during a trim.
7Always put it back in after
emptying it.
7Make sure the three vacuum
ventilation grilles are not
covered while you use the
appliance.
E
D
D
Useful tips
7Hold the appliance with a
relaxed and comfortable grip.
7Always cut against the natural
direction of the hair.
7As you cut, take a break at
regular intervals. You can
always make a correction, but
not once the hair has been cut.
7Only cut a small amount the first
time you use the trimmer. This is
the only way to get used to the
adjustable cutting lengths.
7Comb your beard repeatedly
(using the comb supplied). Look
for hair which is too long.
7To ensure good results, your
beard should be dry.

24 ENGLISH
CLEANING AND CARE___________________________
Cleaning and care
1Switch off the appliance and
unplug it if you are running it
from the mains.
2Remove the comb attachment
if fitted, and clean the cutting
head and other attachments with
the brush supplied.
3Only clean the housing and the
comb with a damp, soft cloth.
Note
7Never immerse the appliance,
lead or mains adapter in water
or other liquids.
4Before using the appliance
again, dry all parts completely
using a towel.
5Do not use cleaning agents.
6Put the comb back on again.
Notes
7Remove any clippings after each
use.
I
Note
7Normally you do not need to oil
the cutting head, because it is
made of two different materials
(ceramic and steel). If you want
to maintain the original condition
of the cutting head for as long as
possible, it is worth oiling it at
regular intervals (with the oil
provided).
Storage
If you do not want to use the appli-
ance for a long period of time,
please store it carefully.
1Ensure that it is unplugged and
is completely dry.
2Store the parts in the original
packaging in a cool, dry place.
3Make sure the appliance is kept
out of reach of children.

ENGLISH 25
INFORMATION ____________________________________
Guarantee
The guarantee does not cover the
cutting head or defects which do
not significantly impair the value
or function of the appliance. The
guarantee is invalidated if the
appliance is damaged, opened or
improperly used.
Technical data
This product fulfils the
European directives
89/336/EEC and
73/23/EEC.
Power supply
Battery: Nickel metal hydride
Mains adapter
Ni-MH
Technical and design modifications reserved.

Grundig Multimedia B.V.
Atrium, Strawinskylaan 3105 • NL-1077 ZX Amsterdam • http://www.grundig.com
72011 900 6000