H3C ANT-2503C-M6 User manual

i
Contents
H3C ANT-2503C-M6 ceiling-mount antenna installation guide ·············································································· 1
Technical specifications····················································································································································1
Safety precautions·····························································································································································4
Installation guidelines ·······················································································································································4
Choosing a mounting location ········································································································································4
Mounting the antenna ······················································································································································4
Tools and accessories required ······························································································································4
Mounting the antenna on a ceiling ························································································································5
Recommended cable················································································································································8

Manual Version:5PW100-20120627
1
H3C ANT-2503C-M6 ceiling-mount antenna
installation guide
Technical specifications
The ANT-2503C-M6 antenna is designed for use in indoor environments. It is connected to the 2.4-GHz
or 5-GHz antenna port on an H3C indoor AP through an RPSMA-J connector.
Figure 1 Antenna view
Table 1 Technical specifications
Antenna type ANT-2503C-M6
Operating frequency range 2400 MHz to 2500 MHz 5150 MHz to 5850 MHz
Bandwidth 100 MHz 700 MHz
Peak gain 2.5 dBi 4.5 dBi
Voltage standing wave ratio (VSWR) ≤1.5 ≤2.5
Impedance 50 Ω
Polarization type Vertical
Max. power 50 W
Connector RPSMA-J
Dimensions 245 × 142 × 36 mm (9.65 × 5.59 × 1.42 in)
Weight 0.74 kg (1.63 lb)
Operating temperature –40°C to +60°C (–40°F to +140°F)
Installation Ceiling mounting
Figure 2 through Figure 5 show the horizontal and vertical radiation patterns.

Manual Version:5PW100-20120627
2
Figure 2 2.4-GHz horizontal pattern
Figure 3 2.4-GHz vertical pattern

Manual Version:5PW100-20120627
3
Figure 4 5-GHz horizontal pattern
Figure 5 5-GHz vertical pattern

Manual Version:5PW100-20120627
4
Safety precautions
W
ARNING!
•Installing antennas is dangerous. For your safety, follow the installation directions.
•Keep the antenna away from power source, street lamps, distribution box, or other places that may
cause electrical shock.
•Do not touch any power lines for your safety.
•Keep safety in mind when you select your installation site. Keep the antenna away from electric
power lines and other lines.
•Do not work alone when you install the antenna.
•If you need to raise the mast, work with other people to avoid bodily injury.
•Do not use a metal ladder. Do not work on a wet or windy day. Dress properly, for example, shoes
with rubber soles. Wear rubber gloves.
•If the antenna, antenna cable, or any other installation accessory drops, get away from it to avoid
bodily injury.
•If an accident, for example, electrical shock, occurs with the power lines, immediately call for
qualified emergency help.
Installation guidelines
The ANT-2503C-M6 is designed to be mounted indoors on a ceiling to maximize its omnidirectional
propagation characteristics. Install multiple antennas where necessary because doors, windows, and
walls degrade signal quality. Keep the antenna away from metal obstructions and wire mesh.
Choosing a mounting location
The ANT-2503C-M6 is a MIMO-omnidirectional antenna typically mounted indoors on the ceiling. Keep
the antenna away from metal obstructions such as heating and air-conditioning ducts. Typically, the
higher an antenna is above the ground, the better it performs. If possible, use a cable as short as possible
to connect the antenna and AP.
Mounting the antenna
You can mount the ANT-2503C-M6 antenna on a ceiling by using bolts or a T-rail. The installation
accessories are provided (installation tools are user supplied). If you intend to mount your antenna on
another surface, you must provide the appropriate installation accessories.
Tools and accessories required
•Accessories provided with the antenna for bolt-mounting:
{One paper mounting template
{Two M6 bolts
{Two M6 hex nuts
{Two 6 mm (0.24 in) diameter flat washers

Manual Version:5PW100-20120627
5
{Two 6 mm (0.24 in) diameter spring washers
•Accessories provided with the antenna for T-rail mounting:
{One paper mounting template
{Three clips fastened on the antenna
{Three mount clamps
•User-supplied tools:
{One adjustable wrench
{One electric drill and associated drill bits
Mounting the antenna on a ceiling
The ANT-2503C-M6 antenna can be mounted on a ceiling by bolts or a T-rail.
Bolt mounting
To mount the antenna by using bolts:
1. Use the paper mounting template to mark the holes on the ceiling where you want to mount the
antenna and then drill eight holes in the ceiling. See Figure 6.
Figure 6 Paper mounting template
2. Thread the two M6 bolts into the screw holes at the antenna base (see Figure 7) and fasten them.

Manual Version:5PW100-20120627
6
Figure 7 Mounting the M6 bolts
(1) Antenna (2) Cable (3) M6 bolt
3. Thread the antenna cable and M6 bolts through the holes you drilled in step 1 until the base of the
antenna is flush with the ceiling. Thread the M6 hex nut, flat washer, and spring washer (callout 1
in Figure 8) through the M6 bolt and fasten them until the antenna is secured in place.
4. Fasten the other M6 bolt with the other set of M6 hex nut, flat washer, and spring washer.
Figure 8 Mounting the antenna
(1) M6 hex nut/flat washer/sprin
g
washer (2) Cable (3) Ceilin
g
T-rail mounting
To mount the antenna by using a T-rail:
1. Use the paper mounting template to mark the holes on the ceiling where you want to mount the
antenna and then drill six holes in the ceiling. See Figure 9.
123

Manual Version:5PW100-20120627
7
Figure 9 Paper mounting template
2. Fasten the mount clamps to the T-rail as shown in Figure 10.
Figure 10 Fastening mount clamps to the T-rail
(1) T-rail (2) Mount clamp
3. Thread the antenna cable through the holes you drilled in step 1 until the base of the antenna is
flush with the ceiling.
4. Fasten the clips to the mount clamps until the antenna is secured in place. See Figure 11.
Figure 11 Fastening the clips
(1) Cable (2) Clip

Manual Version:5PW100-20120627
8
Recommended cable
H3C recommends that you use a high-quality, low-loss cable with the antenna. Coaxial cable loses
efficiency as the frequency increases, causing signal loss. Keep the cable as short as possible because
cable length also causes signal loss (the longer the run, the greater the loss).