GUARDEON G-AIR4-250 User manual

Thanks for purchasing photoelectric quad beam detector, please read this user manual carefully
before installation.
Lock Nut
Vandtårnsvej 100, 2860 Søborg [phone] www.guardeon.dk

4. Attach beam to the base
Wire Hole
V
V
3 . Tamper switch (NC) is independent of the circuit,
anti-tamper trigger when cover is removed.
3 . Tamper switch (NC) is independent of the circuit,
anti-tamper trigger when cover is removed.
4. C relay (30VDC 1.0A max).
Vandtårnsvej 100, 2860 Søborg [phone] www.guardeon.dk

6
67 8
4 51 2
7 8
3
Heat
Preheat
3
Heat
Preheat
1 2
Beam Channel Beam Channel
4 5
Spare 6
An d o r Or
And
Or
6
And
Or
7 8
Beam Operation
All on
Up off
Down off
All off
7 8
All on
Up off
Down off
All off
Transmitter(TX)
Interruption Time And or Or Beam operation
Receiver(RX)
Indicators
Receiver POWER (Green)
Indicator turns on if TX and RX are powered.
Transmitter ALARM (Red)
ALARM indicator is always lighting if alarm activated; It will be off during arming.
DIP switches 1&2: Set beam frequency. TX and RX must be the same.
DIP switch 3: Set heater. PREHEAT is for test. Must set HEAT when it’s used.
DIP witches 4&5: Set interruption time.
DIP switch 6: Set “AND” or “OR” mode. “AND” means alarm activated if all 4 beams are blocked;
“OR” means alarm activated if either upper/down 2 beams are blocked.
DIP switches 7&8: Set Beam’s working mode.
ALL ON: 4 beams on.
UP OFF DOWN ON: disable upper 2 beams.
UP ON DOWN OFF: disable down 2 beams.
ALL OFF: disable all beams.
Notes: All set must be the same on both TX and RX except 4&5 (4&5 on TX is spare)
1.Set TX and RX same frequency by DIP switches 1&2.
2.Set “AND” and “UP ON DOWN OFF” mode, adjust up 2 beams
horizontally and vertically, it’s ok when LED is “99”.
3.Then at “UP OFF DOWN ON” mode, same set for down 2 beams
4.Then set “ALL ON” and alignment finished
5.Then do “walk test” to ensure it’ll activate alarm normally.
If failed, please re-do alignment. If alignment keeps failing,
please refer to troubleshooting.
Vandtårnsvej 100, 2860 Søborg [phone] www.guardeon.dk

12V-24V DC/AC
100mm 105mm
395mm
186.4mm
60mm
Mounting Hole
Auto Heating when it's ≤5℃ and stop heating when it's≥7℃
Possible cause
1. No voltage on power cable;
2. Broken circuit or short circuit;
3. Beyond specified voltage;
4. Power cable exceeds the
specified length
1. There is reflection or cross-talk
from other transmitters
2. Walk speed set too long
3. Alarm output cable is shorted or
damaged
1. Beam is out of alignment; optical
axis does not overlap
2. There are objects between TX
and RX
3. Frequency is incorrect
4. The cover is dirty or capped by
snow, frost and ice
5. TX is faulty or OFF
1. Bad wiring and fluctuant power
voltage
2. Randomly blocked, like birds,
paper or leaves
3. The beams base is unstable
4. Out of alignment
1. Change beam path or change
TX/RX frequency channel
2. Ensure 4 beams all blocked
3. Change walk-speed setting
4. Check receiver terminal and
output cable
1. Adjust optical axis
2. Check objects between TX and RX
3. Ensure the frequency of TX and RX
is the same
4. Clean cover or user heater
5. Check the voltage or wiring of
the TX
1. Check power, current and wiring
2. Change installation location
3. Strengthen installation base
4. Re-align
Symptom
Power on, but power
LED off
When beam is
blocked, the alarm
LED does not
indicate, nor does
the alarm relay switch
When beam is not
blocked, alarm LED
indicates activation
False alarm
Remedy
1. Check PSU, voltage, cables and
connectors
3 options ( interruption of all 4 beams or upper 2 beams or below 2 beams )
Vandtårnsvej 100, 2860 Søborg [phone] www.guardeon.dk