Gundermann VIDEOWALL LEDWALL Optimizer HQ P2 User manual

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
1
Manual
LEDWALL Optimizer HQ_P2
Valid for devices with the number:
#42705 LEDWALL Optimizer HQ_P2
without camera alignment system

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
2
Service for the customer
Adress Gundermann Mikroelektronik GmbH
Opelstr. 16
68789 St. Leon-Rot
Deutschland
Tel. [phone]
Fax [phone]
E-Mail [e-mail]
Opening hours Mo. - Fr. from 9:00 to 17:00
Notice
Gundermann Mikroelektronik GmbH maintains the right to change
hardware, packaging and all adjoining documentations without prior notice.
LEDWALL Optimizer HQ_P2 is a trademark of Gundermann
Mikroelektronik GmbH.
© 2010 Gundermann Mikroelektronik GmbH, All rights reserved.
All trademarks are property of the individual owner.

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
3
Precautions and conventions
In this manual following precautions and conventions are valid:
indicates notices, which disregard can lead to harm to health or
damages.
indicates important information and advice for the appropriate handling
of the system.
►indicates a necessary step of procedure.
inverse font indicates notations of programs, instructions or menu options.
„Quotation- indicates names of chapters and terms, which should be emphasized.
marks“
CE marking
This device in the delivered model is compliant to the Directive
2004/108/EG of the European Union, Directive on the approximation of
the laws of the Member States relating to electromagnetic compatibility
and the Directive 2006/95/EG Electrical equipment designed for use
within certain voltage limits (Low Voltage Directive) of the European
Parliament.
Disposing of electronic devices
This device is not supposed to be disposed in ordinary household
waste. This product is in compliance with the Directive 2002/96/EG of
the European Parliament and of the Council of the European Union on
WEEE (Waste Electrical and Electronic Equipment), as amended by
the Directive 27.Januar 2003/108/EC, where applicable.
Help preserve the environment! Ensure that this product is recycled at
the end of its life.
!
i

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
4
Table of Contents
1 Security
1.1 Security notice............................................................................................................5
1.2 Intended use ..............................................................................................................5
2 Technical description
2.1 Description of connections .........................................................................................6
2.2 Principal function........................................................................................................7
3 Technical data.................................................................................................................8
4 Installation and settings
4.1 Installation of the LEDWALL Optimizer HQ_P2 device...............................................9
4.2 Installation of the VCP-driver (optional)......................................................................9
4.3 Installation of the camera-diver (optional)...................................................................9
4.4 Installation of the LCS-program (optional)..................................................................9
4.5 Settings of the LCS-program (optional)......................................................................9
4.6 Execution of the camera alignment (optional).............................................................9
4.7 Pixelkoefficients (optional)..........................................................................................9
4.8 Remarks (optional).....................................................................................................9
5 Service...........................................................................................................................10
6 Scope of delivery...........................................................................................................11
7 Remarks.........................................................................................................................12

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
5
1 Security
1.1 Security notice
- This manual has to be kept with the device.
- If the device is passed to a third party, the manual has to be passed as
well.
- All persons working with this device have to strictly pay attention to the
manual.
- The device has to be connected with a three cord main cable with
grounding.
Transport
- The device has to be transported in the original packaging or another
suitable packaging to protect it sufficiently from shocks and concussions.
- The device has to be unpacked at the designated location.
Cleaning
- The device has to be turned off and all plugs have to be removed.
- Use no abrasive detergents, otherwise the finish might be affected.
- Pay attention that no liquids get into the housing.
- The surface of the housing has to be cleaned with a dry cloth. Is the device
extremely dirty use a mild detergent with a moistened wrung out cloth.
1.2 Intended use
The LEDWALL Optimizer HQ_P2 is a control gear which adjusts
LEDWALL systems which are controlled digitally (DVI/HDMI).
The device can be used for Indoor and Outdoor LEDWalls, whilst the
device has to stay Indoor.
!
!
!
i

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
6
2 Technical description
2.1 Description of connections
Description:
1 - Detachable 19-inch mounting bracket
2 - „Test“-button (Turn On/Off of pixel coefficients / colour generator)
3 - General information about the device
4 - Power connection
5 - HDMI/DVI-Input
6 - HDMI/DVI-Output
7 - „Service“-connection (only for technicians)
8 - USB-connection (to be used with the camera-alignment)
9 - Control-LEDs:
Red LED:
●Communication with LCS-program
●3-times flashing: error
Green/Blue LED:
●Slow flashing: device is turned on and HDMI/DVI signal is connected
●Fast flashing: device is turned on and HDMI/DVI signal is not connected
●No flashing: software-/hardware-error
Fig
. 2
.1
–
LEDWALL Optimizer HQ_P2 (
front
)
Fig
. 2.2
–
LEDWALL Optimizer HQ_P2 (
back
)
1
2
3
4
3
5
6 7 8 9

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
7
2 Technical description
2.2 Principle function
The LEDWALL Optimizer HQ_P2 device supports digital videosignals
(HDMI/DVI) with max. XGA-resolution (1024x768). An unscaled signal-line
has to exist at the LEDWall-system (e.g. between DVI receiver and
transmitter).
The LEDWALL Optimizer HQ_P2 device is connected between
videosource and videowall, that the transmitted picture signal will be
influenced that way, that after the camera alignment all LEDs are shining in
the same brightness and a homogenous picture will be presented.
Advices and steps whilst setting up the device:
►The LEDWALL Optimizer HQ_P2 device with presaved pixel
coefficients has to be integrated in a DVI-line (see Chapter: 4.1
„Installation of HQ_P2-device“).
►The function of the LEDWALL Optimizer HQ_P2 device can be
checked with the „Test“-button (Fig.: 2.1 Pos. 2). With a short push of
the button the pixel coefficients will be inactive, that the original
(uncorrected) signal will appear on the LEDWALL. Letting go of the
button the pixel coefficients are active again and the videosignal will be
changed accordingly.
►The LEDWALL Optimizer HQ_P2 device has an integrated colour
generator, that the individual basic colours (red, green, blue and white)
can be easily generated. Press the “Test”-Button (Fig.: 2.1 Pos. 2)
longer (approx. 2 seconds). If you press the button longer the colour
will change according above listing. If you press the button shortly
during a primary colour the picture will appear without pixel correction.
i

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
8
3 Technical data
Signal requirements
Supported digital signal………………..…………………….…
Maximum Resolution……………………………………………
Vertical synchronisation…………………………
Horizontal synchronisation………………………
Dimensions and weight
Width (with 19-inch mounting bracket)..…………..………………
Width (without 19-inch mounting bracket)…...…..…………………
Height…………………………….……………………………………….
Depth……..………….………………………………………………….
Weight……………………………………………………………………..
Power supply
Frequency……………………………………………………………
Supply voltage……………………………………………………...
Power consumption…………..…………………………………………
Internal fuse….…………..……………………………………………..
Environmental conditions
Operating temperature…….……………………………………………
Storage temperature………………………………………………….
Humidity………………….…
Emissions …………………………….…….…………………….………………….
HDMI, DVI
1024 x 768 Pixel
automatically detected
automatically detected
483,0 mm
433,0 mm
44,0 mm
225,0 mm
2,0 kg
47-63 Hz
90-255 VAC
20 Watt
2 A
0 bis +40°C
-20 bis +50°C
90% rel. humidity (not condensed)
CE

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
9
4 Installation and settings
4.1 Installation of the HQ_P2 device
During the installation of the LEDWALL Optimizer HQ_P2 device you have
to use the cables of the scope of delivery.
During the installation of the LEDWALL Optimizer HQ_P2 device notice the
following steps:
►HDMI/DVI-cable between the videosignals (e.g. PC with HDMI/DVI
output, HDMI/DVI receiver or similar) and the videoreceiver (Videowall,
HDMI/DVI-transmitter or similar) have to be removed.
►The LEDWALL Optimizer HQ_P2 device has to be connected at this
place with two DVI-HDMI adapter cables (resp. HDMI-HDMI cables).
►The LEDWALL Optimizer HQ_P2 device has to be connected with the
power cable to the 230VAC-mains system.
►The device can be mounted optionally with the 19-inch mounting
brackets in a 19-inch rack.
4.2 Installation of the VCP-driver (optional)
4.3 Installation of the camera-driver (optional)
4.4 Installation of the LCS-program (optional)
4.5 Settings of the LCS-program (optional)
4.6 Execution of the camera alignment (optional)
4.7 Pixel coefficients (optional)
4.8 Remarks (optional)
Optional functions are only used with the camera alignment system!
i
i

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
10
5 Service
In case of device failure notice the following steps:
►The device has to be turned off.
►All plugs have to be removed from the device.
►Videosignals (e.g. PC with HDMI/DVI-output, HDMI/DVI receiver or
similar) and Videoreceiver (Videowall, HDMI/DVI transmitter or similar)
have to be connected again with DVI-DVI resp. HDMI-HDMI cables.
►The brightness of the according Videowall has to be set back from
100% to approx. 70% (depending on the system).
►The company Gundermann Mikroelektronik GmbH has to be informed.
i

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
11
6 Scope of delivery
The original packaging has to be kept! The materials might have to be
used for a coming transport.
►Unpack all parts.
►Check the content of the packaging to visible transport damages.
►Check if the content of the packaging is according to the delivery note.
If the scope of delivery differs from the details of the delivery note the
company Gundermann Mikroelektronik GmbH has to be informed
immediately.
Standard scope of delivery
Following components are included in the Standard scope of delivery of the
LEDWALL Optimizer HQ_P2:
●1 x #42705 LEDWALL Optimizer HQ_P2
●1 x LE-NETZ-1,0 power cable
●2 x LE-DVI-HDMI2 HDMI-DVI-adapter cables
●1 x Manual
Optional scope of delivery
Following components can be purchased optionally:
●1 x Driver-CD
●1 x USB-cable 2.0 1m
●1 x USB-cable 2.0 3m
●1 x Camera with lens
●1 x tripod
●1 x Aluminium case
i

G:\HQ\HQ_P2\Dokumentation\Doku_HQ_P2_allg_ohne_KA_Englisch.doc
Gundermann VIDEOWALL 2010
12
7 Remarks