Caple MOT901 User manual

Instruction manual for COOKER HOODS
Contact Caple on 0117 938 7420 or for spare parts www.caple.co.uk
Instruction manual for deluxe electronic washing machine
Model code: WMi2004
Contact Caple on 0844 800 3830 or for spare parts www.4caple.co.uk
Model code: MOT901 Model code: LUC600
Model code: ZZ801 Model code: MOT912
www.caple.co.uk

2

GB The symbol on the product or on its packaging indicates that this product may not be
treated as household waste. Instead it shall be handed over to the applicable collection
point for the recycling of electrical and electronic equipment. By ensuring this product
is disposed of correctly, you will help prevent potential negative consequences for the
environment and human health, which could otherwise be caused by inappropriate
waste handling of this product. For more detailed information about recycling of this
product, please contact your local city oce, your household waste disposal service or
the shop where you purchased the product. This appliance is marked according to the
European directive 2012/19/EC on waste electrical and electronic equipment (WEEE).
3

CONTENTS
Warnings
Uses
Installation
Working
Maintenance
4
GB

5
* Please disconnect the appliance from power
mains, before carrying out any cleaning or
maintenance operation.
If the appliance is not equipped with a non-
separable flexible cable and plug, or with
another device ensuring omnipolar
disconnection from the mains, with an
opening distance between the contacts of
at least 3 mm, then such disconnecting
devices must be provided in the fixed
installation.
If the appliance is equipped with a power
cord and a plug, it shall be placed in such a
way that the plug can be reached easily.
* The use of materials which can burst into
flames should be avoided in close
proximity of the appliance. When frying,
please pay particular attention to fire risk
due to oil and grease. Being highly
inflammable, fried oil is especially
dangerous. Do not use uncovered electric
grills.
In order to avoid possible fire risk, all
instructions for grease-filter cleaning
and for removing eventual grease
deposits should be strictly followed.
WARNINGS
* The appliance is not intended for use by
young children or infirm persons without
supervision. Young children should be
supervised to ensure they do not play
with the appliance.
* The minimum distance between the
cooking surface and the lower part of
the cooker hood shall be 400 mm. For
LUC600 and ZZ801 MODELS, the minimum
distance shall be 650 mm.
*The extracted air can’t be conveyed
through or into a duct used to let out
fumes from appliances fed by energy
other than electric power (eg. centralized
heating, radiators, water heaters, etc.).
* To evacuate the air outlet, please comply
with the pertaining rules given by
competent authorities.
*Provide the room with an adequate aeration
when a cooker hood and appliances fed by
energy other than electric power (gas, oil, or
coal stoves, etc.) are used simultaneously. The
cooker hood, when evacuating the extracted
air, could generate a negative pressure in the
room which can’t exceed the limit of 0.04
mbar, in order to avoid the suck of exhausts
deriving from the heat-source. Therefore the
room should be provided with air-intakes to
allow a constant flow of fresh air.
If the rating label in the cooker hood
shows the symbol , the appliance is
built in class II° and it does not need any
earth connection.
If the rating label in the cooker hood does
not show the symbol , the appliance is
built in class I° and it needs the earth
connection.
* When performing the electrical connections
on the appliance, please make sure that the
current-tap is provided with earth connection
and that voltage values correspond to those
indicated on the rating label placed inside
the appliance itself.
USES
The appliance has been designed to
work both in recirculating and external
extraction modes.
* In the recirculation mode (fig. 1), the air and
fumes conveyed by the appliance are
purified by both a grease filter and an
activated charcoal filter, and then
recirculated back into the room through
the vent slots in the chimney. When the
appliance works in this mode, we
recommend the use of an air deflector
(Fig.1A) to be placed on the upper part of the
pipe, allowing the air to be re-circulated into
the room .
* In the External extraction mode (fig. 2),
fumes are directly conveyed outside the
building, through the top or rear air outlet.
The use of a charcoal filter and air
deflector is not necessary in this case.

6
INSTALLATION
MOT901 - MOT912 MODEL ONLY
Install no. 4 fixing screws on the
corresponding holes on the upper side of the
appliance (fig.7). Tighten the front screw
(fig.7A) to secure the appliance to the wall,
then check if the hood is perfectly leveled. If
it isn’t leveled tighten the back screws
(fig.7B): the right one to raise the right side of
the hood or the left screw to raise the left
side. Perform the electric connection.
Activate the glass panel lifting up, as shown
in the ‘Working’ section; when the panel is
completely open, which is done by setting the
IV speed, remove the grid as shown in (g.
8), then remove the grease lters and make
sure the hood is securely xed to the wall, by
using the inside screws (g. 9).
Reinsert the grease lters, the grid and close
the front panel by setting the OFF function, as
shown in the ‘Working’ section.
External extraction mode – upper outlet: Fix
the pipe bearing bracket to the wall and/or
ceiling by using the anchor screws and
screws provided (fig. 10), centered to the
hood.
Connect the motor air-outlet flange to the
exhaust hole, by using a suitable pipe. Place
the two ornamental pipes on the hood body;
lift the internal pipe up until it reaches the
ceiling; then fix it to the pipe bearing bracket,
by using the two self-threaded screws
provided.
External extraction mode - back outlet: Install
the air outlet grill above the hood in the
relative seat (refer to Fig. 11). The stainless
steel chimneys are not necessary.
Recirculation mode: Install the air outlet
grill above the hood in the relative seat
(refer to Fig. 11). The stainless steel
chimneys are not necessary.
In case that the appliance is used in the
Recirculation mode, it is necessary to install
the charcoal filters. First remove the metal
grease-filter, as indicated for each model in
the MAINTENANCE part, then place the
charcoal filter in its seat just behind the
grease filter.
LUC600 MODEL ONLY
Adjust the position of the hood horizontally
and vertically by acting on its screws through
its top hole, as per (fig. 12).
Remove the grease filter, held up by magnets,
by pulling it downwards (fig. 13).
Remove the front light panel (white), also
held up by magnets, by pulling it outwards
*Before installing the appliance, make sure
that none of the parts are damaged in any
way. In case of damaged parts, contact your
retailer and do not proceed with installation.
Read all of the following instructions carefully
before installing the appliance:
- Use an air outlet pipe of the shortest
possible length.
- Limit the number of pipe elbows.
- Use a material approved by standards and
regulations.
- Avoid any sudden changes in the pipe
section (recommended constant diameter: Ø
150 mm or equal surface area).
- The manufacturer shall not responsible for
air capacity or noise problems due to non
compliance with above mentioned
instructions, and no warranty shall be given.
The models MOT901, MOT912, ZZ801
have been designed in order to have the
possibility of directing the air outlet in the
rear side of the appliance; if you choose to
use this function, it is necessary to remove
the no. 10 screws of the motor unit support
(fig. 3), take out the motor unit and rotate it in
such a way to direct the air outlet nozzle
towards the rear side of the appliance (fig.
4); then place the motor unit in its seat
again and tighten the screws previously
removed.
By using its drilling template (fig. 5A), drill
the holes for the wall bracket installation;
The model MOT901, MOT912 shall be
installed at a minimum distance of 400mm
from the cooking surface. Assure a distance of
650mm from the cooking surface with
LUC600 model and ZZ801 model.
Fix the brackets to the wall, by using the
screw anchors and screws supplied with the
product;
Hang the body to the wall brackets previously
fixed (fig.6).

7
WORKING
sequentially by turning the knob ; the desired
function is set by pressing the knob.
- LIGHTS Indicator (fig. 18C)
This function allows you to switch the lights
on or off; turn the rotary control until the
function is selected, then set it by pressing
the rotary control.
- Timer Indicator (fig. 18D)
By setting this control, at any speed, the
appliance will be switched off after 10
minutes. It is necessary to select the control
again in order to exit from this function. .
When the Timer function is set , the Timer
indicator will flash and the corresponding
speed indicator is lit.
- Speed Indicators (fig. 18E)
They are lit accordingly to the speed set. OFF
Indicator (Fig.18F): This function allows
you to completely switch off the motor; it is
totally lit during selection and setting, while
it is in standby afterwards.
MOT901 - MOT912 Model (fig. 19)
This model, in addition to the working
features described in the paragraph above,
has an automatic opening and closing
system of the glass panel.
The opening of the glass panel corresponds to
and varies according to the motor speed set.
The panel is closed automatically, after the
motor is switched off.
A safety device reverses the panel direction in
case of impact with unusual surfaces during its
normal travel.
All of the appliances are equipped with an
electronic device allowing for automatic
switching o after four hour working from
the last operation performed.
Touch control (fig. 20)
A: Light switch On/O
B: Reduce speed / OFF motor
C: Motor speed display
D: ON motor/increase speed
E: 10 - minute timer
The touch control key allows the function
desired by touching the relative key.
If the electrical power supply to the product is
cut, 15 seconds are needed for self
diagnostics after the functions are restored.
In the meanwhile, its operation may be
incorrect.
(fig. 13), then disconnect the bipolar
electric connector. Insert the screw anchors
and screws provided in the holes indicated by
the arrows (fig. 14).
If the appliance is installed in the external
extraction mode, remove the grid covering the
motor air outlet (fig. 15).
Reinsert the grease lter and the l ight front
panel, making sure the electric connector is
connected properly.
ZZ801 MODEL ONLY
After the appliance is adjusted, fix it by
inserting and tightening the safety screws
properly (fig.16).
External extraction mode
Using the supplied wall plugs and screws, x
the tube support bracket (Des. 10) to the wall
and/or the ceiling. The bracket must be fixed
in a central position in respect of the air
outlet flange.
Connect the motor air outlet flange to the
exhaust hole, by using a suitable pipe.
Perform the electric connection. Place the
two ornamental pipes on the hood body; lift
the internal pipe up until it reaches the
ceiling; then fix it to the pipe bearing
bracket, by using the two self threaded
screws provided.
Perform the electric connection.
*Filtering version
Fix the air deflector to the pipe bearing
bracket, by using the screws provided.
Fix the pipe bearing bracket to the wall and/
or ceiling (Fig.17), centered to the hood.
Connect the motor air outlet flange to the air
deflector, by using a suitable pipe. Perform
the electric connection. Place the two
ornamental pipes on the hood body; lift the
internal pipe up until it reaches the ceiling;
then fix it to the pipe bearing bracket, by
using the two self threaded screws provided.
LUC600 - MOT901 Model (g. 18)
The rotary knob (g. 18A) allows you to select
the various functions of the appliance.
All the indicators (fig. 18B) are always lit in
the standby function ; functions are selected

8
MAINTENANCE
* If the appliance is used in the recirculation
mode, the activated charcoal filter needs to
be replaced periodically.
The charcoal filter is removed by removing
the grease filter first, following the
instructions above, then by pulling its
special plastic tongue until it is released
from its seat. The charcoal filter is inserted
by following the reverse procedure.
Tepid water and neutral detergents are
recommended to clean the appliance, while
abrasive products should be avoided.
The power cord shall be replaced by
authorized personnel only.
LED lamp replacement in LUC600 model:
Remove the two fixing screws (fig. 8) and
rotate the led light panel , as per (fig. 9).
Replace the damaged LED lamp with one of
the same kind.
Reinsert the led light panel and x it by using
the screws previously removed.
Replacement of the LED bar:
Using an appropriate tool, remove the LED
bar from its seat (refer to Fig. 21), disconnect
it electronically using the appropriate
connector then substitute it with a LED bar
with same characteristics.
Replacement Charcoal filters:
charcoal filters should be replaced every 6 months
or depending on use. Replacement charcoal filters
can be purchased on our website
www.caple.co.uk or by calling our sales office on
0117 938 1900.
An accurate maintenance guarantees
good functioning and long lasting
performance.
Particular care is due to the grease filter.
It can be removed by following the
instructions below:
MOT901, MOT912
Open the front glass panel by selecting the
maximum speed, remove the steel grid by
pulling it outwards (fig. 6), then act on the
filter handle and rotate it outwards.
LUC600, ZZ801
Remove the filter from the hood by pulling
it downwards (fig. 12).
Grease filters are inserted by following
the reverse procedure.
After 30 hour working, the grease filter
saturation will be signaled by the
simultaneous lighting of speed indicators;
select the timer function with the hood off
to reset it.
The grease filter needs cleaning by regular
hand washing or in dishwashers, every two
months at least, or depending on its use.
TIMING
As a result of the new EU65 “Energy label” and
EU66 “ Ecodesign” regulations issued by the
European Commission, which came into
force as from January 1st, 2015 , our
products have been adapted to comply with
these new requirements.
All of the models complying with the energy
label requirements, are equipped with new
electronics including a timer device for
suction speeds control, when the air capacity
exceeds 650m³/h.
Internal motor models, with maximum air
capacity higher than 650m³/h, are
equipped with a timer device that
automatically switches the suction speed
from 4th to 3rd speed, after 6 minutes
operation.
The energy consumption of the appliance in
standby mode is lower than 0.5W.

9
12
4
5
3
6
A
A
A
A
A

10
78
10
11
9
12

11
13 14
16
17 18
15

19 20
21
12

13

14

Serial number
Caple
Fourth Way
Avonmouth
Bristol
BS11 8DW
www.caple.co.uk
90042210076 - GM 04/15
90042210076 - 04/17