4. BOTTLE LENGTH HEIGHT ADJUSTMENT
OPERATION
1.
2.
Do not force the lever down or it may be difficult to adjust in the future.
4. If, after adjusting the top clamp, the center guide interferes with the release cable, adjust the center guide
down to the desired height. Once the height has been established, tighten the screws to lock in place.
CAUTION
The installer is liable for SCBA bracket adjustment. If locking nut is not secured onto screw,
the stop could come loose and clamping assembly can slide out of channel.
Figure 6
4
ADJUSTMENT LEVER
CENTER GUIDE
OPTIONAL ADJUSTMENTS
SHROUD POSITION
back shroud forward or rearward to better accommodate
SCBA cylinder sizes. The shroud for an ABTS (All Belts
To Seat) seat differs from that of a non-ABTS seat.
The shroud is usually assembled in the most compact
(forward) position and may be adjusted rearward for
larger diameter SCBAs. See Figure 12.
1. To adjust, remove the two mounting screws
on either side of the shroud.
2. Reposition shroud as desired.
Replace screws.
SECUREALL®POSITION
of the shroud for mounting the SecureALL®offset right or
left to improve ingress/egress of the SCBA. To adjust, use
1
2
SecureALL®to shroud. Move SecureALL®right or left and
replace the screws. See Figure 11.
3
⁄4" (19mm) LATERAL
ADJUSTMENT IN
EITHER DIRECTION
SHROUD DEPTH ADJUSTMENT
FOR ABTS SEATS
3
⁄16" (4.5mm) HEX KEY WRENCH
AND 7
⁄16" (11mm) HEX WRENCH
SHROUD DEPTH ADJUSTMENT
FOR NON-ABTS SEATS
#3 PHILLIPS SCREWDRIVER
(SCREW HEADS CONCEALED
BY BLACK PLASTIC CAPS)
5. CABLE ATTACHMENT AND ADJUSTMENT
The release cable is routed up through the opening in the cylinder support and center guide and is
attached to the latch bracket by two nuts tightened around latch bracket. See Figure 7.
1. Screw and nut attaching cable to latch should spin freely, but screw on thread should fully engage nylon
insert in nut. See Figure 7.
2.
2a.
2b. For optimum release handle position, adjust the cable length so the latch releases when the handle
is near the top 80% of range of motion. See Figure 8.
Figure 7
Figure 8
LATCH BRACKET
CABLE ATTACHMENT
NUT AND SCREW
NUT A
NUT B
Figure 11
Figure 12
RELEASE HANDLE KITS
8920-034:
8902-035:
Note: Release handles for flip up cushions require complete new cushion.
ADDITIONAL SecureALL®KITS
8920-035: SecureALL®Bracket without release handle or cushion
8920-043: SecureALL®Bracket with release handle, no cushion
8920-037: SecureALL®wall mount
SECUREALL SERVICE KITS
8902-036
SEE BOTTLE SPECIFIC SERVICE KITS
FOR ADDITIONAL OPTIONS
8902-052
8902-039
CENTER GUIDE
8902-131
8920-068
SEE BOTTLE SPECIFIC SERVICE
KITS FOR ADDITIONAL OPTIONS
Figure 18
PIVOT ARM & PIN
8902-112
W/O CLAMP
8902-111
8920-033
SEE KIT LIST BELOW
REST STOP
8900-024
Figure 19
WARNING
The installer is liable for SCBA holder mounting. Failure to properly tighten fasteners could result in
serious injury or death due to SCBA bracket coming loose from the seat.
BOTTLE SPECIFIC SERVICE KITS
The SecureALL®
MSA G1 Valve uses 8920-079 Valve Cup Kit
Diamond-Shaped Valve uses 8920-080 Valve Cup Kit
MSA M7 Valve uses 8920-076 Valve Cup Kit
High Pressure Composite Cylinder Kit 8902-090
Figure 14
Figure 16
USE WITH THE FOLLOWING SCOTT CYLINDERS:
8902-065 Long Clamp Kit
Figure 17
OPERATING INSTRUCTIONS
STORING SCBA
Place SCBA valve into cup with valve against front edge of cup.
Place upper end of SCBA cylinder against the pivot arm locking
plate and push to engage latch. See Figure 9.
REMOVING SCBA
Pull up on the release handle in the front center of the seat
cushion to open the clamp. Remove SCBA. See Figure 10.
TROUBLESHOOTING
If the latch doesn’t engage:
1. Ensure the valve is sitting in the valve cup and not on the edge.
2.
Figure 9
CAUTION
SecureALL®clamping assembly captures top of SCBA
cylinder and has a pinch point. Use caution and avoid
potential pinch points when operating clamping assembly.
Figure 10
NOTICE: For additional assistance contact your OEM, dealer OR
H.O. BOSTROM COMPANY, INC.
818 PROGRESS AVE, WAUKESHA, WI 53186
WWW.HOBOSTROM.COM
Wall Mount
8920-037
®
