Grundig GDKP 2460 B User manual

Hood
User Manual
01M-8897293600-4120-04
EN - ES - RO
GDKP 2460 B

2
ENGLISH 04 - 14
ESPAÑOL 15 - 29
ROMÂNĂ 30 - 45

Please read this guide first!
Dear Customer,
Thank you for choosing a GRUNDIG product. We would like you to achieve the optimal
efficiency from this high quality product which has been manufactured with state
of the art technology. Please make sure you read and understand this guide and
supplementary documentation fully before use and keep it as a reference. Include
this guide with the unit if you hand it over to someone else. Observe all warnings and
information herein and follow the instructions.
Keep in mind that this user guide may apply to several product models. The guide
clearly indicates any variations of different models.
Symbols and their meanings
These symbols are used throughout this guide:
CImportant information and recommen-
dations regarding the use of the appli-
ance.
ACAUTION: Warnings on personal injury
or property damage.
BElectric shock warning,
Risk of fire warning.
Complies with WEEE Regulations. No PCB Included.
This product has been manufactured at modern facilities respectful to the environment without harm-
ing nature.

4ENGLISH
General Safety
Important Safety Instructions Read Carefully
And Keep For Future Reference This section
contains safety instructions that will help pro-
tect from risk of fire, electric shock, exposure
to leak microwave energy, personal injury or
property damage. Failure to follow these in-
structions shall void any warranty.
■ Grundig products comply with the appli-
cable safety standards; therefore, in case
of any damage on the appliance or power
cable, it should be repaired or replaced by
the dealer, service center or a specialist
and authorized service alike to avoid any
danger. Faulty or unqualified repair work
may be dangerous and cause risk to the
user.
■ This appliance is intended to be used in
household and similar applications such
as:
– Staff kitchen areas in shops, offices and
other working environments;
– Farm houses
– By clients in hotels, and other residential
type environments;
– Bed and Breakfast type environments.
■ Operate the appliance for its intended pur-
pose only as described in this manual.
■ The manufacturer cannot be held liable for
damages resulting from improper installa-
tion or misuse of the product.
■ This appliance can be used by children
aged from 8 years and above and persons
with reduced physical, sensory or men-
tal capabilities or lack of experience and
knowledge if they have been given super-
vision or instruction concerning use of the
appliance in a safe way and understand the
hazards involved.
■ Children shall not be allowed play with the
appliance. Cleaning and user maintenance
shall not be made by children without su-
pervision.
■ The minimum distance between the sup-
porting surface for the cooking vessels on
the hob and the lowest part of your product
must be at least 65 cm.
■ If the instructions for installation for the gas
hob specify a greater distance, this has to
be taken into account.
■ Make sure that your mains power supply
complies with the information supplied on
the rating plate of the appliance.
■ Never use the appliance if the power cable
or the appliance itself is damaged.
■ Prevent damage to the power cable by not
squeezing, bending, or rubbing it on sharp
edges. Keep the power cable away from
hot surfaces and naked flame.
■ Use the appliance with a grounded outlet
only.
WARNING: Do not connect the appliance to
the mains until the installation is fully com-
plete.
IMPORTANT SAFETY AND ENVIRONMENTAL INSTRUCTIONS ______

5
ENGLISH
■ Place the appliance in a way so that the
plug is always accessible.
■ Do not touch the lamps if they have oper-
ated for a long time. They can burn your
hands since they will be hot.
■ Follow the regulations set out by compe-
tent authorities on discharge of the exhaust
air (this warning is not applicable for use
without Chimney ).
■ Operate your appliance after putting a pot,
pan etc. on the hob. Otherwise, high heat
may cause deformation in some parts of
your product.
■ Turn off the hob before taking the pot, pan
etc. from it.
■ Do not leave hot oil on the hob. Pans with
hot oil may cause self combustion.
■ Pay attention to your curtains and covers
since oil may catch fire while cooking food
such as fries.
■ Grease filter must be replaced at least
monthly. Carbon filter must be replaced at
least every 3 months.
■ Product shall be cleaned accordance with
user manual. If cleaning was not carried
out in accordance with user manual, there
may be fire risk.
■ Do not use non-fire-resistant filtering ma-
terials instead of the current filter.
■ Only use the original parts or parts recom-
mended by the manufacturer.
■ Do not operate the product without the fil-
ter and do not remove the filters while the
product is running.
■ In the event of be started any flame,
de-energize your product and cooking ap-
pliances.
■ In the event of be started any flame, cover
the flame and never use water to extin-
guish.
■ Unplug the appliance before each cleaning
and when the appliance is not in use.
■ The negative pressure in the environment
should not exceed 4 Pa (4 x 10 bar) while
the hood for electric hob and appliances
running on another type of energy but elec-
tricity operate simultaneously.
■ In the environment where the appliance is
being used, the exhaust of devices running
on fuel oil or gas, such as room heater
must be absolutely isolated or device must
be hermetical type.
■ When connecting the Chimney , use pipes
with a diameter of 120 or 150 mm. Pipe
connection must be as short as possible
and have as few elbows as possible.
Danger of choking! Keep all the packaging
materials away from children.
CAUTION: Accessible parts may become hot
when used with cooking appliances.
■ The product outlet must not be connected
to air channels that include other smoke.
■ The ventilation in the room may be insuf-
IMPORTANT SAFETY AND ENVIRONMENTAL INSTRUCTIONS ______

6ENGLISH
ficient when the hood for electric hob is
used simultaneously with the devices op-
erating on gas or other fuels (this may not
apply to appliances that only discharge the
air back into the room).
■ Objects placed on the product may fall. Do
not place any objects on the product.
■ Do not flambe under the your product.
WARNING: Before installing the Hood, re-
move the protective films.
■ Never leave high naked flames under the
hood when it is in operation
■ Deep fat fryers must be continuously mon-
itored during use: overheated oil can burst
into flames.
Compliance with the WEEE Directive and
Disposing of the Waste Product:
This product complies with EU WEEE Direc-
tive (2012/19/EU).This product bears a clas-
sification
symbol for waste electrical and electronic
equipment (WEEE).
This symbol indicates that this
product shall not be disposed with
other household wastes at the end
of its service life. Used device must
be returned to offical collection point for re-
cycling of electrical and electronic devices.
To find these collection systems please con-
tact to your local authorities or retailer where
the product was puchased. Each household
performs important role
in recovering and recycling of old appliance.
Appropriate disposal of used appliance helps
prevent potential negative consequences for
the environment and human health.
Compliance with RoHS Directive
The product you have purchased complies
with EU RoHS Directive (2011/65/EU). It does
not contain
harmful and prohibited materials specified in
the Directive.
Package Information
Packaging materials of the product
are manufactured from recyclable
materials in accordance with our
National Environment Regulations. Do not
dispose of the packaging materials together
with the domestic or other wastes.Take them
to the packaging material collection points
designated by the local authorities
.
IMPORTANT SAFETY AND ENVIRONMENTAL INSTRUCTIONS ______

7
ENGLISH
GENERAL APPEARANCE ___________________________
Overview
Technical Data
1. Inner Chimney
2. Outer Chimney
3. Control Panel
4. Aluminum Grease Filter
5. Lighting
(Figure 2)
(Figure 1).
GDKP 2460 B
Model GDKP 2460 B
Supply voltage 220-240V ~ 50 Hz
Lamp Power 2 x 3 W
Motor Power 210 W
Flow rate (m³/h) – 3. Level 627 m³/h
Insulation Class of Motor Class F
Insulation Class Class I
504
598
53
Mn643 Max 1023
590
20
380
261
250
80 25

8ENGLISH
OPERATION OF THE APPLIANCE ______________________
Controlling the Appliance
KEY FUNCTION
(A) : 1. Stage Button Operates the appliance on 1st speed. When you press this button again to turn off
the appliance, the screen speed stage turns off.
(B) : 2. Stage Button Operates the appliance on 2nd speed. When you press this button again to turn
off the appliance, the screen speed stage turns off.
(C) : 3rd Stage Button Operates the appliance on 3rd speed. When you press this button again to turn off
the appliance, the screen speed stage turns off.
(D) : Light On / Off You may illuminate the cooking area by pressing this button. Re-press the button
to turn off the lamp.
Energy Efficient Usage
■ When using your appliance, adjust the speed
settings according to vapour and odour intensity,
in order to save energy.
■ Use low speeds (1-2) under normal conditions,
and high speed (3) for intense odour and vapour.
■ * The lamps on the hood are placed for illuminat-
ing the cooking area.
Using them for environmental lighting shall cause
unnecessary energy expenditure and insufficient
lighting.
Operating the Hood
■ Your appliance contains a motor that has various
speeds.
■ For better performance, we recommend using
low speeds under normal conditions and high
speeds in cases of strong odours and intense
vapour.
■ You can start your appliance by pressing on the
desired speed setting button. (A, B, C)
■ You may illuminate the cooking area by pressing
the lamp (D).
Automatic Stop
Your appliance has Automatic Stop feature, ena-
bling it to ventilate for a bit more and remove the
unwanted odours and vapour inside the environ-
ment and turn off automatically after the cooking
is done. To enable Automatic Stop feature, press
the any speed stage button (A, B, C) on the control
panel for longer than 2 seconds; the 15-minute
timer function shall be activated. When the au-
tomatic stop feature is active, pressing the same
speed button shall disable the automatic stop func-
tion and the appliance's motor shall stop. This fea-
ture is disables when you switch between different
speed stages. If you want the appliance to stop au-
tomatically, you need to enable the automatic stop
feature again.
A B CD

9
ENGLISH
OPERATION OF THE APPLIANCE ______________________
Operation with Chimney Con-
nection
■ Vapour is extracted through
the flue duct, which is fas-
tened to the connection head
on the hood.
■ The diameter of the flue duct must be the
same as the connection ring. In horizontal
settings, the pipe has to have a slight up-
ward slope (around 10º) so that the air can
exit the room easily.
Operation without Chimney Con-
nection
■ Air is filtered through the
carbon filter and recirculated
in the room. Carbon filter is
used when it is impossible to
use a flue in the house.
■ In flueless use, remove the flaps inside the
flue adapter.
■ Remove the aluminum grease filter. To in-
stall the carbon filter, fit the filter to the tabs
by centring it on the plastic piece on both
sides of the fan body. tighten it by turning
right or left.
■ Replace aluminum grease filter.
Bulb
Bulb Power (W) 3
Holder / Socket GZ 10
Bulb Voltage (V) 220 - 240
Size (mm) 53 x 50
ILCOS Code DR/F3-220-240-
GZ10-50-53
Replacement of Lamp
(Figure 3)
Make the electrical connections of the appli-
ance.Your appliance uses 3W spot LED lamp.
For replacing the lamps, push downwards
on the holder from its behind, turn it coun-
ter-clockwise, and take it out downwards.
Apply the above operation in reverse to install
new lamps (Figure 3).

10 ENGLISH
CLEANING AND MAINTENANCE _______________________
C
Before cleaning and mainte-
nance, unplug the product or
turn off the switch.
Cleaning of Aluminum Grease
Filter
Aluminum grease filter is used to retain the
oil particles in the air. Aluminum grease filter
may change colour after repeated cleaning.
This is normal, and you do not have to replace
your filters.
(Figure 4)
■ Push the aluminum grease filter lock for-
ward.
■ Then pull it slightly down and pull it out
(Figure 4). Otherwise, you may bend the fil-
ter. Wash and rinse aluminum grease filter
with liquid detergent and replace aluminum
grease filter to their seats by carrying out
the steps specified above in reverse order.
These aluminum grease filter are used to
retain the oil particles in the air.
C
You may also wash the alumi-
num greasefilterinthe washing
machine.
A
CAUTION
Incaseofnormaluse,cleanyour
aluminum grease filter once in
a month.
Replacement of Carbon Filters
(Figure 5)
The appliance you have purchased is appro-
priate for use with carbon filters.
■ Remove the aluminum grease filter
(Figure 4).
■ Place the lower part of the carbon filter to the
motor cabinet (Figure 5).
■ Press on the tab of the carbon filter and
push it forward, and ensure that the tabs
of carbon filter are engaged and locked.
(Figure 5).
■ Attach the aluminum grease filter.
A
CAUTION
Carbon filter shall never be
washed.
A
CAUTION
Replace carbon filters once
every 3 months.
A
CAUTION
You can obtain the carbon filter
from the authorized services.

11
ENGLISH
Position of the Appliance
■ Distance between the cooker and the cooker
hood must be considered prior to assembly.
This distance should be 65 cm (Figure 6).
■ Distance must be measured from the sur-
face of grate for gas cookers,
■ from surface of glass for electric cookers.
INSTALLATION OF APPLIANCE _______________________
A
WARNING!
Before starting the installation,
read the safety information on
User Manual.
A
WARNING!
Failure to install with screws and
stabilizersinaccordance withthese
instructions may result in electric
shock.
For the installation of the hood, please contact
the nearest Authorized Service.
It is the customer's responsibility to prepare
the location and electrical installation of the
hood.
Hood
User Manual
01M-8897293600-2720-01
01M-8897303600-2720-01
EN - ES - RO
GDKP 2460 B - GDKP 5460
1. Product
2. Inner Chimney
3. Outer Chimney
4. Ø150/120 mm Plastic Flue Adapter
5. Chimney Connection Plate
6. User Manual
7. Assembly Pattern
8. 2x Hanging Plates
9. 2x Ø6mm Plastic Dowel
10. 3x Ø10mm Plastic Dowel
11. 3x 5.5x60 Wall Mount Screw
12. 2x M5x35 Hanging Plate Connection
Screw
13. 2x 3.9x22 Chimney Connection Plate
Screw
14. 2x 3.5x9.5 Chimney Connection Plate
Screw
15. Chimney Clamp
The information required to make the location
suitable for the installation of the hood is giv-
en below.
(Figure 6)
Installation Accessories

12 ENGLISH
INSTALLATION OF APPLIANCE _______________________
A
CAUTION
Beforedrilling,ensurethatthere
arenopower,gasorwater pipes
in the close proximity of the
drilling locations.
Draw a mid location line from the ceiling per-
pendicular to the lower edge of the hood ().
Fix the assembly scheme on the wall. For
points A and B, take the maximum dimen-
sions of the hood as reference, and drill points
A and B you have marked with a Ø6mm drill
bit, and tap Ø6mm plastic wall plugs. Install
the chimney connection plate to the wall with
2 pieces of 3.9x22 screws (Figure 8).
To install the hood body, drill points C,D,E
specified in the installation template with a
Ø10mm drill bit and tap Ø10mm plastic dow-
els to these points (Figure 8).
Install 2 pieces of 5.5x60 mounting screws to
points C and D with a clearance of 5 mm be-
tween the screw head and the wall (Figure 8).
(Figure 7)
(Figure 8)
(Figure 9)
Wall Mounting
• Wall must be flat, straight and have the
sufficient bearing capacity.
• Depth of drilling holes must comply with
the length of bolts.
• The bolts and dowels provided are suitable
for brick walls. For other construction
material (e.g. drywall, plate, porous
concrete), suitable fixing dowels and nuts
shall be used.
Install two pieces of hanging plates to the
body of the hood with M5x35 mounting
screws (Figure 8).

13
ENGLISH
INSTALLATION OF APPLIANCE _______________________
Connecting to Chimney
If you are going to use the Ø 120/150 mm
plastic Chimney adapter, connect one end of
the pipe to this adapter, if you are not going
to use it, to the direct output on the product.
Connect the other end of the pipe to your
Chimney . Check that these two connections
are tight enough so they will not come out
when the appliance runs on full power. Check
if the flaps inside the Chimney operate when
they are tightened
with clamps. Connect the Chimney connec-
tion duct outside the adapter (Figure 11/a).
If the connection duct is fitted inside the
adapter, suction of air shall not occur as the
Chimney flap that prevents the return of air
will remain closed (Figure 11 / b). The length
of the pipe connection as well as the number
of elbows must be as minimum as possible.
A : Chimney exit pipe
B : Non return flaps
C: Plastic flue
The valves are closed then the appliance is
not operating and prevent possible outside
odour and dust from entering inside.
Hold the cooker hood by its body and place it
on the mounting screws on the wall and tight-
en the screws (Figure 9).
Secure the cooker hood with a 5.5x60 screw
to the wall through the mounting hole on the
interior of the appliance (Figure 9).
Installation of the Hood to the
Chimney
Make the electrical connection of your hood
before starting the installation of the Chimney
. Slip the Chimney plates around the body.
Install the Chimney plate to the Chimney fas-
tening plate that is secured to the wall from its
upper outer edges (Figure 12).
(Figure 12)
1. Inner Chimney
2. 3.5x9.5 Screw
3. Chimney Connection Plate
(Figure 11)
Ok Not Ok
(a) (b)
(Figure 10)

14 ENGLISH
TROUBLESHOOTING ______________________________
Troubleshooting Root Cause Help
Appliance is not
working. Check your fuses. Fuse may be blown, inspect and restore it.
Appliance is not
working. Check the electrical connection. Mains voltage shall be be- tween 220 and 240 V.
Appliance is not
working. Check the electrical connection. Check if other appliance in your kitchen operate.
Illumination light
does not operate. Check the electrical connection. Mains voltage shall be be- tween 220 and 240 V.
Illumination light
does not operate. Inspect the lamp switch. Lamp switch shall be at "on" position.
Illumination light
does not operate. Inspect the lamps. The lamps of the appliance shall illuminate.
Air inlet of the appli-
ance is inadequate. Inspect the aluminium filter. Under normal operating con- ditions, aluminum grease fil-
ter shall be cleaned at least
once in a month.
Air inlet of the appli-
ance is inadequate. Check the air discharge chimney . The air discharge chimney shall be at “on” position.
Air inlet of the appli-
ance is inadequate. Inspect the carbon filter. The filters of the applianc- es with carbon filters shall
be replaced once in every 3
months under normal condi-
tions.

¡Por favor, lea esta guía primero!
Estimado cliente,
Gracias por elegir un producto GRUNDIG. Nos gustaría que sacara el máximo provecho
de este producto de alta calidad que ha sido fabricado con tecnología punta. Por
favor, asegúrese de leer y entender completamente esta guía y la documentación
complementaria antes de usarla y guárdela como referencia. Entregue esta guía junto
al aparato si se entrega o vende a otra persona. Observe todas las advertencias e
información aquí contenidas y siga las instrucciones.
Tenga en cuenta que esta guía del usuario se puede aplicar a varios modelos de
aparato. La guía indica claramente las posibles variaciones de los diferentes modelos.
Símbolos y sus significados
Estos símbolos se utilizan a lo largo de esta guía:
CInformación importante y recomenda-
ciones sobre el uso del aparato.
APRECAUCIÓN: Advertencias sobre lesio-
nes personales o daños a la propiedad.
BAdvertencia de descarga eléctrica,
Riesgo de fuego.
Cumple con la Directiva WEEE.
Este producto fue fabricado sin dañar la naturaleza en instalaciones modernas respetuosas con
el medio ambiente.
No incluye PCB.

16 ESPAÑOL
Seguridad general
Lea las instrucciones importantes de seguri-
dad y guárdelas para su futura consulta
Esta sección contiene instrucciones de se-
guridad que ayudarán a la protección contra
los riesgos de incendio, descargas eléctricas,
exposición a la energía de microondas, le-
siones personales o daño a la propiedad. El
incumplimiento de estas instrucciones anu-
lará cualquier tipo de garantía.
■ Los productos Grundig cumplen con todas
las normas de seguridad aplicables; por
ello, si el cable o el aparato presentan
daños, deberán ser reparados o sustituidos
por el distribuidor, un servicio técnico o una
persona cualificada y autorizada para evi-
tar cualquier peligro. Los trabajos de repa-
ración deficientes o realizados por personal
no cualificado puede ser peligrosos y en-
trañar riesgos para el usuario.
■ Este aparato está destinado al uso
doméstico y aplicaciones parecidas, como
por ejemplo:
– Cocinas para uso del personal de tien-
das, oficinas y otros entornos laborales;
– Casa rurales;
– Por clientes en hoteles o cualquier otro
tipo de entorno residencial;
– Entornos de tipo «Habitación y desayuno»
(Bed and Breakfast).
■ Utilice este aparato únicamente para su
uso previsto, tal como se describe en este
manual.
■ El fabricante no se hace responsable de
los daños provocados por una instalación
incorrecta o un uso inapropiado del pro-
ducto.
■ Este aparato puede ser utilizado por niños
mayores de 8 años y por personas con
capacidades físicas, sensoriales o men-
tales reducidas o con falta de experiencia
y conocimientos, siempre que estén bajo
supervisión o hayan recibido instrucciones
pertinentes sobre el uso del aparato de
manera segura y comprendan los peligros
que conlleva.
■ No deje que los niños jueguen con el
aparato. La limpieza y mantenimiento del
usuario no deben ser realizados por niños
sin supervisión.
■ La distancia mínima entre la superficie de
soporte de los recipientes para cocinar
en los fogones y la parte más baja de su
aparato debe ser de al menos 65 cm.
■ Si en las instrucciones de instalación de la
placa de gas se indica una distancia supe-
rior, deberá tenerse en cuenta este hecho.
■ Asegúrese de que la fuente de alimentac-
ión cumpla con la información que se ind-
ica en la placa de datos del aparato.
■ Nunca utilice el aparato si está dañado el
cable de alimentación o el mismo aparato.
■ Evite daños al cable procurando que no
sufra tirones, no se doble y no roce con
INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD Y MEDIO AMBIENTE _____

17
ESPAÑOL
bordes afilados para evitar dañarlo. Man-
tenga el cable de corriente alejado de su-
perficies calientes y llamas descubiertas.
■ Use el aparato únicamente con un enchufe
con toma a tierra.
ADVERTENCIA: No conecte el aparato a la
red eléctrica antes de que la instalación se
haya realizado por completo.
■ Coloque siempre el aparato de forma que
el enchufe quede a mano.
■ No toque las lámparas si han estado en
funcionamiento durante mucho tiempo.
Pueden ocasionar quemaduras en las
manos ya que estarán calientes.
■ Siga las normas establecidas por las au-
toridades competentes para la descarga
del aire de salida (esta advertencia no es
aplicable sin la conexión de la chimenea).
■ Encienda el aparato después de colocar
una olla, una sartén, etc, en los fogones.
De lo contrario, las altas temperaturas
pueden provocar deformaciones en algu-
nas partes del aparato.
■ Apague los fogones antes de retirar las
ollas, los sartenes, etc.
■ No deje aceite caliente en los fogones. Las
sartenes con aceite caliente pueden oca-
sionar autocombustión.
■ Preste atención a las cortinas y los estores,
ya que, al cocinar platos como patatas fri-
tas, el aceite puede originar un incendio.
■ El filtro antigrasa se debe reemplazar por lo
menos una vez al mes. El filtro de carbón
se debe reemplazar por lo menos cada 3
meses.
■ El producto se debe limpiar siguiendo las
instrucciones del manual de usuario. Si la
limpieza no se ha llevado a cabo siguiendo
el manual de usuario, puede haber riesgo
de incendio.
■ No use materiales filtrantes que no resistan
el fuego en vez del filtro actual.
■ Utilice únicamente accesorios originales o
bien los que recomiende el fabricante.
■ No use el aparato sin el filtro y no retire los
filtros mientras el aparato esté en funcio-
namiento.
■ En caso de fuego, desactive su producto y
los aparatos de cocina.
■ En caso de fuego, cubra la llama y nunca
utilice agua para apagarlo.
■ Desenchufe el aparato antes de cada limp-
ieza y cuando no esté en uso.
■ La presión negativa de la estancia no debe
superar los 4 Pa (4 x 10 bar) cuando la
campana para una placa eléctrica funcione
simultáneamente con dispositivos de otro
tipo de energía excepto la electricidad.
■ En la estancia en donde se encuentra el
aparato, el escape de equipos de combus-
tible o gas, como calefactores, deben ser
herméticos o estar absolutamente aisla-
dos.
■ Para la conexión de la chimenea, use tu-
INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD Y MEDIO AMBIENTE _____

18 ESPAÑOL
berías de 120 o 150 mm de diámetro. La
conexión de las tuberías debe ser lo más
corta posible y tener la menor cantidad de
codos de tubería.
¡Peligro de descarga eléctrica!Mantenga
todos los materiales de embalaje alejados de
los niños.
PRECAUCIÓN: Las partes accesibles pueden
alcanzar temperaturas elevadas al usarse
con cocinas.
■ El canal de salida del aparato no debe estar
conectado a canales de aire por los que
pasan humo.
■ La ventilación de la estancia puede ser in-
suficiente cuando la campana extractora
para placas eléctricas se utiliza al mismo
tiempo que los aparatos que funcionan con
gas u otros combustibles (esto puede no
ser aplicable a los aparatos que solamente
descargan el aire de nuevo en la estancia).
■ Los objetos colocados encima del producto
pueden caerse. No coloque ningún objeto
encima del aparato.
■ No flambear debajo del aparato.
ADVERTENCIA: Antes de instalar la cam-
pana, retire las películas protectoras.
■ No dejar llamas altas descubiertas debajo
de la campana extractora cuando está en
funcionamiento
■ Las freidoras se deberán vigilar continua-
mente durante su utilización: el aceite so-
brecalentado es inflamable.
De conformidad con la Directiva RAEE y
eliminación del producto al final de su
vida útil:
Este producto cumple con la Directiva RAEE
de la UE (2012/19/UE). Este producto lleva
un símbolo de clasificación de residuos de
aparatos eléctricos y electrónicos (RAEE).
Este símbolo indica que este pro-
ducto no debe eliminarse con otros
residuos domésticos al final de su
vida útil. El aparato usado debe ser
devuelto al punto de recogida oficial para el
reciclaje de aparatos eléctricos y electrónic-
os. Para encontrar estos sistemas de recogi-
da, por favor, póngase en contacto con las
autoridades locales o con el distribuidor don-
de se compró el producto. Cada hogar de-
sempeña un papel importante en la recuper-
ación y el reciclaje de los aparatos viejos.
La eliminación adecuada de los aparatos
usados ayuda a prevenir las posibles conse-
cuencias negativas para el medio ambiente y
la salud humana.
Conformidad con la Directiva RoHS
El producto que ha adquirido cumple con la
Directiva RoHS de la UE (2011/65/UE). No
contiene materiales peligrosos ni prohibidos
especificados en la Directiva.
Información sobre el embalaje
Los materiales de embalaje del
producto están fabricados con ma-
INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD Y MEDIO AMBIENTE _____

19
ESPAÑOL
INSTRUCCIONES IMPORTANTES SOBRE SEGURIDAD Y MEDIO AMBIENTE _____
teriales reciclables de acuerdo con nuestra
Normativa Medioambiental Nacional. No
deseche los materiales de embalaje junto
con los residuos domésticos o de otro tipo.
Llévelos a los puntos de recogida de material
de embalaje designados por las autoridades
locales
.

20 ESPAÑOL
APARIENCIA GENERAL ______________________________
Visión de conjunto
Datos técnicos
1. Conducto interno
2. Conducto exterior
3. Panel de control
4. Filtros de aceite de aluminio
5. Iluminación de la estufa
(Imagen 1)
(Imagen 2)
Modelo GDKP 2460 B
Tensión de alimentación
220-240V ~ 50 Hz
Potencia de la lámpara (W)
2 x 3 W
Potencia del motor (W)
210 W
Caudal (m³/h) - 3. Nivel
627 m³/h
Clase de aislamiento del motor Clas F
Clase de aislamiento Class I
GDKP 2460 B
504
598
53
Mn643 Max 1023
590
20
380
261
250
80 25