GTD GTD-LYS300 User manual

LED Fresnel Spotlight
GTD-LYS300 (CW/WW)
User’s Manual
Guangzhou GTD Lighting Technology Co., Ltd.
Tel: [phone]
Fax: [phone]
http://www.gtd-lighting.com

GTD-LYS300 (CW/WW) User Manual
1
© 2017 GTD all rights reserved. Information, specifications, diagrams, images, and instructions herein are subject to
change without notice. GTD logo and identifying product names and numbers herein are trademarks of GTD. Copyright
protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or
judicial law or hereinafter granted. Product names used in this document may be trademarks or registered trademarks of
their respective companies and are hereby acknowledged. All non-GTD brands and product names are trademarks or
registered trademarks of their respective companies.
GTD and all affiliated companies hereby disclaim any and all liabilities for property, equipment, building, and electrical
damages, injuries to any persons, and direct or indirect economic loss associated with the use or reliance of any
information contained within this document, and/or as a result of the improper, unsafe, insufficient and negligent
assembly, installation, rigging, and operation of this product.
Guangzhou GTD Lighting Technology Co., Ltd. | 27 Fu Yuan Yi Road, Guangzhou 510805, P.R.China
[phone] | [phone] fax | www.gtd-lighting.com | [e-mail]

GTD-LYS300 (CW/WW) User Manual
2
Contents
Safety instructions...................................................................................................................................................................... 3
General guidelines...................................................................................................................................................................... 4
Packing and shipping .................................................................................................................................................................. 5
Unpacking ....................................................................................................................................................................................... 5
Packing after use............................................................................................................................................................................. 5
Accessories................................................................................................................................................................................. 5
Product introduction .................................................................................................................................................................. 6
Installation ................................................................................................................................................................................. 6
Clamps installation ......................................................................................................................................................................... 6
Device installation .......................................................................................................................................................................... 6
Power / Control connection ....................................................................................................................................................... 7
Power connection........................................................................................................................................................................... 7
Control connection ......................................................................................................................................................................... 7
Testing ............................................................................................................................................................................................ 7
Control panel.............................................................................................................................................................................. 8
Menu structure .......................................................................................................................................................................... 8
DMX protocol............................................................................................................................................................................. 9
Technical specification ............................................................................................................................................................. 10
Cleaning and maintenance ....................................................................................................................................................... 11
Troubleshooting ....................................................................................................................................................................... 12
System wiring diagram ............................................................................................................................................................. 14
Spare parts list ......................................................................................................................................................................... 14
Appendix 1 ............................................................................................................................................................................... 15

GTD-LYS300 (CW/WW) User Manual
3
Safety instructions
WARNING!
Before using the fixture, read the latest version of the product user manual, paying particular attention
to the safety instructions. Please check www.gtd-lighting.com for the latest revision/update of the user
manual. The manufacture of this fixture, are not responsible for damages, resulting from misuse of this
fixture, due to the disregard of the information printed in this user manual.
DANGER!
Hazardous voltage. Risk of lethal or severe electric shock.
WARNING!
Burn hazard. Hot surface. Do not touch.
WARNING!
Fire hazard.
INDOORS USE ONLY!
Do not expose fixture for rain and moisture.
It’s essential that the fixture is properly grounded. Only qualified personnel should perform electrical
connections.
WARNING!
Wear protective eyewear. Never look directly into the light source.
Only qualified and certified personnel should perform installation of this fixture and only the original rigging parts
(brackets) included with this fixture should be used for installation.
Before applying power to the fixture, check that the source voltage matches the fixture's requirement. Every fixture
must be earthed (grounded) and installed in accordance with local electricity regulations. Do not connect it to a
dimmer system.
Never look directly into the light source of this fixture to prevent risk of injury to your retina, which may induce
blindness.

GTD-LYS300 (CW/WW) User Manual
4
General guidelines
Never open this fixture while in use.
The fixture should be kept clean. DO NOT operate the fixture in extreme heat or dusty environments. Avoid contact
with chemical liquid.
This fixture is a professional light effect designed for INDOOR / DRY LOCATIONS ONLY on stage, in nightclubs,
theatres, etc.
Minimum distance to lighted objects must be 3.28feet (1m).
Maximum temp of the external surface 140˚F (60˚C).
Maximum ambient temperature 113˚F (45˚C).
Minimum distance of inflammable materials from the surface 1.6 feet (0.5m).
The light source of the fixture should be changed by the manufacture or its service agent or certified technicians.
WARNING! Risk of electric shock.
The basic insulation should be kept between the controllable device and the power supply.
Cover, lens or Menu Function Display with visible damages such as cracks or scratches must be replaced to ensure
performance of the fixture.
Disconnect the fixture from power before changing any parts or accessories.
Make sure that the installation area can hold a minimum point load of 10 times the weight of all installed fixtures,
clamps, cables, auxiliary equipment, etc. Check that the cover, clamps and locks are undamaged. Certified safety
cables must always be used when installing the fixture.
The fixture is only intended for installation, operation and maintenance by qualified professional. Instructions
stated in the manual must be complied.
The fixture must be kept in a well-ventilated place at least 50 cm away from any wall surface. Check if the fans or
ventilation openings are unblocked.
Broken or damaged cables can only be fixed or changed by certified technicians, certified local distributors or the
manufacturer to ensure operational safety.
Do not stick filters or other materials onto the lens. Do not modify the fixture or install other than GTD
manufactured parts.
For questions regarding safety operation, please contact our technical personnel or call the service hotline +8620
61808296.

GTD-LYS300 (CW/WW) User Manual
5
Packing and shipping
Unpacking
Notes
All products are quality controlled and checked for any faults before they are dispatched to customers. If the fixture is
damaged during delivery, the customer must notify the shipper and manufacturer to file a damage insurance claim.
Photographic evidence of the damage must be provided.
Flight-Case
Open the cover of the flight-case and remove the plastic packing bags. Hold the handles of the fixture firmly and take it
out carefully.
Cardboard box
Open the box and take out the whole set of packaging foam which contains both the fixture and its accessories. Remove
the foam from the top, put away the accessories, and then take out the fixture wrapped in the plastic bag.
Packing after use
1. Switch off the fixture and wait for at least 5 minutes before disconnecting it from AC power. Cool down the fixture for
at least 15 minutes before packing.
2. Flight case: Wrap the fixture in plastic bags. Hold it by the handles, and then carefully place it inside the flight case
along with all the accessories. Close the cover. Only 3 layers are allowed when piling up the flight cases. Do not
upside down.
Cardboard box: Wrap the fixture in plastic bags. Put it in the packaging foam along with all the accessories. Place the
other set of packaging foam on top then carefully put it inside the cardboard box.
Accessories
Item
Qty
Unit
Notes
User Manual
1
pc
-
Clamp
1
set
Ø42-52mm, Max. 200 kg
safety cable
1
pc
Signal lines
1
pc
5m
Power cable
1
pc
Without the power cable when the lamp with the lead line;
Notes
Accessories are subject to change without any prior written notice.

GTD-LYS300 (CW/WW) User Manual
6
Product introduction
1 Hanging rack
2 Adjustable screw
3 Block Light leaf
4 Corrugated Mirror
5 Display
6Adjustable screw
7 DMX output
8 DMX input
9 power cable
10 Power switch
11 fuse
12 Adjustable screw
Installation
Clamps installation
The fixture can be placed on the stage or mounted on the truss facing any direction. The fast-lock clamp gives a quick and
easy lock on the truss.
Warning
Use one clamp when mounting the fixture. Fasten the screw properly and connect a safety cable to fixture.
Device installation
1. Make sure there is no damage on the clamps or safety cables before installation.
2. The clamp is mounted on the handle of the fixture. Horizontally insert the clamp into the mounting holes of the
handle. Fasten the clamp tightly.
(The actually clamp may be different from below picture. Please refer to the actual product.)
1
2
3
4
5
6
7
8
9
10
11
12

GTD-LYS300 (CW/WW) User Manual
7
Power/ Control connection
Power connection
Connection method:
L (Live) Brown wire
E (Earth) Yellow / Green bi-color wire
N (Neutral) Blue wire
The voltage and frequency of the power source must be in compliance with the ones marked on the fixture. It is
strongly recommended that each fixture are to be connected to the power source separately so that they can be
switched on / off individually.
Notes
It is essential that each fixture is correctly grounded and the electrical installation conforms to all relevant Standards /
Codes of Practice for Safe Electrical Work.
Control connection
The fixture has 5-pin XLR connectors for DMX data input and output (3-pin optional) as shown below. Connection between
the console and fixture, and between fixtures must be made with 2 core screened DMX signal cable. Maximum connecting
distance of signal cable is 150 meters. Additional DMX512 signal-amplifier is recommended for longer distance.
Connect the Console’s DMX OUTPUT to the first fixture’s DMX INPUT, then the first fixture’s DMX OUTPUT to the second
fixture’s DMX INPUT and so on. It is recommended not to connect more than 32 units on a single DMX universe. On the
last fixture‘s output connect a DMX terminator. (The terminator is a XLR connector with a ¼ W and 120Ω resistor between
the pin 2 and pin 3) as shown below:
Testing
Connect the fixture to AC power. Check if the LED lamp is on and the fixture is independently controllable before putting
into operation.
Console Input DMX terminator
Output Input Output Input Output

GTD-LYS300 (CW/WW) User Manual
8
Control panel
m
1
The control panel with buttons and digital display can access the function menu and configure the fixture easily.
Press MENU to check or modify the functions of the fixture; Press UP or DOWN to view or select the function
menu.
Press ENTER to choose a function and enter into corresponding sub menu. Each menu represents a specific
function of the fixture.
Press ENTER to select the specific function and save the changes or enter into the submenu, then press UP or
DOWN to change the value of the selected function (increase or decrease).
Press MENU to return to the previous menu or exit.
LED indicators:
Power on: RED power LED indicator on
Signal on: Green DMX indicator on
No Signal: Green DMX indicator off
Menu structure
LYS300 –Menu Structure
Level 1
Level 2
Level 3
Level 4
Info
Run setting
Address Setting
Address: 001~ XXX
Setting the DMX address
Device Info
Time Info
This Time
Total Time
Last Time
Lamp On Time
Lamp Off Time
XXXXXX Hour
XXXXXX Hour
XXXXXX Hour
XXXXXX Hour
XXXXXX Minute
Since power on time
Product total run time
Last product run time
Lamp on time
Lamp close time
Temperature
Body Temperature
XXX ℃
Body temperature
Software Version
X.X
The software version

GTD-LYS300 (CW/WW) User Manual
9
System Setting
Value Setting
Dimmer
Zoom
Dimmer =0~255
Zoom=0~255
Dimmer channel value
Zoom channel value
Dimmer Mode
M0:600hz Fade
M1:600hz Snap
M2:1200hz Fade
M3:1200hz Snap
M4:600hz Fade
M5:600hz Snap
Dimmer Mode Set
Display Setting
Backlight Time
1~80 Min/Disable
Set backlight off time
Reset
System Reset
System reset
Channel Setting
Channel Mode
Simplified Mode
Standard Mode
Simplified channel mode
Standard channel mode
DMX protocol
Revision: A
Valid from firmware version: 1.0
DMX mode
Name
DMX
value
DMX
percentage
Function
Default
DMX
Value
Standard (4ch)
1
Intensity
0
255
0.0%
100.0%
No light Full light
0(0%)
2
Zoom
0
255
0.0%
100.0%
Near Far
0(0%)
3
Dimmer Mode
0
5
0.0%
2.0%
M0.600Hz, Dimming curve1, fade dimming
0(0%)
6
11
2.4%
4.3%
M1.600Hz, Dimming curve2, snap dimming
12
17
4.7%
6.7%
M2.1200Hz, Dimming curve1, fade dimming
18
23
7.1%
9.0%
M3.1200Hz, Dimming curve2, snap dimming
24
29
9.4%
11.4%
M4.600Hz, Dimming curve1, fade dimming
30
35
11.8%
13.7%
M5.600Hz, Dimming curve2, snap dimming
36
255
14.1%
100.0%
Reserved
4
Special controls
0
59
0.0%
23.1%
Dimmer intensity
0(0%)
60
89
23.5%
34.9%
System reset after 5 seconds
90
129
35.3%
50.6%
Dimmer intensity and Zoom function
130
239
51.0%
93.7%
No function
240
249
94.1%
97.6%
Save dimmer mode after 5 seconds
250
255
98.0%
100.0%
No function

GTD-LYS300 (CW/WW) User Manual
10
Technical specification
Optical
Light source: LED 300W, quantity: 1 piece（CW/WW）
Expected average lifetime: 50000 hours
Beam angle (zoom): 20.9° - 49.3°
Photometric
Color temperature: 5400K~5800K(CW) / 2800K~3200K(WW)
CRI: >96Ra
Electrical
Power input, nominal: AC 100-240V, 50/60Hz
Max. Power consumption: 313W, max current: 3.1A, PF≥0.96
Power supply unit: Auto-ranging electronic SMPS
Control and programming
Control channels (DMX): 2
Display: LCD display
Dimmer:0~100%
Physical / Installation
Weight: 11.6kg (17 lbs.)
IP rating: IP20
Material: Aluminum, steel, plastic
Mounting points: 12mm holes for G-Clamp
Minimum distance to combustible materials: 1.64ft. (0.5m)
Minimum distance to illuminated surfaces: 3.28ft. (1m)
Dynamic effects
Pan/Tilt movement: Manually adjustable
Thermal
Operating range: 14˚F to 113˚F (-10˚C to +45˚C)
Startup range: -13˚F to 113˚F (-25˚C to +45˚C)
Storage range: -40˚F to 140˚F (-40˚C to +60˚C)
Cooling: Passive
Humidity: ≤85%
Connections
AC power: Neutrik powerCon
DMX data input/output: Chassis 5-pin Neutrik XLR (in/out)
Certification and Safety

GTD-LYS300 (CW/WW) User Manual
11
EMC: EN 55103-1:2009, EN 55103-2:2009, EN 61000-3-2:2006+A2:2009, EN 61000-3-3:2013
Safety: EN 60598-2-17:1989/A2:1991
Photometric
LYS300 CW:
LYS300 WW:

GTD-LYS300 (CW/WW) User Manual
12
Cleaning and maintenance
It is required that the fixture should be kept clean and well maintained to ensure its reliability. Its lifespan mainly depends
on the working environment and proper operation. Should you have any questions, please consult a technical engineer of
GTD Lighting.
Notes
Damage resulted from dust, smoke, oil or improper use is not covered by warranty.
Warning
Disconnect the fixture from AC power, and let it cool down for at least 15 minutes before opening the housing. Make sure
to use a soft cloth to clean the optical components, and be careful, as the coating is easily scratched. Do not use any
organic solvent such as alcohol to clean the reflector mirror, dichroic color filters or housing of the fixture.
If the lens is cracked or otherwise damaged, replace it immediately.
If the LED lamp becomes damaged or deformed in any way it must be replaced.
If the light from the LED lamp appears dim, this normally indicates that it is reaching the end of its life span and
should be changed at once. Aged LED lamps run to the extremity of their life might explode.
If fixture does not function, check the fuse on the power socket of the fixture. Replace the fuse of the same
specification if it is blown.
The fixture is equipped with thermal-protection device that will switch off the LED lamp in case of overheating. If
this happens, please check that the fans are not blocked, and clean them if they are dirty. Check whether the fans
are operational. If not, call a qualified technician. Troubleshoot and correct the problem before switching on the
fixture again. Any maintenance work should only be carried out by qualified technicians.
Troubleshooting
Problem
Possible Cause
Suggested Correction
No response
after connected
to A/C power
Power switch not turned on.
Turn on power switch.
Take out the fuse and check if it is blown.
Locate the blown fuse. Remove the broken fuse. Insert a
replacement fuse of the correct amperage.
Abnormal A/C input (A/C power socket,
Replace AC power socket and power cables, and then adjust power

GTD-LYS300 (CW/WW) User Manual
13
Problem
Possible Cause
Suggested Correction
power cables, luminaire power socket).
socket for proper connection.
No DC voltage from switching power
supply.
Check if the switching power supply has DC voltage output. Replace
the switching power supply.
No response or
wrong response
to the
commands of
the control
system
DMX cables disconnected from fixture’s
DATA IN connector.
Connect DMX cable to the fixture’s DATA IN connector.
Open circuit or short circuit fault in the
DMX cables.
Replace DMX cables as required.
Wrong DMX address for the fixture in the
control system.
Ensure the address in “Run setting > Address Setting > Address”of
the fixture is consistent with the address in the control system.
Misuse in “Channel setting > Channel
Mode” of the fixture.
Choose the channel mode in “Channel setting > Channel Mode” of
the fixture as required by the user.
Malfunctioning of DMX cannon input
/output connectors. No input/output
voltage to the main control board of the
fixture.
Troubleshooting the DMX XLR signal plate of the fixture, replace the
main control board of the fixture.
LED lamp off
There is no signal output to the main
control board PWM.
Replace the main control board or repair.
No output to the drive board LED +/ LED-
or drive board over-current, check line
connector if contact bad.
Reconnect the terminal, replace the driver board
Normal end of LED lamp life, bad welding
or poor heat dispersion.
Repair or replace LED light source or replace the whole piece of
aluminum board, remove the cooling system failure.
Decreased
brightness,
uneven pattern
projections
LED lamp aging, check the service time of
LED light source, test LED drive board’s
current.
Replace the LED light source or adjust the drive board’s current.
Reduce LED’s brightness.
Excessive dusts or smudges on the effect
assembly, focus module and objective
lens.
Follow the instructions stated in this user manual to clean the effect
assembly, focus module and objective lens.
Damaged or deformed effect assembly,
focus module or objective lens.
Replace the damaged or deformed components.

GTD-LYS300 (CW/WW) User Manual
14
System wiring diagram
Spare parts list
Item
P/N
Qty
Notes
LYS300 Display
5809210088A
1
LYS300-101K10& 102N10 SDI0511B/display 511B-1
High power LED sets
5802016005A
1
LED LY-300W7575D30 Color Temperature: 3200±100K
White with thermistor 10K
LEDdriver 100B-1
5802030106A
1
LCR0100B
Signal caton board 2
5802910001A
1
SKL0002A
L
N
V+12
V+48
GND
GND
L
G
N
LED
LED Fan Switch power
fan
Focus
motor
DMX
Signal
Caron
Focusing
magnetic
susceptibility
LED Drive
Transfer Board High Power LED
Display
Power cable1.0mm2
Switch power
EDS360-4812P
GTD-LYS300
fuse Power

GTD-LYS300 (CW/WW) User Manual
15
Appendix 1

GTD-LYS300 (CW/WW) User Manual
16
Notes:
P/N: 1502011086A
Time: Aug21th, 2017