GT-Lite GT-421CP-S User manual

•Do not submerge this fixture in water or other liquids.
•Do not use with extension cord near water or where water may
accumulate.
•Keep light at least 16 feet from pools and spas. Keep plugs and
receptacles dry.
•Avoid electrical shock by turning off or disconnecting from power while
moving or installing the unit.
•When using product, basic precautions should always be followed.
•Read and follow these instructions and observe all warnings.
•Carefully read and understand the information given in this guide before
using this light. Failure to do so could lead to electrical shock, fire, or
other injuries which could be hazardous or even fatal.
•Save this User Guide.
•Do not use on radiant heated ceiling.
•Do not use in areas with temperature higher than 104° Fahrenheit.
•Use carabiner clip to hang. Do not use electrical cord for mounting.
•Do not use in areas near a gas source. This light is not for use in
potentially explosive environments. This is not a vapor proof light.
•This light is not a toy and is not suitable for use by children.
•Protect your eyes. Do not look directly at the LED lights for extended
periods of time.
•Do not remove the lens protecting the LED. It is not possible to change
the LED light source. The LED chips are not replaceable.
•Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
•Disassembling or modifying this unit will void the warranty.
GT-421CP-S
1500 Lumen LED 10ft String Light with Adjustable Light Head
GT-LITE WARRANTY: This product is guaranteed against failure
due to factory defects in materials or workmanship for one (1) year
from the date of purchase. This warranty is non-transferable and
applies only to the original owner. Proof of purchase required for
repair or replacement. Keep product receipt with this User Guide
and save in a dry location.
The warranty does not cover normal wear and tear of parts or
damage resulting from misuse of the product. Misuse of the product
includes but is not limited to: using in extreme weather conditions,
opening the housing of the product, or attempted
remodel/alterations to the product.

STRING LIGHT CONSTRUCTION:
AA. Power Cord (Male End)
BB. Connection between 10ft strings
CC. Power Connection (Female End)
DD. Adjustable Plastic Strap
EE. Carabiner Clip
FF. Pivoting Socket
GG. Light Head
TO USE
1. Hang light head (GG) using carabiner clip (EE) or adjustable
strap (DD) where light is needed. Use individually or linked.
a. Do not use electrical cord to hang.
b. It is recommended to hang light head at approximately
10ft height for optimal light coverage.
c. Plastic strap (DD) can be secured at different slots to best
fit the width of board. Do not use plastic strap on hot
surfaces such as water pipes.
2. Rotate light head at the pivoting socket (FF) until it is pointing
to the intended area.
3. If desired, link additional 10ft strings by inserting male end
(AA) of additional string into connecting female end (CC) of
previous string. Up to 45 lights (450 feet) can be connected
on one power outlet.
a. Always ensure connection between strings (BB) is secure.
b. When not in use, use plastic flap to close female end of
power cord (CC) to help keep out dust and moisture.
4. Continue steps 1, 2 and 3 until all lights/strings are mounted
as desired.
5. Plug in male end (AA) power cord into outlet.
6. All lights will illuminate immediately.
7. Unplug lights from power when moving the light heads or
adjusting the carabiner clip or plastic strap.
TROUBLESHOOTING
Problem
Cause
Solution
Lights are not
lighting up.
No power or faulty
connection.
Check that all
connections (BB)
are secure, and
power is ON.
Other issue
-
Contact GT-Lite
CARE AND CLEANING
Your fixture is made from quality materials that will last an
extended period of time with proper care. Periodically clean the
surface of the fixture.
1. Use a mild, non-abrasive cleaner. Do not use any solvents or
harsh cleaning agents.
2. Use a soft, non-abrasive cloth.
3. Lightly spray cleaner onto the cloth. Do not spray liquid
cleaners directly onto LEDs, power cord, or any part of this
product.
4. Lightly wipe down fixture with damp cloth. Allow product to dry
completely before restoring power and using LED lights.
AA CC
BB
EE
FF
GG
DD
Looking for dependable work lights? Rely on GT-Lite for quality and long-lasting products.