GWF MP-RCM-H200 User manual

GWF MessSysteme AG T [phone]
Obergrundstrasse 119 F [phone] Technical support:
6005 Lucerne, Switzerland [email protected], www.gwf.ch T [phone], [e-mail]
…………………………………………………………………………………………………………………………………………………………………………………………………………………………………........................................
Subject to modification, 13.06.2022 - BAeXXXXX
DRAFT
1. If you have ordered a GWFcoder® MP meter with a cable or
the IP68 (flood-proof) version, the cable is pre-assembled. In
this case, please continue with point 8.
2. With a screwdriver for recessed-head screws (size 0) stab the
seal in the hinged lid (Fig. 1) and loosen the screw below the
seal.
3. Remove hinge lid.
4. Connect the wires of the radio module (red, green, black) to
the screw binders (Fig. 2). The polarity of the connecting
wires (red and black) makes no difference. Pay particular
attention to the connection of the green stranded cable. The
green stranded cable must be attached to the middle
position using the screw binders supplied separately with
the installation kit.
5. Insert the cable into the left strain relief part.
6. Install the meter lid and hinge lid again with a screw.
Caution: Do not pinch cable.
7. Insert seal.
8. We recommend the use of Scotchlok connectors when
installing an RCM®-H200 radio module to a GWFcoder® MP
meter with a connected cable that can be extended to 20 m.
A 3 x 0,25 mm2 cable must be used for the cable extension
(only stranded cable, not wire).
9. Installation methods RCM®-H200 radio module.
a) Wall installation
Mark the position for the two holes and attach the wall
bracket using the supplied wall plugs and screws. Insert the
radio module until it engages on the mounted wall bracket
(Fig. 3).
b) Pipe installation
Use cable ties to install the wall bracket at the desired
position. Insert the radio module until it engages on the
mounted wall bracket (Fig. 3).
10. Carry out a test read-out.
User manual
GWFcoder® MP - RCM®-H200 (split radio module)
Installation for all meters types with GWFcoder® MP register with ECO interface
Note:
To achieve the best radio range it’s necessary to
install the radio module vertically (see fig. 3)

GWF MessSysteme AG T [phone]
Obergrundstrasse 119 F [phone] Technical support:
6005 Lucerne, Switzerland [email protected], www.gwf.ch T [phone], [e-mail]
…………………………………………………………………………………………………………………………………………………………………………………………………………………………………........................................
Subject to modification, 13.06.2022 - BAeXXXXX
DRAFT
For use in USA (FCC):
 Changes or modifications not expressly approved by the manufacturer could void the user’s
authority to operate the equipment.
 This device complies with Part 15 of the FCC rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must
accept any interference received, including interference that may cause undesired operation.
 This device must be installed to provide at least 20 cm separation from the human body at all
times.
 This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This equipment
generates uses and can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio communications.
Howev¬er, there is no guarantee that interference will not occur in a particular installation. If
this equipment does cause harmful interference to radio or television reception, which can
be determined by turning the equipment off and on, the user is encouraged to try to correct
the interference by one of the following measures: Reorient or relocate the receiving
antenna / Increase the separation between the equipment and receiver / Connect the
equipment into an outlet on a circuit different from that to which the receiver is connected /
Consult the dealer or an experienced radio/TV technician for help.
For use in Canada (IC):
 This device complies with Industry Canada licence-exempt RSS standard(s). Operation is
subject to the following two conditions: (1) This device may not interference, and (2) this
device must accept any interference, including interference that may cause undesired
operation of the device.
 This device must be installed to provide at least 20 cm separation from the human body at all
times.
 Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence. L'exploitation est autorisée aux deux conditions suivantes : (1) l'appareil
ne doit pas produire de brouillage, et (2) l'utilisateur de l'appareil doit accepter tout
brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le
fonctionnement.
 Cet appareil doit etre installe pour fournir au moins 20 cm de separation du corps humain en
tout temps.