GT-Lite GT-507-U User manual

• Do not submerge this fixture in water or other liquids.
• Do not use with extension cord near water or where water may
accumulate.
• Keep light at least 16 feet from pools and spas. Keep plugs and
receptacles dry.
• Suitable for Damp Locations only.
• Avoid electrical shock by turning off or disconnecting from power
while moving or installing the unit.
• When using product, basic precautions should always be followed.
• Read and follow these instructions and observe all warnings.
• Carefully read and understand the information given in this guide
before using this light. Failure to do so could lead to electrical shock,
fire, or other injuries which could be hazardous or even fatal.
• Save this User Guide.
• Do not use in areas with temperature higher than 104° Fahrenheit.
• Do not use in areas near a gas source. This light is not for use in
potentially explosive environments. This is not a vapor proof light.
• This light is not a toy and is not suitable for use by children.
• Protect your eyes. Do not look directly at the LED lights for
extended periods of time.
• Do not remove the lens protecting the LED. It is not possible to
change the LED light source. The LED chips are not replaceable.
• Changes or modifications to this unit not expressly approved by the
party responsible for compliance could void the user’s authority to
operate this equipment.
• Disassembling or modifying this unit will void the warranty.
GT-507-U
5,000 Lumen LED Portable Work Light with USB Port
GT-LITE WARRANTY: This product is guaranteed against
failure due to factory defects in materials or workmanship for
one (1) year from the date of purchase. This warranty is non-
transferable and applies only to the original owner. Proof of
purchase required for repair or replacement. Keep product
receipt with this User Guide and save in a dry location.
The warranty does not cover normal wear and tear of parts or
damage resulting from misuse of the product. Misuse of the
product includes but is not limited to: using in extreme weather
conditions, opening the housing of the product, or alterations to
the product.

WORK LIGHT CONSTRUCTION:
A. Carrying handle with comfort grip
B. Lightweight, scratch-resistant aluminum frame
C. Tiltable light face
D. LEDs
E. Tempered glass protective lens
F. Tangle-free grounded power cord
G. Side star knobs (2)
H. On/Off switch
I. USB port
J. U-frame
K. Base knob (1)
L. H-stand base
M. Textured rubber feet for strong surface grip
ASSEMBLY:
1. Attach U-Frame (J) to H-Stand (L) by screwing Base Knob
(K) completely through the holes on (J)+(L) until tight.
TO USE:
1. Place H-Stand (L) on a sturdy surface. Ensure that all 4
Rubber Feet (M) have a secure grip on the surface.
2. Slightly loosen side Star Knobs (G)(do not unscrew
completely).
3. Tilt Light Face (C) up or down to the desired angle.
4. Tighten Star Knobs (G).
5. Slightly loosen Base Knob (K)(do not unscrew completely).
6. Swivel U-Frame (J) side to side to the desired angle.
7. Tighten Base Knob (K).
8. Plug Power Cord (F) into outlet.
9. To turn light on, switch On/Off (H) to On position (–).
10. To turn light off, switch On/Off (H) to Off position (o).
11. To charge a device, plug device into USB port (I). USB port
works with LED light on or off, as long as the unit is plugged
into power outlet.
12. Store in a cool dry place when not in use.
TROUBLESHOOTING
Problem
Cause
Solution
LED is not
lighting up.
No power or faulty
connection.
Check that all
connections are secure,
and power is ON.
Questions,
Missing Parts
Customer Service:
1-800-865-6799
CARE AND CLEANING
Your fixture is made from quality materials that will last an
extended period of time with proper care—including periodically
cleaning the surface of the fixture.
1. Use a mild, non-abrasive cleaner. Do not use any solvents or
harsh cleaning agents.
2. Use a soft, non-abrasive cloth.
3. Lightly spray cleaner onto the cloth. Do not spray liquid
cleaners directly onto LEDs, power cord, or any part of this
product.
4. Lightly wipe down fixture with damp cloth. Allow product to dry
completely before restoring power and using LED lights.
NOTICE: This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful interference
to radio or television reception, which can be determined by turning the equipment off and on, the user
is encouraged to try to correct the interference by one or more of the following measures: (1) Reorient
or relocate the receiving antenna. (2) Increase the separation between the equipment and receiver. (3)
Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
(4) Consult the dealer or an experienced radio/TV technician for help.
A
B
C
D
E
F
G
H
J
I
K
L
M