Gyration AS00258 User manual

Gyration Ultra Cordless Optical Mouse
User Manual

Product Specifications
Spec Ultra Cordless Optical Mouse RF Receiver
System Require-
ments TFull functionality on Mac and IBM compatible PCs running
Windows 2000, ME, XP or higher
TAvailable USB port
TCD ROM drive (for GyroTools installation)
TMicrosoft or Mac compatible mouse driver
Size 4.8”L x 2.0”W x 1.8”H (12.2cm x 5.1cm x
4.5cm) 5”L x 4”W x 2”H (13cm x 10cm x
5cm)
Weight 5.3 oz (150g) with battery pack 4 ounces (124g)
Operating
Range Consumer model - Up to 25 feet (7.6m) typical with no line-of-sight requirement
Professional model - Up to 100 feet
(30.5m) typical with no line-of-sight
requirement
N/A
Radio 49 MHz (U.S.) with 8 channels and 65,000
security addresses N/A
Batteries TNiMH battery pack
T3 AAA batteries (AAA battery clip
included with professional model
only)
N/A
Connector N/A USB with 5’ (1.5m)
cable
Operating Temp +10 to 40 C (+50 to +104 F)
Storage Temp -30 to +70 C (-86 to +158 F)

1
Gyration Ultra Cordless Optical Mouse
Identifying the Parts
Included with your mouse are the following components:
Ultra mouse - Consumer: mouse handset, charging station, RF receiver,
NiMH battery pack, AC adapter
Ultra mouse - Professional: mouse handset, charging station, RF receiver,
2 NiMH battery packs, inline charger, AAA battery clip, GyroTools CD, AC
adapter
Installing and Charging the Batteries
The Ultra mouse comes with a NiMH battery pack already installed but you
will need to remove the plastic insulator tab located inside the battery com-

2
partment. This clear plastic tab prevents the battery from discharging until
you are ready to use your mouse.
1. Press release button on the end of the mouse and lift battery pack
off.
2. Remove and discard plastic tab.
3. Replace battery pack by snapping into place.
Important! Your mouse must be charged for 8 hours prior to first use. To
charge your mouse:
1. Be sure that the NiMH battery pack is firmly in place.
2. Connect power adapter to charging cradle and plug into AC power
source.
3. Place mouse handset into charging cradle. LED on cradle will light
solid. LED indicator on mouse will flash slowly while batteries are
charging and maintain a steady glow when fully charged. (You may
remove the mouse from the charging cradle at anytime -- you do
not need to wait for the LED to stop flashing.)
Note: When battery reaches 20% of a full charge the LED indicator will blink intermit-
tently when transmitting data. To optimize the performance of your NiMH battery, it is
best to recharge after every use.
The NiMH battery pack can also be charged in a remote location using an in-
line charger (included with the Ultra mouse professional model and available
for purchase as add-on accessory):
1. Press release button on the end of the mouse and lift battery pack
off.
2. Connect power adapter to inline charger and plug into AC power
source.
3. Place battery pack into charger cradle to begin charging. LED indi-
cator on cradle will light solid.
A standard alkaline battery clip may also be used with your mouse (included
with the Ultra mouse professional model and available for purchase as add-
on accessory):

3
1. Insert 3 AAA batteries into battery clip.
2. Attach battery clip to mouse by snapping into place.
Setting Up and Synchronizing Ultra Mouse and the
Receiver:
1. Make sure the mouse is fully charged.
2. Power on your computer and connect the Receiver’s USB cable into
an available USB port on your computer. Follow standard USB
device installation screens.
3. Press and hold the LEARN button on the Receiver for 2 seconds. The
STATUS light will blink slowly, indicating that the receiver is in
“Learn Mode.”
4. Press the TEACH button located on bottom of the mouse handset.
The status light on the Receiver will blink rapidly for 4 seconds, then
will blink slowly. Push the TEACH button on any additional devices
(i.e. keyboard or 2nd mouse) at this time.
5. OPTIONAL: To exit “Learn Mode,” press the LEARN button on the
Receiver for 2 seconds. Otherwise, after five minutes, Learn Mode
will automatically time out.
If more than one Gyration device is being installed on the system, place the
Receiver into Learn Mode (step 3 above) only once, then “Teach” each device
before exiting Learn Mode. Do not push the Learn button on the receiver for
each device to be added. (Also see “Installing 3 or More Devices” on page 9.)
When the Receiver is put into Learn Mode, it erases its memory of learned
devices and looks for new devices. Therefore, when adding a new device to a
system it is necessary to put the Receiver into Learn Mode then Teach all
devices that will be used on the system.
Note: After the Teach/Learn sequence is performed, the Receiver and the device will
remain synchronized after powering down and changing channels. It is only necessary
to perform the Teach/Learn sequence when setting a device up for the first time or
when adding additional devices to the system.

4
Determining Which Channel Ultra Mouse is Using
The Ultra mouse has eight individual channels available to it. To determine
which channel a device is currently using:
1. Press and quickly release the CHANNEL button on the bottom of the
mouse handset. Count the number of times the red LED on the bot-
tom of the handset or the green LED on the top of the handset
flashes. The number of flashes indicates the channel the handset is
using.
Changing the Channel Ultra Mouse is Using
When two devices are being used in the same proximity, each device should
be set to operate on a unique channel. For best reception, space the chan-
nels apart by one or more channels.
To change the channel:
1. Press and hold the CHANNEL button on the bottom of the mouse
handset for 2 seconds. When you release the button, the mouse will
change to the next channel and the red LED on the bottom of the
handset and the green LED on the top of the handset will flash. The
number of flashes indicates the new channel the handset is using.
If a Teach/Learn sequence has already been performed, it will not be
necessary to re-synchronize the devices after a channel change.
Note: If the mouse’s channel is changed when the computer is powered down or the
receiver is not connected, the devices will become unsynchronized. When the system is
running, click and release the channel button as described above to initiate a “channel
confirm” operation. The mouse broadcasts a message across all eight channels that
informs the receiver what channel it is currently operating on. The receiver then
automatically restores synchronization.
Tip: If you are installing three or more devices on a single receiver, see “Installing 3 or
More Devices” on page 9.
Using Ultra Mouse on the Desktop
The Ultra mouse provides great flexibility in how you control your computer

5
and its optical sensor allows for precise tracking on virtually any surface (for
optimal performance, avoid highly reflective glass or mirrored surfaces). To
use on the desktop:
1. Set up and synchronize the mouse with the Receiver (see page 3).
2. Remove the fully charged mouse from the charging cradle and place
it on a flat surface. The LED light on the receiver base will flicker
rapidly when communicating with the mouse handset.
3. Use the mouse like a standard desktop mouse.
In addition to its optical sensor, Ultra mouse features an advanced reflective
sensor that detects when the mouse is being lifted off the desktop. To con-
serve battery life, this sensor powers on the Gyro and shuts down the optical
sensor each time the mouse is picked up.
The Ultra mouse uses standard Windows and Mac mouse drivers. Cursor
tracking speeds, mouse double-click speeds, and other options can be cus-
tomized using the Mouse Control Panel under Windows 98, 2000, ME, XP or
Mac OS 8 and above (see operating system documentation for further infor-
mation about customizing mouse properties).
Using Ultra Mouse in the Air
The Ultra mouse has no line-of-sight
requirements so it’s not necessary to point
the device at the computer, receiver or
monitor. Find a comfortable, relaxed
position and move the cursor with easy
wrist movements.
1. Set up and synchronize the mouse
with the Receiver (see page 3).
2. Hold the mouse in a comfortable,
relaxed position with your index finger on the ACTIVATION TRIG-
GER and your thumb at the base of the scroll wheel (see illustra-
tion).
3. Press and hold the ACTIVATION TRIGGER with your index finger.

6
While holding the ACTIVATION TRIGGER, flex your wrist up, down,
sideways, in a manner similar to using a flashlight. The mouse cur-
sor tracks the motions of your hand.
4. Use your thumb to press the left/right mouse buttons or to operate
the scroll wheel.
5. Double-click the ACTIVATION TRIGGER to keep the cursor continu-
ously active. To stop the cursor, click the ACTIVATION TRIGGER
once.
Powering Off Ultra Mouse
To power off the Ultra mouse:
1. Simultaneously press and release the CHANNEL button and TEACH
button on the bottom of the unit. The mouse will immediately enter
deep sleep mode and will be unresponsive to button clicks. The unit
will confirm it is powering off by flashing its LED three times.
2. Repeat this sequence to power the unit back on. The unit will
confirm it is powering on by flashing its LED for 1 second.
Note: It may be necessary to power off the unit when traveling on commercial airlines
due to FCC regulations regarding radio-emitting devices.
Fine-tuning Cursor Control
The Ultra mouse uses your standard Windows mouse driver. Any settings
that are available to a standard desktop mouse are also available to Ultra
mouse. Multiple factors will determine how you adjust your mouse to suit
your preference including screen resolution, mouse driver version and
overall personal preference. While becoming familiar with your mouse and
getting a feel for the GyroPoint method of cursor control, Gyration
recommends adjusting your mouse driver to the following settings:
TPointer Speed – Average. Some new users prefer this setting to be
slightly slower than average. Advanced users will increase the
speed so that less wrist movement gives them more screen

7
coverage with the cursor.
TAcceleration – Low or Off.
Ultra Mouse Troubleshooting Tips
Symptom Reason Solution
Mouse LED comes on
when activate button
is pressed, but
receiver is
unresponsive
Mouse and Receiver
not Synchronized Perform a Teach/Learn sequence. (See “Getting Started” on page 1.)
Cursor is visible but
shows no movement Gyro not activated Squeeze or double-click trigger on
bottom of mouse.
Cursor movement is
choppy or erratic Radio interference 1. Change the device’s channel setting. (See “Changing the
Channel Ultra Mouse is Using”
on page 4.)
2. Move receiver away from
other electronic devices (e.g.
monitor, speakers, radio,
etc.).
When pressing the
activate button, the
LED on the mouse is
flashing
Batteries are low
Replace or recharge batteries (see
page 1)
When pressing the
activation trigger, the
LED on the mouse is
off
Batteries are dead
Cursor moves too fast
or too slow Speed or acceleration not set
properly
Change the cursor tracking speed
in the mouse control panel (see OS
documentation for details).

8
Gyration RF Receiver
Learn Button
Pressing the LEARN button for 2 seconds puts the receiver into “Learn Mode”
allowing you to synchronize one or more devices with the receiver. After
devices have been synchronized, pressing the LEARN button again for 2
seconds takes the receiver out of Learn mode. If the receiver is not manually
taken out of Learn Mode, it will automatically return to Normal Mode after
five minutes.
Status LED
The Status LED displays useful information about modes of operation and the
connection between receiver and transmitter(s).
TThe Status LED remains off when the receiver is operating in
“Normal Mode” and no devices are transmitting.

9
TThe Status LED flickers rapidly when the receiver is operating in
“Normal Mode” and a synchronized device is transmitting. If there is
radio interference, the flickering light will be inconsistent.
TThe Status LED blinks slowly (1 blink per second) when the receiver
is in Learn Mode and is awaiting a Teach instruction from a device.
TThe Status LED blinks rapidly for a 4-second burst when it is in
Learn Mode and processing a Teach instruction and synchronizing
the receiver with the device.
Keyboard Status LEDs
The Keyboard Status LEDs will indicate whether your computer has the Num
Lock, Caps Lock and/or Scroll Lock features activated.
Conflict LED
If an unrecognized Gyration device is attempting to operate on the same
channel as a device that has been synchronized, the red “Conflict” LED on
the receiver will flicker and input control may be intermittent.
The Conflict Light will only detect interference from another Gyration RF
device (i.e. not cordless phones, personal radios, etc.).
Installing 3 or More Devices
The Receiver can be taught to recognize up to eight devices (mice, remotes,
keyboards, etc.) on a system, but only two of those devices may be used
simultaneously. When setting up a system with a single receiver and 3 or
more devices, the following guidelines must be followed:
TSelect two channels that are free of outside interference and install
all devices on either of those two channels. When possible, it is
recommended that the two chosen channels be separated by at
least one unused channel.
TAny of the devices installed on one channel may be used

10
simultaneously with any of the devices on the other channel. Two
devices that share a channel may not be used simultaneously.
When installing the devices try to determine which devices will be
used simultaneously and set them on opposite channels.
The following example describes a single-receiver system with two mice and
a keyboard that requires one mouse to be used by a presenter for cursor
control while another presenter inputs data on the keyboard. Mouse #1 is set
to channel 3 and the keyboard and mouse #2 are set to channel 5. With this
configuration, mouse #1 and the keyboard can be used simultaneously, but
mouse #2 and the keyboard cannot.
Note: Gyration carries both a consumer and professional line of RF products. Please
note that a low-power consumer device (i.e. Ultra mouse with 25-ft. range) should not
be used simultaneously with a high-power professional device (i.e. RF Keyboard with
100-ft. range). One or both devices may not work properly if data is being transmitted
by the two units at the same time. For optimal performance, it is recommended that
you alternate usage between the devices.

11
REGULATORY INFORMATION
ATTENTION! THIS DEVICE EMITS RADIO FREQUENCIES AND HAS NOT BEEN
CERTIFIED BY THE FAA FOR USE ONBOARD AIRCRAFT. DO NOT USE THIS
DEVICE AT ANY TIME ONBOARD CIVIL AIRCRAFT. TO MINIMIZE THE
POSSIBILITY OF INTERFERENCE, POWER OFF MOUSE TO ENSURE THAT IT
REMAINS OFF DURING FLIGHT.
FCC Statement
The Ultra Cordless Optical Mouse and RF Receiver have been tested and
found to comply with the limits for a Class B digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installation. This
equipment generates, uses and radiates radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does
cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to
try to correct the interference by one or more of the following measures:
1. Reorient or relocate the receiving antenna (television, radio, etc.).
2. Increase the separation between the equipment and receiver.
3. Connect the equipment to an outlet on a circuit different from that
to which the receiver is connected.
4. Consult the dealer or an experienced radio/TV technician for
additional help.
Caution: Changes or modifications not expressly approved by the party
responsible for compliance could void the user's authority to operate the
equipment. Contact Gyration, Inc., 12930 Saratoga Avenue, Bldg. C,
Saratoga CA 95070. Technical Support phone: [phone]. These devices
comply with Part 15 of the FCC Rules.
Operation is subject to the following two conditions:

12
1. these devices may not cause harmful interference, and
2. these devices must accept any interference received, including
interference that may cause undesired operation.
The mouse operates in the frequency band of 49.82 to 49.9 MHz with RF
output power of less than 30 MicroWatts EIRP (Effective Isotropic Radiated
Power).
Warning: Using these products in any way other than as described in this
manual or altering the antenna in any way may violate FCC rules.
FCC ID: JJ4-AS00245 (Ultra Cordless Optical Mouse)
Receiver: AS00216-001
Canadian Radio Interference Regulations
This Class B digital apparatus meets all requirements of the Canadian
Interference Causing Equipment Regulations.
Cet appareil numérique de la classe B respecte toutes les exigences du
Règelement sur le matériel brouil-leur du Canada.

13
Contacting Gyration
If you have any questions on your new Gyration product, please use any of
the phone/FAX numbers or addresses below:
Main Office
Gyration, Inc.
12930 Saratoga Avenue, Bldg. C
Saratoga, CA 95070
USA
Phone: [phone]
Fax: [phone]
Sales
Phone: [phone] (Toll-free in US and Canada)
Fax: [phone]
E-mail: [e-mail]
Technical Support
Phone: [phone]
E-mail: [e-mail]
World Wide Web
www.gyration.com
Warranty Information
Gyration products come with a one-year hardware warranty. Gyration, Inc.,
(Gyration) warrants products against defects in material and workmanship
for a period of one year from the date of purchase from Gyration or an
authorized Gyration agent. This warranty applies only to the original
purchaser and is not transferable. This warranty does not cover any
incompatibilities due to the user's computer, hardware, software or any
other related system configuration in which the product interfaces. Proof of
purchase will be required before any warranty consideration by Gyration
occurs. This warranty does not cover any damage caused by negligence,
non-authorized modifications, or parts installed without prior written

14
permission from Gyration. This warranty does not apply if the product has
been damaged by accident, abuse, misuse, or misapplication, nor as a result
of service to the product by anyone other than by Gyration.
Gyration is not responsible for any lost profits, lost savings or other
incidental or consequential damages arising out of the use of, or
inability to use, this product. This includes damage to property and,
to the extent permitted by law, damages for personal injury. This
warranty is in lieu of all other warranties including implied
warranties of merchantability and fitness for a particular purpose.
Some states do not allow limitation of implied warranties, or exclusion or
limitation of incidental or consequential damages, so the above limitations
may not apply to you. This warranty gives you specific legal rights. You may
have other rights which may vary from state to state. This warranty applies
only to these products, and is governed by the laws of the State of California.

Gyration Ultra Cordless Optical Mouse
User Manual
Gyration, Inc.
12930 Saratoga Avenue, Bldg. C
Saratoga, CA 95070
1.800.316.5432
www.gyration.com