H3C MPU-LSQM2SUPA0 User manual

Manual version: 6PW103-20180115 BOM: 3123A1J8
i
MPU—LSQM2SUPA0
1 Card identifier
The card identifier LSQM2SUPA0 is in the upper right corner of the front panel.
2 Specifications
Table 1 Card specifications
Item Specification
Flash 2 GB
BootROM 8 MB
NVRAM 1 MB
SDRAM (DDR3) 2 GB
Card size (H × W × D) 45 × 199 × 355 mm (1.77 × 7.83 × 13.98 in)
Power consumption 9W to 18W
Interfaces
•1 console port
•1 USB console port
•2 network management ports: 1 RJ-45 ports and 1 SFP fiber ports
•1 primary USB port
Transmission rate
•Console port: 9600 bps to 115200 bps (default: 9600 bps)
•USB console port: ≤115200 bps (default: 9600 bps)
•network management ports ( RJ-45 ): 10/100/1000 Mbps, half/full
duplex
•network management ports (SFP ): 1000 Mbps
Transmission medium and max
transmission distance
•Console port: 15 m (49.21 ft) over asynchronous EIA/TIA-232
cables
•USB console port: 10 m (32.81 ft) over USB-AB cables
•network management ports ( RJ-45 ): 100 m (328.08 ft) over
Category 5 or higher twisted pair cables
•network management ports (SFP ): see Table 3
Compatible device models S7503X/S7503X-PoE
Software version Version 7536 and later
NOTE:
H3C recommends not using a USB extender cable to connect the USB port.
The 10/100/1000BASE-T copper port uses an RJ-45 connector.

Manual version: 6PW103-20180115 BOM: 3123A1J8
ii
Figure 1 RJ-45 connector
Table 2 RJ-45 GE connector pinout
Pin 10BASE-T/100BASE-TX/1000BASE-T
Signal Function
1 MX_0+ Transmits and receives data.
2 MX_0- Transmits and receives data.
3 MX_1+ Transmits and receives data.
4 MX_2+ Transmits and receives data.
5 MX_2- Transmits and receives data.
6 MX_1- Transmits and receives data.
7 MX_3+ Transmits and receives data.
8 MX_3- Transmits and receives data.
Table 3 describes the SFP transceiver modules available for the SFP and SFP+ ports on the card.
Table 3 GE SFP transceiver modules available for the SFP and SFP+ ports
GE SFP transceiver
module Central wavelength Connector type Cable specifications
Maximum
transmission
distance
SFP-GE-SX-MM850-A 850 nm LC
50/125 µm multi-mode
optical fiber (MMF) 550 m (0.34 miles)
62.5/125 µm MMF 275 m (0.17 miles)
SFP-GE-SX-MM850-D 850 nm LC
50/125 µm MMF 550 m (0.34 miles)
62.5/125 µm MMF 275 m (0.17 miles)
SFP-GE-LX-SM1310-A 1310 nm LC
9/125 µm single-mode
optical fiber (SMF) 10 km (6.21 miles)
50/125 µm MMF 550 m (1804.46 ft)
62.5/125 µm MMF 550 m (1804.46 ft)
SFP-GE-LX-SM1310-D 1310 nm LC
9/125 µm SMF 10 km (6.21 miles)
50/125 µm MMF 550 m (1804.46 ft)
62.5/125 µm MMF 550 m (1804.46 ft)
SFP-GE-LH40-SM1310 1310 nm LC 9/125 µm SMF 40 km (24.86 miles)
SFP-GE-LH40-SM1310-D 1310 nm LC 9/125 µm SMF 40 km (24.86 miles)
SFP-GE-LH40-SM1550 1550 nm LC 9/125 µm SMF 40 km (24.86 miles)
PIN #8
PIN #1

Manual version: 6PW103-20180115 BOM: 3123A1J8
iii
GE SFP transceiver
module Central wavelength Connector type Cable specifications
Maximum
transmission
distance
SFP-GE-LH80-SM1550 1550 nm LC 9/125 µm SMF 80 km (49.71 miles)
SFP-GE-LH80-SM1550-D 1550nm LC 9/125 µm SMF 80 km (49.71 miles)
SFP-GE-LH100-SM1550 1550 nm LC 9/125 µm SMF 100 km (62.14 miles)
SFP-GE-LX-SM1310-BIDI RX: 1490 nm
TX: 1310 nm LC 9/125 µm SMF 10 km (6.21 miles)
SFP-GE-LX-SM1490-BIDI RX: 1310 nm
TX: 1490 nm LC 9/125 µm SMF 10 km (6.21 miles)
NOTE:
•BIDI modules use different central wavelengths in transmit and receive directions, in order to
implement bidirectional transmission of optical signals over the same fiber.
•The BIDI modules must be used in pairs. For example, if you install the
SFP-GE-LX-SM1310-BIDI in the local port, you must install the SFP-GE-LX-SM1490-BIDI in the
peer port.
3 Related documentation
For module installation, see H3C S7500X Switch Series Installation Guide.
For software upgrade, see the release notes for the device.
Copyright © 2017-2018 New H3C Technologies Co., Ltd.
The information in this document is subject to change without notice.