11
11
111
11
111
11
1
44
44
444
44
444
44
444
44
4
CC
CC
C
44
44
4
11
11
1
ø12
DD
DD
D
11
11
1
11
11
144
44
4
1500
100
110
1600 1500
1050
Figure 5Figure 5
Figure 5Figure 5
Figure 5
Figure 6Figure 6
Figure 6Figure 6
Figure 6
66
66
6
55
55
5
44
44
4
55
55
566
66
6
77
77
777
77
777
77
777
77
7
60
80
40 40
90
I. Preparing the floor attachments (Fig.: 5):I. Preparing the floor attachments (Fig.: 5):
I. Preparing the floor attachments (Fig.: 5):I. Preparing the floor attachments (Fig.: 5):
I. Preparing the floor attachments (Fig.: 5):
1/1/
1/1/
1/ Mark the distances between bracket support frames (4)(4)
(4)(4)
(4) on the floor: 1500 mm (4.92 ft) at both ends, and 1600 mm (5.25
ft) in the center (intermediate brackets).
2/2/
2/2/
2/ On the floor, mark the position of attachment elements (2 parallel lines, spaced by 110 mm (0.36 ft)), 100 mm (0.33 ft)
apart from the wall, to which the standing support frames (4)(4)
(4)(4)
(4) will be secured.
BB
BB
BALLETALLET
ALLETALLET
ALLET BB
BB
BARSARS
ARSARS
ARS
WITHWITH
WITHWITH
WITH BB
BB
BRACKETSRACKETS
RACKETSRACKETS
RACKETS
ONON
ONON
ON
FLOORFLOOR
FLOORFLOOR
FLOOR SS
SS
STANDINGTANDING
TANDINGTANDING
TANDING SS
SS
SUPPORTUPPORT
UPPORTUPPORT
UPPORT FF
FF
FRAMESRAMES
RAMESRAMES
RAMES (R(R
(R(R
(REFEF
EFEF
EF.: 2220 +2215B).: 2220 +2215B)
.: 2220 +2215B).: 2220 +2215B)
.: 2220 +2215B)
II. Securing and installing the ballet bars on the floor (Fig.: 5, 6, 7 and 8)II. Securing and installing the ballet bars on the floor (Fig.: 5, 6, 7 and 8)
II. Securing and installing the ballet bars on the floor (Fig.: 5, 6, 7 and 8)II. Securing and installing the ballet bars on the floor (Fig.: 5, 6, 7 and 8)
II. Securing and installing the ballet bars on the floor (Fig.: 5, 6, 7 and 8) (2 individuals recommended)::
::
:
1/1/
1/1/
1/ Drill two ø12 mm (0.47 in), 90 mm (3.54 in) deep holes, spaced by 110 mm (0.36 ft), along the plot of each bracket support
frame (2)(2)
(2)(2)
(2) (see Fig. 6Fig. 6
Fig. 6Fig. 6
Fig. 6).
2/2/
2/2/
2/ Vacuum clean the dust.
3/3/
3/3/
3/ First position one bracket support frame (4)(4)
(4)(4)
(4) onto the plot, at one end.
4/4/
4/4/
4/ Install 2 washers (6)(6)
(6)(6)
(6). Hammer the expansion bolts (5)(5)
(5)(5)
(5) supplied, through both washers (6)(6)
(6)(6)
(6) and the bracket support frame (4)(4)
(4)(4)
(4)
plate.
5/5/
5/5/
5/ Moderately tighten the bolts (5)(5)
(5)(5)
(5).
6/6/
6/6/
6/ Slide one wooden bar (1)(1)
(1)(1)
(1) through the previously attached bracket support frame (7)(7)
(7)(7)
(7), and let the end protrude by 60 mm
(2.36 in) (Fig. 8Fig. 8
Fig. 8Fig. 8
Fig. 8).
7/7/
7/7/
7/ Slide the second support frame (4)(4)
(4)(4)
(4) at the end of the wooden bar (1)(1)
(1)(1)
(1) already in place: insert it by 40 mm (1.57 in) (approx.),
i.e. just in the center of the cylindrical section (see Fig. 7Fig. 7
Fig. 7Fig. 7
Fig. 7).
8/8/
8/8/
8/ Repeat operations 4/4/
4/4/
4/ and 5/5/
5/5/
5/ to install the second support frame (4)(4)
(4)(4)
(4).
9/9/
9/9/
9/ Pre-install a second wooden bar (1)(1)
(1)(1)
(1) onto the next support frame (1)(1)
(1)(1)
(1): insert it by 40 mm (1.57 in) (approx.).
10/10/
10/10/
10/ Position, then slide the assembly (1)(1)
(1)(1)
(1) through the previous support frame (4)(4)
(4)(4)
(4).
11/11/
11/11/
11/ Repeat operations 9/9/
9/9/
9/, and 10/10/
10/10/
10/, until the last support frame (4)(4)
(4)(4)
(4) is in place. Slide it over the last wooden bar (1)(1)
(1)(1)
(1) (the bar end
should protrude by 60 mm (2.36 in)), and secure it to the floor, using the screws (5)(5)
(5)(5)
(5) and (7)(7)
(7)(7)
(7).
12/12/
12/12/
12/ The wooden bars (1)(1)
(1)(1)
(1) are very slightly curved. For the assembly to be aligned with the wall (stand up in line), rotate each bar (1)(1)
(1)(1)
(1)
until the convex part points downward (or upward).
13/13/
13/13/
13/ Tighten the attachment elements (5)(5)
(5)(5)
(5) of the support frames (4)(4)
(4)(4)
(4) on the floor: tightening torque is 23 Nm (see Fig. 6Fig. 6
Fig. 6Fig. 6
Fig. 6).
14/14/
14/14/
14/ Secure the wooden bars (1)(1)
(1)(1)
(1) onto the support frames (4)(4)
(4)(4)
(4) from below: 1 at each end, and 2 intermediate (4)(4)
(4)(4)
(4) using the wood
screws (7)(7)
(7)(7)
(7) (see Fig. 7Fig. 7
Fig. 7Fig. 7
Fig. 7 and 88
88
8).
Figure 8 - End – Detail CFigure 8 - End – Detail C
Figure 8 - End – Detail CFigure 8 - End – Detail C
Figure 8 - End – Detail C
Figure 7 - Intermediate – Detail DFigure 7 - Intermediate – Detail D
Figure 7 - Intermediate – Detail DFigure 7 - Intermediate – Detail D
Figure 7 - Intermediate – Detail D
NM28F -NM28F -
NM28F -NM28F -
NM28F - Page 3Page 3
Page 3Page 3
Page 3
