Grundig GDK 5792 XB User manual

COOKER HOOD
GDK 5792 XB
EN

Please read this user manual first!
Dear Customer,
Thank you for purchasing this Grundig product. We hope that you get the best results form your
product which has been manufactured with high quality and starte-of-the-art technology.
Therefore, please read this entire user manual and all other accompanying documents carefully
before using the product and keep it as a reference for future use. If you handover the product to
someone else, give the user manual as well. Follow all warnings and information in the
user manual.
Remember that this user manual is also applicable for several othet models. Differences between
models will be identified in the manual.
Please visit the “Support” section on the Grundig website
www.grundig.co.uk.to register your 5 year warranty.
Grundig Helpline
0845 603 1234
0345 603 1234

4
TABLE OF CONTENTS _____________________
1 Safety and set-up 6-7
2 At a glance 8
Control, parts and accessories . . . . . . 8
3 Operation 9-12
Connection of motor unit/hood . . . . . . 9
Wall drilling and bracket fixing . . . . . 10
Mounting the hood body. . . . . . . . . . 10
Connections ducted version
air exhaust system . . . . . . . . . . . . . . . 11
Recirculation version air outlet . . . . . . 11
Electrical connection . . . . . . . . . . . . . 11
Fitting the chimney . . . . . . . . . . . . . . . 12
Upper chimney. . . . . . . . . . . . . . . . . . 12
Grease filters . . . . . . . . . . . . . . . . . . . 14
Cleaning metal self-supporting
grease filters. . . . . . . . . . . . . . . . . . . . 14
Activated charcoal filter
(Recirculation version) . . . . . . . . . . . . 14
Replacing the activated
charcoal filter . . . . . . . . . . . . . . . . . . . 14
Light unit . . . . . . . . . . . . . . . . . . . . . . . 14
4 Information 15
Technical data . . . . . . . . . . . . . . . . . . 15
Environmental note. . . . . . . . . . . . . . . 15
5 Guarantee 16
6 Service 17

5
________________________________________________________

6
SAFETY AND SET-UP______________________
The Instructions for Use apply
to several versions of this ap-
pliance. Accordingly,you may
find descriptions of individual
features that do not apply to
your specific appliance.
Installation
7 The manufacturer will not be
held liable for any damages
resulting from incorrect or im-
proper installation.
7 The minimum safety distance
between the cooker top and
the extractor hood is 650 mm
(some models can be installed
at a lower height, please refer
to the paragraphs on working
dimensions and installation).
7 Check that the mains voltage
corresponds to that indicated
on the rating plate fixed to the
inside of the hood.
7 For Class I appliances, check
that the domestic power sup-
ply guarantees adequate
earthing. Connect the extrac-
tor to the exhaust flue through
a pipe of minimum diameter
120 mm. The route of the flue
must be as short as possible.
7 Do not connect the extractor
hood to exhaust ducts carry-
ing combustion fumes (boilers,
fireplaces, etc.).
7 If the extractor is used in con-
junction with non-electrical
appliances (e.g. gas burning
appliances), a sufficient de-
gree of aeration must be guar-
anteed in the room in order
to prevent the backflow of
exhaust gas. The kitchen must
have an opening communicat-
ing directly with the open air
in order to guarantee the entry
of clean air.
Use
7 The extractor hood has been
designed exclusively for do-
mestic use to eliminate kitchen
smells.
7 Never use the hood for pur-
poses other than for which it
has been designed.

7
SAFETY AND SET-UP______________________
7 Never leave high naked
flames under the hood when
it is in operation.
7 Adjust the flame intensity to
direct it onto the bottom of the
pan only, making sure that it
does not engulf the sides.
7 Deep fat fryers must be contin-
uously monitored during use:
overheated oil can burst into
flames.
7 Do not flambè under the
range hood; risk of fire.
7 This appliance can be used
by children aged from 8 years
and above and persons with
reduced physical, sensory or
mental capabilities or lack of
experience and knowledge if
they have been given supervi-
sion or instruction concerning
use of the appliance in a safe
way and understand the haz-
ards involved. Children shall
not play with the appliance.
Cleaning and user mainte-
nance shall not be made by
children without supervision.
7 Children should be supervised
to ensure that they do not play
with the appliance.
Maintenance
7 Switch off the appliance from
the mains supply before car-
rying out any maintenance
work.
7 Clean and/or replace the Fil-
ters after the specified time pe-
riod (Fire hazard).
7 Clean the hood using a damp
cloth and a neutral liquid de-
tergent.

8
AT A GLANCE____________________________
Control, parts and accessories
See the figure on page 3.
Ref. Q.ty Product Components
1 1 Hood Canopy complete with:
Controls, Light, Filters
2 1 Telescopic chimney, made up of:
2.1 1 Upper chimney
2.2 1 Lower chimney
3 1 Motor unit
9 1 Reduction Flange ø 150-120 mm
14.1 2 Air Outlet Connection Extension
15 1 Air Outlet Connection
Ref. Q.ty Installation Components
7.2.1 2 Upper chimney fixing brackets
7.3 1 Air Outlet Connection Support
11 6 Plugs
12a 6 Screws 4.2 x 44.4
12c 6 Screws 2.9 x 9.5
12f 6 Screws 3.5 x 9.5
Q.ty Documentation
1 Instruction Manual
GDK 5792 XB
Type Wall Island
Depth 460 mm
Width 898 mm
Min Height 730-1060 mm
Supply voltage 220-240 Volt 50 Hz
Control 4 positions
Suction power 270-530-645-860 m3/h
Motor power 270 W
Lamp power 2x1/4x1W
Total power 272 W
Air outlet pipe
diameter 120-150 mm
Net weight 13,3 kg
Gross weight 17,5 kg
Color Inox

9
OPERATION________________________________
Connection Of Motor Unit/
Hood
7 Remove the Grease filters from the Hood Can-
opy 1.
7 Remove any Activated charcoal filters from the
Motor unit 3.
7 From inside the Hood canopy, screw the Motor
unit 3 to the Hood canopy 1 using 6 Screws
12f provided.
7 Warning: Cable raceway 19 must be
screwed into place using one of the Screws
12f to fix it in the position shown in the figure,
locking the Hood wiring in place.
7 Warning: Make sure that the Power Cable is
not connected, then, if there is one, remove the
safety cover over the Connectors in Motor Unit
3 Wiring Box.
7 Make the electrical connections between the
Motor Unit 3 and the Hood Canopy 1, con-
necting the Controls connector and the Light-
ing connector.
Warning: Make sure that the Connectors
are properly inserted into the housing.
Warning: There will be a specific Connector
according to the type of controls.
7 For the Recirculation Version, fit the Activated
Charcoal Odour Filter, if there is one.
7 Replace the metal grease filters.

10
OPERATION________________________________
Wall drilling and bracket
fixing
Draw the following on the Wall:
7 a Vertical line up to the ceiling or top surface,
at the centre of the area in which the Hood is
to be fitted;
7 a Horizontal line: 650 mm min. above the
Cooker Top.
7 Rest the Bracket 7.2.1 as indicated, 1-2 mm
from the ceiling or surface above the hood,
aligning its centre (grooves) with the vertical
reference line.
7 Mark the centres of the holes in the bracket.
7 Rest the Bracket 7.2.1 as indicated, X mm under
the first bracket (X = height of the Upper chim-
ney provided), aligning its centre (grooves)
with the vertical reference line.
7 Warning: The Bracket must be in a position that
allows a minimum distance of 50mm from the
upper part of the Motor unit, so if when meas-
ured the position of the Bracket is found to be
below the Motor unit, the bracket must be fitted
50 mm above this.
7 Mark the centres of the holes in the bracket.
7 As shown in the drawing, mark a reference
point 116 mm from the vertical reference line,
and 545 mm above the horizontal reference
line.
7 Repeat this operation on the other side.
7 Drill the points marked using a ø 8 mm drill bit.
7 Insert the plugs 11 into the holes.
7 Fix the brackets, using the screws 12a (4.2 x
44.4 ) provided.
7 Tighten the 2 screws 12a (4.2 x 44.4) pro-
vided in the hood canopy fixing bores, leav-
ing a gap of 5-6 mm between the wall and the
heads of the screws.
Mounting the hood body
7 Before attaching the hood body, tighten the
two screws Vr located on the hood body
mounting points.
7 Hook the hood body onto the screws 12a.
7 Fully tighten the support screws 12a.
7 Adjust the screws Vr to level the hood body.