Grundig GDK 5782 B User manual

COOKER HOOD
GDK 5782 B
EN

Please read this user manual first!
Dear Customer,
Thank you for purchasing this Grundig product. We hope that you get the best results form your
product which has been manufactured with high quality and starte-of-the-art technology.
Therefore, please read this entire user manual and all other accompanying documents carefully before
using the product and keep it as a reference for future use. If you handover the product to someone
else, give the user manual as well. Follow all warnings and information in the
user manual.
Remember that this user manual is also applicable for several othet models. Differences between
models will be identified in the manual.
Please visit the “Support” section on the Grundig website
www.grundig.co.uk.to register your 5 year warranty.
Grundig Helpline
0845 603 1234
0345 603 1234

4
1 Warnings 6-7
2 Technical specification 8
General appearance . . . . . . . . . . . . . . 8
3 Installation 9-13
Electrical connection . . . . . . . . . . . . . . 9
Assembly . . . . . . . . . . . . . . . . . . . . . . 10
Mounting the hood body. . . . . . . . . . 11
Connections . . . . . . . . . . . . . . . . . . . . 11
Flue assembly. . . . . . . . . . . . . . . . . . . 13
Transportation . . . . . . . . . . . . . . . . . . 13
Disposal of packaging. . . . . . . . . . . . 13
4 Operating your
appliance 14
Touch control . . . . . . . . . . . . . . . . . . . 14
5 Maintenance and
cleaning 15-16
Cleaning the comfort panels . . . . . . . 15
Metal grease filter . . . . . . . . . . . . . . . 15
Carbon filter. . . . . . . . . . . . . . . . . . . . 15
Cleaning the hood . . . . . . . . . . . . . . . 16
Replacing the lamp . . . . . . . . . . . . . . 16
6 Troubleshooting
suggestions 17
7 Information 17
Technical data . . . . . . . . . . . . . . . . . . 17
Environmental note. . . . . . . . . . . . . . . 17
8 Guarantee 18
9 Service 19
TABLE OF CONTENTS ______________________________

5
________________________________________________________
3
4
2
1

6
WARNINGS _________________________________________
7 Do not operate the hood with-
out aluminum filters and do
not remove the filters while it
is operated.
7 This appliance shall be con-
nected to a grounded mains
outlet that is protected by a
fuse with proper capacity.
7 Do not plug in the hood be-
fore it is installed.
7 Do not touch the plug with wet
hands. Do not hold the cable
to remove the plug, always
pull out the plug by holding
the plug itself. Never use the
appliance if the plug or the
power cord is faulty.
7 Do not put power cord near
cooktops. This may cause a
fire as the cord may be melted.
7 Do not touch the lamps of the
hood after operating the hood
for a long time. Hot lamps may
burn your hand.
7 Do not operate the hood with-
out oil filter, otherwise internal
parts of the hood may get
dirty.
7 Overheated oil may splash
over the hood and may cause
a fire; therefore, do not leave
the hob unattended while fry-
ing. Be careful that the covers
and curtains do not catch a
fire.
Please review the following
information. Failure to com-
ply with these instructions may
cause risk of personal injury or
material damage. Any warran-
ty or commitment of reliability
shall be void.
7 This appliance is intended
for domestic use. The prod-
uct shall never be used for
any purpose other than its in-
tended use.
7 You may use a pipe with a di-
ameter of 120 mm on the flue
connection of your hood. Pipe
connection shall be as short as
possible and have minimum
number of elbows.
7 Do not make connections
to the flues connected with
stoves, exhaust shafts or flues
with rising flames.
7 The height between the lower
surface of the hood and upper
surface of the oven/hob
should not be less than 45 cm.
7 Turn on your hood after you
have placed the pot or pan
onto the burners in order to
prevent heat damage to your
hood. Turn off the burners
before taking a pot, pan etc.
from the burners when you are
done.

7
WARNINGS _________________________________________
7 Do not allow high flames under
the hood. Otherwise, oil in the
aluminum filter may ignite and
lead to a fire.
7 Do not keep easily flammable
materials under your hood.
7 There is a risk of fire if your
hood is not cleaned in the spec-
ified periods.
7 Operate your hood for 15 min-
utes more after the end of cook-
ing or frying in order to remove
unpleasant smell from the air in
the kitchen.
7 Ensure that fresh air enters the
kitchen, especially when the
hood is operated together with
the gas hobs.
7 If an appliance operated with
fuel oil or gaseous fuels (such
as room heaters) is available
in the environment where your
hood shall be operated, the ex-
haust of that appliance must be
fully isolated from the volume of
the room or the appliance must
be of hermetic type.
7 If there is non-electric appliance
in the same room with the hood,
the negative pressure inside the
room should be maximum 0.4
mbar to prevent the suction of
the waste gas from the other
appliance by the hood into the
room again.
7 Do not make connections
to the flues connected with
stoves, exhaust shafts or flues
with rising flames. Observe
the rules set by authorities on
the discharge of exhaust air.
7 Electrical appliances may be
risky for children. Keep the
children away from the unit
when it is operated, do not let
them play with the appliance.
7 Package materials may be
risky for children. Keep all
packaging materials away
from the children and dispose
them off by classifying them as
per the waste instructions.
7 The fan of the hood shall be
operated in the proper level
as required.

8
GDK 5782 B
Width 898 mm
Depth 380 mm
Height Min. 1055 - Max. 1330 mm
Supply voltage 220-240 V ~ 50 Hz
Control 4 positions
Suction power 740 m3/h
Control type Touch control
Motor power 250 W
Lamp power 3x20 W
Total power 310 W
Fuse 13 A
Air outlet pipe diameter 120/150 mm
Net weight 26.2 kg
Gross weight 33.8 kg
Color black glass
1
2
3
4
TECHNICAL SPECIFICATIONS _____________________
Specifications of the product may be modified without prior notification in order to increase
the product quality. Figures given in this manual are for schematic purposes only, and they
may not fully conform with the actual appliance.
Markings on the product or the values stated in other documents supplied with the product
are values obtained under laboratory conditions as per relevant standards. These values may
vary depending on the use of the product and ambient conditions.
General appearance
Hood body
Lighting
Control panel
Flue connection element

9
INSTALLATION _____________________________________
Note:
7 Preparation of the installation place and
electric wiring is the responsibility of the
customer.
Attention:
7 Assembly and electrical connections must
be carried out by specialized personnel.
7 Remove the protective film (if any) on the
hood and flue surface after the installation.
Electrical connection
The hood shall be connected to a grounded
mains outlet that is protected by a fuse with
proper capacity.
Attention:
7 Have a qualified electrician perform the
electric connection.
Important:
7 Connection shall comply with national regu-
lations.
7 The power outlet shall be reached easily
after installation.
7 Voltage and fuse protection allowed is
specified in “Technical Specifications.”
7 Specified voltage shall be equivalent with
your mains voltage.
7 Do not connect the appliance with exten-
sion cords or multiple outlets.
7 In case of direct connection to mains, con-
nect a 3-pole switch with a minimum contact
distance of 3mm between the appliance
and the mains.
7 Remove the grease filters making sure that
the connector of the supply cable is cor-
rectly inserted in the socket placed on the
side of the fan (Refer to Maintenance sec-
tion).
Attention:
7 Any damaged power cord shall be re-
placed by a qualified electrician.
7 Do not operate the appliance before it is
repaired! Risk of electric shock!

10
Assembly
Accessories and installation material
Ref Quantity Product materials
1 1
Hood Body and parts:
Controls, light, blower,
filters
2 1 Telescopic chimney
comprising of:
2.1 1 Upper section
2.2 1 Lower section
8 1 Air outlet grill
9 1 Reducer flange 150-
120 mm
10 1Damper 150
14.1 2Air outlet connection
extension
15 1 Air outlet connection
Ref Quantity Installation
materials
7.2.1 2 Upper chimney section
fixing brackets
7. 3 1Air outlet connection
support
11 6 Plugs
12a 6 Screws 4.2 x 44.4
12c 6 Screws 2.9 x 6.5
12e 2 Screws 2.9 x 9.5
Quantity Documentation
1 Instruction manual
INSTALLATION _____________________________________

11
Wall drilling and bracket fixing
7 Draw a vertical line on the supporting wall
up to the ceiling, or as high as practical, at
the center of the area in which the hood will
be installed.
7 Draw a horizontal line at 1040 mm above
the hob.
7 Place bracket (7.2.1) on the wall as shown
about 1-2 mm from the ceiling or upper limit
aligning the center (notch) with the vertical
reference line.
7 Mark the wall at the centers of the holes in
the bracket.
7 Place bracket (7.2.1) on the wall as shown
at X mm below the first bracket (X = height
of the upper chimney section supplied),
aligning the center (notch) with the vertical
line.
7 Mark the wall at the centers of the holes in
the bracket.
7 Mark a reference point at 116 mm from the
vertical reference as indicated.
7 Repeat this operation on the other side.
7 Drill 8 mm holes at all the center points
marked.
7 Insert plugs (11) into the holes.
7 Fix the lower bracket (7.2.1) using 12a
screws (4.2 x 44.4) supplied.
7 Fix the upper bracket (7.2.1) and the air
outlet connection support (7.3), together
using the 2 12a (4.2 x 44.4) screws sup-
plied.
7 Insert the two 12a (4.2 x 44.4) screws sup-
plied in the hood body fixing holes, leaving
a gap of 5-6 mm between the wall and the
head of the screw.
Mounting the hood body
7 Before mounting the hood body, tighten the
two screws (Vr) located on the hood body
mounting points
7 Hook the hood body onto the screws (12a)
7 Fully tighten the support screws (12a).
7 Adjust the screws (Vr) to level the hood
body.
Connections
INSTALLATION _____________________________________

12
Air outlet in ducted version
When installing the ducted version, connect
the hood to the chimney using either a flexible
or rigid pipe with a diameter 150 or 120mm
(the choice of which is left to the installer).
To install a pipe with a diameter of
150 mm:
7 To install the damper (10)
7 Fix the pipe in position using suitable pipe
clamps (not supplied).
To install a pipe with a diameter of
120 mm:
7 To install an air exhaust connection with
a diameter of 120 mm, insert the reducer
flange (9) onto the damper (10).
7 Fix the pipe in position using suitable pipe
clamps (not supplied).
7 Remove carbon filters if any.
Usage with carbon filter
7 Cut a hole with a diameter of 125 mm in
any shelf that may be positioned over the
hood.
7 Insert the reducer flange (9) on the hood
body outlet.
7 Connect the flange to the outlet on the shelf
over the hood using a flexible or rigid pipe
with a diameter of 120 mm.
7 Fix the pipe in position using suitable pipe
clamps (not supplied).
7 Fix the grille (8) which can be installed only
in one direction on the recirculation air out-
let using the 2 12e (2,9 x 9,5) screws.
7 Ensure that the carbon filters have been in-
serted.
Usage with carbon filter
7 Insert the Connector (15) into the Support
bracket (7.3) and fix it with a screw.
7 Insert the connection extension pieces later-
ally (14.1) in connection (15).
7 Make sure that the outlet of the extension
pieces (14.1) is horizontally and vertically
aligned with the chimney outlets.
7 Connect the air outlet connection (15) to
the hood body outlet using either a flexible
or rigid pipe with a diameter of 150 mm
(the choice of which is left to the installer).
7 Ensure that the carbon filters have been in-
serted.
INSTALLATION _____________________________________

13
Flue assembly
Upper flue ;
7 Slightly widen the two sides of the upper flue
and hook them behind the brackets (7.2.1),
making sure that they are well seated.
7 Secure the sides of the brackets using the 4
12c screws (2.9 x 9.5) supplied.
7 Make sure that the extensions pieces are
aligned with the flue outlets.
Lower flue ;
7 Slightly widen the two sides of the flue and
hook them between the upper flue and the
wall, making sure that they are well seated.
7 Fix the lower part laterally to the hood body
using the 2 12c (2.9 x 9.5) screws supplied.
Transportation
Disconnect the appliance from mains supply
and remove the hood first if you need it to be
transported. Transport the appliance with its
original package if possible, and observe the
transport markings on the original package.
If the original package is not available, pack
the appliance so that it will not be damaged.
Disposal of packaging
Package materials may be risky for children.
Keep all packaging materials away from the
children and dispose them off by classifying
them as per the waste instructions. Do not dis-
pose of with regular household waste.
Package of your product is made of recycla-
ble materials.
INSTALLATION _____________________________________

14
Use the high suction speed in cases of con-
centrated kitchen vapors. It is recommended
that the cooker hood suction is switched on
for 5 minutes prior to cooking and to leave
in operation during cooking and for another
15 minutes approximately after terminating
cooking.
A. Switches the extractor motor on and off
at the latest selected speed. Indicates the
selected speed on the screen.
B. Decreases the suction speed. The number
of LEDs lit on the screen decreases.
C. Decreases the suction speed. The number
of LEDs lit on the screen increases.
D. Auto-Off intense ventilation: By
pressing this key it is possible to start the
intensive speed from any previously select-
ed speed except the Auto-off or air clean-
ing function. This speed has been timed
at 10 minutes. After that time the system
automatically activates the latest selected
speed. This function is suitable for cooking
conditions when vapours and smells are at
maximum level. “I” flashes on the screen
and all LEDS are lit. Press this key to stop
the function.
E. Air cleaning feature: By pressing this
key it is possible to set up the motor to a
suction speed at 100 m3/h . 24 appears
and the LEDs extinguish one by one. Press
this key to stop the function.
F. Automatic shutdown: By pressing this
key it is possible to set the automatic shut-
down of the motor and the lighting to 30
minutes.
This function is suitable for a complete
elimination of residual cooking odours.
Only operates when the motor is on (not
while the air cleaning or intensive venti-
lation function is active). Press this key to
stop the function. A flashing clock-symbol
appears. Press this key to stop the function.
G. Filter saturation indicator: By press-
ing this key for about 2 seconds it is pos-
sible to reset the filter saturation alarm.
After 100 working hours a drop-symbol
appears. Metal grease filters have to be
washed. While using with a carbon fil-
ter, after 200 working hours C appears.
Carbon filters have to replaced in this
case.
H. By pressing this key the intensity of the
light can be decreased.
I. Turns the lighting system on and off at
maximum intensity.
L. By pressing this key the intensity of the
light can be increased.
Key panel lock
it is possible to lock the key panel when, for
example, cleaning the glass. The motor and
lights are switched off.
By pressing the F-key (auto-off) for about 5
seconds the key panel can be activated or
deactivated. This function is confirmed by a
beep and by moving motor LEDs on display.
Touch control
OPERATING YOUR APPLIANCE __________________

15
MAINTENANCE AND CLEANING _________________
Before all maintenance and cleaning opera-
tions, remove the plug of the appliance or turn
off or remove the fuse!
Service your hood periodically!
Service is also required to prevent burning of
oil filter besides obtaining better performance
and better efficiency.
Cleaning the comfort panels
7 Pull the comfort panels to open them.
7 Disconnect the panel from the hood canopy
by sliding the fixing pin lever.
7 The comfort panel must never be washed in
a dishwasher.
7 Clean the outside using a damp cloth and
neutral liquid detergent.
7 Clean the inside as well using a damp cloth
and neutral detergent; do not use wet cloths
or sponges, or jets of water; do not use
abrasive substances.
7 When the above operation has been
completed, hook the panel back to the
hood canopy and close it by turning the
knob in the opposite direction.
Metal grease filter
Filters can be washed in the dishwasher.
Metal filters need to be washed every time
a drop-symbol appears in the display or at
least every 2 months. Hood shall be cleaned
more often when it is used more frequently.
Alarm reset:
Press the “G” key for at least 2 seconds.
Cleaning the filters
7 Pull the comfort panels to open them.
7 Remove the filters one by one pushing them
towards the back side of the hood unit and
simultaneously pulling downwards.
7 Any kind of bending of the filters has to be
avoided when washing them. Before fitting
them again into the hood make sure that
they are completely dry. (The colour of the
filter surface may change throughout the
time but this has no influence to the filter
efficiency).
7 When fitting the filters into the hood pay
attention that they are mounted in correct
direction with the handles facing outwards.
7 Close the comfort panel.
Attention:
7 Remove the filters one by one pushing them
towards the back side of the hood and
simultaneously pulling downwards and
towards the center of the hood.
Carbon filter
This filter cannot be washed or regenerated.
It must be replaced when the C appears on
the display or at least once every 4 months.
The filter saturation alarm has to be activated
before.
Activating the alarm signal:
7 In the recirculation version hoods the filter
saturation alarm must be activated during
the installation or later.
7 Switch off the hood and the lighting.
7 Press the “E” key for about 5 seconds until
the last two segments of the motor LEDs are
lit on the display.
7 By releasing the “E” key the clock icon starts
to flash.

16
MAINTENANCE AND CLEANING _________________
7 Within 3 seconds press the “D” key to
activate/deactivate carbon filter saturation
alarm.
7 “C” symbol lit - carbon filter saturation
alarm ACTIVATED.
7 “C” symbol unlit - carbon filter saturation
alarm DEACTIVATED.
Replacing the carbon filter
Resetting the alarm signal:
7 Switch off the motor and the lighting system.
7 Press the “G” key for at least 2 seconds.
Replacing the filter:
7 Open the comfort panel.
7 Remove the metal grease filters.
7 Remove the carbon filter as indicated in the
picture.
7 Place the filter again into its seat.
7 Place again the metal grease filters into their
places.
Cleaning the hood
7 Hood must only be cleaned when it is
unplugged from mains outlet or when the
fuse is switched off!
7 Hood must not be cleaned with a vapor
cleaner as it not ensured that it would operate
safely afterwards due to water vapor.
Outer surfaces of the hood must be cleaned
with a mild cleaning agent (e.g. dish soap).
Do not use strong cleaning agents, abrasive
agents or sharp objects.
Stainless steel surfaces shall be cleaned with
a commercially available stainless steel clean-
ing agent and a soft, non-abrasive sponge or
cloth. In order to prevent scratches, wiping
action shall be performed on the direction of
surface structure while you are cleaning the
stainless steel surfaces.
Replacing the lamp
7 Remove the 2 screws fixing the lighting
support, and pull it out of from the hood.
7 Remove the lamp from the support.
7 Replace with another of the same type,
making sure that the two pins are properly
inserted in the lamp holder socket holes.
7 Install the support, fixing it in place with the
two screws removed in previous steps.

17
TROUBLESHOOTING SUGGESTIONS ____________
Problem Explanation / Suggestion
Hood operates incorrectly Turn off the hood with keys and cut off electricity supply for a
few seconds by removing the plug or closing the fuse.
Hood does not operate
∑ Is the plug connected to mains outlet?
∑ Is the fuse in the household installation burnt off?
∑ Did you press the fan keys?
Suction power of the hood
is inadequate
∑ Is the correct fan level set?
∑ Is the oil filter or carbon filter cleaned in time?
∑ Is the air taken from the kitchen compensated with
adequate amount of fresh air to prevent vacuuming?
Operating noise increased
in the course of time
Have you conformed with the maintenance intervals of the
filters; i.e. is any air passage possible?
Illumination is disabled
∑ Is the fuse in the household installation burnt off?
∑ Is the lamp faulty?
∑ Is the new lamp seated correctly?
Filter saturation indicator
flashes or lights up
continuously
Refer to “Maintenance and cleaning” section for the oil filter
or carbon filter saturation indicator.
INFORMATION ____________________________
Environmental note
The symbol on the product or on its
packaging indicates that this product
may not be treated as household waste.
Instead it shall be handed over to the ap-
plicable collection point for the recy
cling of electrical and electronic equip-
ment. By ensuring this product is disposed of cor-
rectly, you will help prevent potential negative
consequences for the environment and human
health, which could otherwise be caused by inap-
propriate waste handling of this product. For more
detailed information about recycling of this prod-
uct, please contact your local city office, your
household waste disposal service or the shop
where you purchased the product.
This product conforms to European
Directives 2004/108/EC,
2006/95/EC, 2009/125/EC and
2011/65/EU.
Power supply
Operating voltage: 220-240V~, 50Hz
Technical and design modifications reserved!

GUARANTEE _______________________________
Guarantee for Refrigeration, Cooking Appliance, Washing Machines & Dishwashers
Your new Grundig product is guarenteed against the cost of breakdown repairs for 5 years from the daie
of the orginals purchase.
“Please visit the “support” section on the Grundig website at www.grundig.co.uk to
register your 5 year warranty.
What is covered?
• Repairs necessary as a result of faulty materisals, defective components or manufacturing defect.
• The cost of functional replacement paris, but excluding consumable items.
• The labour costs of a Grundig approved repairer to carry out the repair.
What is note covered?
• Transil, delivery or accidental damage or misuse and abuse.
• Cabiner or appearance parts, including knobs, flobs, handles or container lids.
• Accessories or consumable items including but not limited to, ice trays, scropers, cutlery baskets, filiers
and light bulbs.
• Repairs required as a result of unauthorised repair or inexport installation that fails to meet the
requirements contained in the user instruction book.
• Repairs to products used on commercial or non residential household premises.
• Loss of frozen food in freezers or fridge/freezers. (Food loss insurance is often inckuded within your
household contents insuarence policy, or may be available separately from your retailer.)
Important notes
• Your Grundig product is designed and built for domestic household use only.
• the guarantee will be vold if the product is installed or used in commercial or non-residential domestic
household premises.
• The product must be correctly insalled, located and operated in accordance with the instructions
contained in the User Instructions Booklet provided.
• Professional installation by a qualified Electrical Domestic Appliance Insttaller is recommended for all
Washing Machines, Dishwashers and Electric Cookers
• Gas Cookers must only be installed by a Gas Safe (or BORD GAIS) registered Gas Intaller.
• The guarantee is given only within the boundaries of the United Kingdom and the Republic of Ireland.
• The guarantee is applicable only to new products and is note transferable if the product is resold.
• Grındig disclains any liability for incidental or consequential damages.
• The guarantee does not in anyway diminsh your statutory or legal rights.
Should you experience any difficulty in obtaining service please contact the Grundig Customer Helpline.
Tel : [phone]
0345 603 1234
e-mail : ser[email protected]

Service ____________________________________
Please keep your purchase receipt or other proof of purchase in a safe place; you will need to have it
should the product require attention under guarantee.
You should also complete the details below; it will help us assist you when requesting service. (The model
number is printed on the Instruction Booklet and the serial number is printed on the Rating Label affixed
to the appliance)
Model No:
Serial No:
Retailer:
Date of purchase:
For service under guarantee simply telephone the appropriate number below UK
Mainland & Northern Ireland
0845 603 1234
0345 603 1234
Republic of Ireland
All Refrigeration, All Cookers
Washing Machines and Dishwashers
01 862 34 11
Before requesting service please check the trouble- shooting guide in the Operating
Instructions as a charge may be levied where no fault is found even though your
product may still be under guarantee. Service once the manufacturers guarantee has
expired.
If you have purchased an exlended guarantee please refer to the instructions
contained within the extended guarantee agreement document. Otherwise please
call the appropriate number above where service can be oblained at a charge.
Grundig, 1 Greenhill Crescent, Watford Herts WD18 8QU

FOR A GOOD REASON