Gymtech 50519 User manual

NOTE:
Please read all instructions
carefully before using this
product
Table of Contents
Safety Notice
Exploded diagram
Assembly Instruction
Parts List
Ordering Parts
Model
50519
Retain This
Manual for
Reference
OWNER'S
MANUAL
Boxing Stand
50519
Please contact HUNTER LEISURE AUSTRALIA Should any questions
arise at 1800-632-792.
Spare part Service: If you require service, please do not return the
Boxing stand to the store. Contact Hunter Leisure Australia on
1800-632-792.

TABLE OF CONTENTS
BEFORE YOU BEGIN....................................................................................……………… …1
IMPORTANT SAFETY NOTICES...................................................................……………… …2
HARDWARE PACK.....…...................................................................................................... ..3
ASSEMBLY INSTRUCTIONS.........................................................................……………… …4
EXPLODED DIAGRAM…………………………………………………………………………… ….9
PARTS LIST……………………………………………………………………………………… …10
ORDERING PARTS…………………………………………………………………………………..11
BEFORE YOU BEGIN
Thank you for selecting the 50519 Boxing Stand by Gym Tech. For your
safety and benefit, read this manual carefully before using the machine. As
a manufacturer, we are committed to provide you complete customer
satisfaction. If you have any questions, or find there are missing or
damaged parts, we guarantee you complete satisfaction through direct
assistance from our factory. To avoid unnecessary delays, please call our
TOLL-FREE customer service number. Our Customer Service Agents will
provide immediate assistance to you.
Toll-Free Customer Service Number
1-800-632-792
Mon. – Fri. 9 a.m. – 5 p.m. PST
1
IMPORTANT SAFETY NOTICE

PRECAUTIONS
This exercise machine is built for optimum safety. However, certain precautions apply
whenever you operate a piece of exercise equipment. Be sure to read the entire manual before
you assemble or operate your machine. In particular, note the following safety precautions:
1. Keep children and pets away from the machine at all times. DO NOT
leave children unattended in the same room with the machine.
2. Only one person at a time should use the machine.
3. If the user experiences dizziness, nausea, chest pain, or any other abnormal
symptoms, STOP the workout at once. CONSULT A PHYSICIAN
IMMEDIATELY.
4. Position the machine on a clear, leveled surface. DO NOT use the machine
near water or outdoors.
5. Keep hands away from all moving parts.
6. Always wear appropriate workout clothing when exercising. DO NOT wear
robes or other clothing that could become caught in the machine. Running
or aerobic shoes are also required when using the machine.
7. Use the machine only for its intended use as described in this manual. DO
NOT use attachments not recommended by the manufacturer.
8. Do not place any sharp object around the machine.
9. Disabled person should not use the machine without a qualified person or
physician in attendance.
10. Before using the machine to exercise, always do stretching exercises to
properly warm up.
11. Never operate the machine if the machine is not functioning properly.
12. A spotter is recommended during exercise.
CARE AND MAINTENANCE
1. Inspect and tighten all parts before using the machine.
2. The machine can be cleaned using a damp cloth and mild non-abrasive detergent.
DO NOT use solvents.
WARNING: BEFORE BEGINNING ANY EXERCISE PROGRAM, CONSULT YOUR
PHYSICIAN. THIS IS ESPECIALLY IMPORTANT FOR INDIVIDUALS OVER THE
AGE OF 35 OR PERSONS WITH PRE-EXISTING HEALTH PROBLEMS. READ
ALL INSTRUCTIONS BEFORE USING ANY FITNESS EQUIPMENT. HYPER
EXTENSION LIMITED. ASSUMES NO RESPONSIBILITY FOR PERSONAL INJURY
OR PROPERTY DAMAGE SUSTAINED BY OR THROUGH THE USE OF THIS
PRODUCT.
SAVE THESE INSTRUCTIONS.
2
HARDWARE PACK

3
ASSEMBLY INSTRUCTION
Tools Required Assembling the Machine: Two Adjustable Wrenches and Allen Wrenches
NOTE: It is strongly recommended two or more people assembling this machine to avoid
possible injury.
STEP 1 (See Diagram 1)
A.) Attach Mid Base Support (#2) to Rear Base Support (#1). Align the holes

and secure them with four M10×20 Allen Bolts (#15) and four Φ10 Washers (#16).
B.) Insert two Weight Plate Holders (#5) into the holes in Rear Base Support (#1). Secure each of
them with one M10×65 Allen Bolt (#17), two Φ10 Washer (#16) and M10 Aircraft Nut (#18).
DIAGRAM 1
4
STEP 2 (See Diagram 2)
A.) Attach Left Base Support and Right Base Support (#3, #4) to the Mid Base Support (#2).
Align the holes, and secure with one M10×70 Carriage Bolts (#20), one Φ10 Washer (#16)
one M10 Aircraft Nut(#18) and two M10×20 Allen Bolt (#15),one Φ10 Washer (#16) .
B.) Insert the Heavy Bag Support Frame (#5) into the Left Base Support(#3). Align the holes and
secure with one M10×65 Allen Bolt(#17), Φ10 Washer (#16) and one M10 Aircraft Nut(#18).
(Note: Do not fully tighten the bolts and nuts at this stage.)
DIAGRAM 2