H3C S5820 series Installation manual

H3C S5820X&S5800 Switch Series
OAA Command Reference
Hangzhou H3C Technologies Co., Ltd.
http://www.h3c.com
Software version: Release 1805P02
Release 1808P12
Document version: 6W101-20140314

Copyright © 2012-2014, Hangzhou H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior
written consent of Hangzhou H3C Technologies Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care, , IRF, NetPilot, Netflow,
SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of
Hangzhou H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.

Preface
The H3C S5820X&S5800 documentation set includes 12 command references, which describe the
commands and command syntax options available for the S5820X&S5800 Switch Series.
The OAA Command Reference describes OAA configuration commands.
This preface includes:
•Audience
•Added and modified commands
•Conventions
•About the H3C S5820X&S5800 documentation set
•Obtaining documentation
•Technical support
•Documentation feedback
Audience
This documentation is intended for:
•Network planners
•Field technical support and servicing engineers
•Network administrators working with the S5820X&S5800 series
Added and modified commands
This documentation set is for Release 18xx. The following describes the command changes between
releases:
•Release 1808P12 does not have command changes over Release 1805P02.
•Release 1805P02 does not have command changes over Release 1211.
Conventions
This section describes the conventions used in this documentation set.
Command conventions
Convention Descri
p
tion
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.

Convention Descri
p
tion
{ x | y | ... }
Braces enclose a set of required syntax choices separated by vertical bars, from which
you select one.
[ x | y | ... ]
Square brackets enclose a set of optional syntax choices separated by vertical bars, from
which you select one or none.
{ x | y | ... } *
Asterisk marked braces enclose a set of required syntax choices separated by vertical
bars, from which you select at least one.
[ x | y | ... ] *
Asterisk marked square brackets enclose optional syntax choices separated by vertical
bars, from which you select one choice, multiple choices, or none.
&<1-n> The argument or keyword and argument combination before the ampersand (&) sign can
be entered 1 to n times.
# A line that starts with a pound (#) sign is comments.
GUI conventions
Convention Descri
p
tion
Boldface Window names, button names, field names, and menu items are in Boldface. For
example, the New User window appears; click OK.
> Multi-level menus are separated by angle brackets. For example, File > Create > Folder.
Symbols
Convention Descri
p
tion
WARNING An alert that calls attention to important information that if not understood or followed can
result in personal injury.
CAUTION An alert that calls attention to important information that if not understood or followed can
result in data loss, data corruption, or damage to hardware or software.
IMPORTANT An alert that calls attention to essential information.
NOTE An alert that contains additional or supplementary information.
TIP An alert that provides helpful information.
Network topology icons
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that supports
Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the switching engine
on a unified wired-WLAN switch.
Represents an access point.

Represents a security product, such as a firewall, a UTM, or a load-balancing or security
card that is installed in a device.
Represents a security card, such as a firewall card, a load-balancing card, or a
NetStream card.
Port numbering in examples
The port numbers in this document are for illustration only and might be unavailable on your device.
About the H3C S5820X&S5800 documentation set
The H3C S5820X&S5800 documentation set includes:
Cate
g
or
y
Documents Pur
p
oses
Product description and
specifications
Marketing brochures Describe product specifications and benefits.
Technology white papers
Provide an in-depth description of software features
and technologies.
Pluggable module
description
PSR150-A & PSR150-D
Series Power Modules
User Manual
Describes the appearances, features, specifications,
installation, and removal of the pluggable 150W
power modules available for the products.
PSR300-12A &
PSR300-12D Series
Power Modules User
Manual
Describes the appearances, features, specifications,
installation, and removal of the pluggable 300W
power modules available for the products.
LSVM1AC650 &
LSVM1DC650 Power
Modules User Manual
Describes the appearances, features, specifications,
installation, and removal of the pluggable 650W
power modules available for the products.
PSR750-A [ PSR750-D ]
Power Modules User
Manual
Describes the appearances, features, specifications,
installation, and removal of the pluggable 750W
power modules available for the products.
RPS User Manual
Describes the appearances, features, and
specifications of the RPS units available for the
products.
LSW1FAN and
LSW1BFAN Installation
Manual
Describes the appearances, specifications,
installation, and removal of the pluggable fan
modules available for the products.
LSWM1FANSC and
LSWM1FANSCB
Installation Manual
Describes the appearances, specifications,
installation, and removal of the pluggable fan
modules available for the products.
LSW148POEM Module
User Manual
Describes the appearance, features, installation,
and removal of the pluggable PoE module available
for the products.
S5820X [ S5800 ] Series
Ethernet Switches
Interface Cards User
Manual
Describes the models, hardware specifications,
installation, and removal of the interface cards
available for the products.
H3C OAP Cards User
Manual
Describes the benefits, features, hardware
specifications, installation, and removal of the OAP


Cate
g
or
y
Documents Pur
p
oses
cards available for the products.
H3C Low End Series
Ethernet Switches
Pluggable Modules
Manual
Describes the models, appearances, and
specifications of the pluggable modules available
for the products.
Power configuration
S5800-60C-PWR
Ethernet Switch Hot
Swappable Power
Module Ordering Guide
Guides you through ordering the hot-swappable
power modules available for the S5800-60C-PWR
switches in different cases.
RPS Ordering Information
for H3C Low-End Ethernet
Switches
Provides the RPS and switch compatibility matrix and
RPS cable specifications.
Hardware installation
•S5800 Series Ethernet
Switches Quick Start
•S5820X Series
Ethernet Switches
Quick Start
•S5800 Series Ethernet
Switches CE DOC
•S5820X Series
Ethernet Switches CE
DOC
Provides regulatory information and the safety
instructions that must be followed during installation.
•S5800 Series Ethernet
Switches Quick Start
•S5820X Series
Ethernet Switches
Quick Start
Guides you through initial installation and setup
procedures to help you quickly set up and use your
device with the minimum configuration.
•S5800 Series Ethernet
Switches Installation
Manual
•S5820X Series
Ethernet Switches
Installation Manual
Provides a complete guide to hardware installation
and hardware specifications.
Pluggable SFP[SFP+][XFP]
Transceiver Modules
Installation Guide
Guides you through installing SFP/SFP+/XFP
transceiver modules.
•S5800-60C-PWR
Switch Video
Installation Guide
•S5820X-28C Switch
Video Installation
Guide
Shows how to install the H3C S5800-60C-PWR and
H3C S5820X-28C Ethernet switches.
Software configuration
Configuration guide Describe software features and configuration
procedures.
Command reference Provide a quick reference to all available
commands.
Operations and
maintenance
H3C Series Ethernet
Switches Login Password
Tells how to find the lost password or recover the
password when the login password is lost.

Cate
g
or
y
Documents Pur
p
oses
Recovery Manual
Release notes
Provide information about the product release,
including the version history, hardware and software
compatibility matrix, version upgrade information,
technical support information, and software
upgrading.
Obtaining documentation
You can access the most up-to-date H3C product documentation on the World Wide Web
at http://www.h3c.com.
Click the links on the top navigation bar to obtain different categories of product documentation:
[Technical Support & Documents > Technical Documents]—Provides hardware installation, software
upgrading, and software feature configuration and maintenance documentation.
[Products & Solutions]—Provides information about products and technologies, as well as solutions.
[Technical Support & Documents > Software Download]—Provides the documentation released with the
software version.
Technical support
servic[email protected]
http://www.h3c.com
Documentation feedback
You can e-mail your comments about product documentation to [e-mail].
We appreciate your comments.

i
Contents
OAP card configuration commands ··························································································································· 1
oap connect ······························································································································································1
oap reboot ································································································································································1
ACFP configuration commands··································································································································· 3
acfp server enable····················································································································································3
display acfp client-info·············································································································································3
display acfp policy-info············································································································································4
display acfp rule-info················································································································································6
display acfp server-info············································································································································8
ACSEI configuration commands ·······························································································································10
acsei client close···················································································································································· 10
acsei client reboot ················································································································································· 10
acsei server ···························································································································································· 11
acsei server enable ··············································································································································· 11
acsei timer clock-sync············································································································································ 11
acsei timer monitor················································································································································ 12
display acsei client info ········································································································································ 13
display acsei client summary ······························································································································· 14
Index ···········································································································································································16

1
OAP card configuration commands
oap connect
Use oap connect to redirect from the switch to the software system of an OAP card.
Syntax
oap connect slot slot-number system system-name
Views
User view
Default command level
2: System level
Parameters
slot slot-number: Specifies an OAP card on an IRF member switch. The slot-number argument takes the
member ID of the member switch, and its value ranges depend on the number of member switches and
their member IDs.
system system-name: Specifies the system name of the OAP card in the form SubSlotX, where Xis the slot
number of the OAP card. For example, the system name of the OAP card in slot 3 is SubSlot3.
Usage guidelinesWhen this command is executed, the terminal display interface is switched from the CLI
on the switch to the operating interface of the software system of the OAP card, and you can manage the
system and application software on the OAP card.
To return from the software system on the OAP card to the CLI of the switch, press Ctrl+K.
You can install multiple OAP cards on some models of the S5800 and S5820X switches. If you log in to
the software system of one OAP card first, you cannot log in to the software system of another by using
the oap connect command. To log in to the software system of another OAP card, return to the CLI on the
switch by pressing Ctrl+K first.
In an IRF fabric, you can use the oap connect command multiple times to log in to the software systems
of multiple OAP cards installed on different member switches, but cannot log in to the software systems
of multiple OAP cards installed on the same member switch simultaneously.
Examples
# Redirect from the switch to the software system of the OAP card in slot 3 of the member switch 1.
<Sysname> oap connect slot 1 system SubSlot3
Press CTRL+K to quit.
Connected to SubSlot3
oap reboot
Use oap reboot to restart the software system of an OAP card.
Syntax
oap reboot slot slot-number system system-name

2
Views
User view
Default command level
2: System level
Parameters
slot slot-number: Restarts the software system of an OAP card on an IRF member switch. The slot-number
argument takes the member ID of the member of the IRF fabric, and its value ranges depend on the
number of member switches and their member IDs.
system system-name: Specifies the system name of the OAP card in the form SubSlotX, where Xis the slot
number of the OAP card. For example, the system name of the OAP card in slot 3 is SubSlot3.
Examples
# Restart the software system of the OAP card in slot 3 of member switch 1.
<Sysname> oap reboot slot 1 system SubSlot3
This command will recover the SubSlot3 from shutdown or other failed state.
Warning: This command may lose the data on the hard disk if the SubSlot1 is not
being shut down! Continue? [Y/N]:y
Reboot SubSlot1 by command.

3
ACFP configuration commands
acfp server enable
Use acfp server enable to enable the ACFP server.
Use undo acfp server enable to disable the ACFP server.
Syntax
acfp server enable
undo acfp server enable
Default
The ACFP server is disabled.
Views
System view
Default command level
2: System level
Usage guidelines
In case that the ACSEI server is enabled on the device, when you first disable and then enable the ACFP
server, to make sure the ACFP collaboration rules can be resent to the ACFP server, you must also disable
and then enable the ACSEI server.
Examples
# Enable the ACFP server.
<Sysname> system-view
[Sysname] acfp server enable
Related commands
acsei server enable
display acfp client-info
Use display acfp client-info to display the information about the specified ACFP clients.
Syntax
display acfp client-info [ client-id ] [ |{ begin | exclude | include } regular-expression ]
Views
Any view
Default command level
1: Monitor level

4
Parameters
client-id: Displays information of the specified ACFP client, where client-id is the ACFP client identifier, in
the range of 1 to 2147483647.
|: Filters command output by specifying a regular expression. For more information about regular
expressions, see Fundamentals Configuration Guide.
begin: Displays the first line that matches the specified regular expression and all lines that follow.
exclude: Displays all lines that do not match the specified regular expression.
include: Displays all lines that match the specified regular expression.
regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.
Usage guidelines
If no ACFP client ID is specified, the information about all ACFP clients is displayed.
Examples
# Display the information about all ACFP clients.
<Sysname> display acfp client-info
ACFP client total number: 1
ClientID: 2
Description: Intrusion Prevention System
Hw-Info: 2.0
OS-Info: i-Ware software, Version 1.10
App-Info: Ess 2110P01
Client IP: 10.1.1.1
Client Mode: redirect mirror
Table 1 Command output
Field Descri
p
tion
ACFP client total number Total number of ACFP clients.
ClientID Client ID, index of ACFP client list.
Description Description information of ACFP client.
Hw-Info Hardware information of the ACFP client.
OS-Info Operating system information of the ACFP client.
App-Info Application software information of the ACFP client.
Client IP ACFP client IP address.
Client Mode
Operating mode supported on the ACFP client:
•redirect—redirect mode.
•mirror—mirror mode.
display acfp policy-info
Use display acfp policy-info to display the ACFP policy information.

5
Syntax
display acfp policy-info [ client client-id [ policy-index ] | dest-interface interface-type interface-number
| in-interface interface-type interface-number | out-interface interface-type interface-number ] [ active |
inactive ] [ |{ begin | exclude | include } regular-expression ]
Views
Any view
Default command level
1: Monitor level
Parameters
client client-id: Displays the policy sent by the specified ACFP client, where client-id is the ACFP client ID,
in the range of 1 to 2147483647.
policy-index: Specifies the policy index, in the range of 1 to 2147483647.
dest-interface interface-type interface-number: Displays all policies that use the specified interface
(destination interface) for connecting to the ACFP client, where interface-type interface-number is the
interface type and interface number.
in-interface interface-type interface-number: Displays all policies that use the specified interface as the
inbound interface, where interface-type interface-number is the interface type and interface number.
out-interface interface-type interface-number: Displays all policies that use the specified interface as the
outbound interface, where interface-type interface-number is the interface type and interface number.
active: Displays active policies only.
inactive: Displays inactive policies only.
|: Filters command output by specifying a regular expression. For more information about regular
expressions, see Fundamentals Configuration Guide.
begin: Displays the first line that matches the specified regular expression and all lines that follow.
exclude: Displays all lines that do not match the specified regular expression.
include: Displays all lines that match the specified regular expression.
regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.
Usage guidelines
When you use this command to display the policy information sent by the specified ACFP client, if you
specify the policy-index argument, the command displays the information about the policy whose
number is policy-index applied by the ACFP client with an ID of client-id. Otherwise, the command
displays information about all policies sent by the ACFP client with an ID of client-id.
If neither the active nor inactive keyword is specified, the command displays all active or inactive
policies.
If no argument is specified, the command displays the information about all policies.
Examples
# Display information about the effective policies for all packets that use GigabitEthernet 1/0/1 as the
inbound interface.
<Sysname> display acfp policy-info in-interface gigabitethernet 1/0/1 active
ACFP policy total number: 1
ClientID: 3 Policy-Index: 2

6
Rule-Num: 1 ContextID: 128
Exist-Time: 61500 (s) Life-Time: 2147483647(s)
Start-Time: 00:00:00 End-Time: 24:00:00
Admin-Status: enable Effect-Status: active
DstIfFailAction: delete Priority: 1
In-Interface: GigabitEthernet1/0/1
Out-Interface: GigabitEthernet1/0/2
Dest-Interface: Ten-GigabitEthernet3/0/1
Table 2 Command output
Field Descri
p
tion
ACFP policy total number Total number of ACFP policies.
ClientID Client ID, client list index.
Policy-Index Policy index.
Rule-Num Number of rules under the policy.
ContextID Context ID.
Exist-Time Policy existed time, in seconds.
Life-Time Policy expiration time, in seconds.
Start-Time Policy start time.
End-Time Policy end time.
Admin-Status Policy administration status.
Effect-Status Whether the policy is effective.
DestIfFailAction
If the policy dest-interface is down, the actions to all rules under the
policy are as follows:
•delete—Keep the redirected and mirrored packets being
forwarded. For forwarding-first devices, select the delete action.
•reserve—Discard the redirected and mirrored packets. For
security-first devices, select the reserve action.
Priority Priority of a policy, number notation, in the range of 1 to 8. The bigger
the number, the higher the priority.
In-Interface Inbound interface of the packet.
Out-Interface Outbound interface of the packet.
Dest-Interface Interface connected to the ACFP client.
display acfp rule-info
Use display acfp rule-info to display ACFP rule information.
Syntax
display acfp rule-info { in-interface [ interface-type interface-number ] | out-interface [ interface-type
interface-number ] | policy [ client-id policy-index ] } [ |{ begin | exclude | include } regular-expression ]
Views
Any view

7
Default command level
1: Monitor level
Parameters
in-interface: Displays ACFP rule information in order of inbound interface. The ACFP rule information
which does not include the inbound interface is not displayed.
out-interface: Displays ACFP rule information in order of outbound interface. The ACFP rule information
which does not include the outbound interface is not displayed.
interface-type interface-number: Specifies an interface by its type and number.
policy: Displays the ACFP rule information in order of policy.
client-id: ACFP client ID, in the range of 1 to 2147483647.
policy-index: Policy index, in the range of 1 to 2147483647.
|: Filters command output by specifying a regular expression. For more information about regular
expressions, see Fundamentals Configuration Guide.
begin: Displays the first line that matches the specified regular expression and all lines that follow.
exclude: Displays all lines that do not match the specified regular expression.
include: Displays all lines that match the specified regular expression.
regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.
Usage guidelines
When you use this command to display ACFP rule information in order of policy, if you specify neither
client ID nor policy index, the rule information of all policies is displayed.
When you use this command to display ACFP rule information in order of outbound/inbound interface,
if you specify no interface, the rule information for all inbound interfaces or outbound interfaces is
displayed.
Examples
# Display ACFP rule information in order of inbound interface.
<Sysname> display acfp rule-info in-interface gigabitethernet 1/0/1
In-Interface: GigabitEthernet1/0/1
ACFP rule total number: 1
ClientID:1 Policy-Index:1 Rule-Index:1
SIP:192.168.1.1 SMask:0.0.0.255
Action:redirect Status:active OperationStatus:succeeded
# Display ACFP rule information in order of policy.
<Sysname> display acfp rule-info policy 1 1
ACFP Rule total number: 1
ClientID:1 Policy-Index:1 Rule-Index:1
SIP:192.168.1.1 SMask:0.0.0.255 SPort:65500 to 65535
DIP:192.168.2.1 DMask:0.0.0.255 DPort:65500 to 65535
Protocol:ip Fragment:false DSCP:AF11
Action:redirect Status:active OperationStatus:succeeded

8
Table 3 Command output
Field Descri
p
tion
In-Interface Inbound interface of the packet.
ACFP rule total number Total number of ACFP rules.
ClientID Client ID, client list index.
Policy-Index Policy index.
Rule-Index Rule index.
SIP Source IP address.
SMask Inverse mask of source IP address.
SPort Source port number.
DIP Destination IP address.
DMask Inverse mask of destination IP address.
DPort Destination port number.
Protocol Protocol of the packet: GRE, ICMP, IGMP, IPinIP, OSPF, TCP, UDP, IP, and so on.
Fragment
Whether the packet is a fragment:
•true—The packet is a fragment.
•false—All packets, whether or not the packets are fragments.
ToS Type of Service, indicated by a number in the range of 0 to 15.
Pre Packet precedence, indicated by a number in the range of 0 to 7.
DSCP
Differentiated Services Code Point, indicated by characters for Be, Ef, Af11,
Af12, Af13, Af21, Af22, Af23, Af31, Af32, Af33, Af41, Af42, Af43, Cs1,
Cs2, Cs3, Cs4, Cs5, Cs6, and Cs7 and indicated by a number in the range 0
to 63 for other code points.
TCPFlag The value is six bits, which represents URG, ACK, PSH, RST, SYN, and FIN from
low to high.
TCPMask
The value is six bits, which represents URG mask, ACK mask, PSH mask, RST
mask, SYN mask, and FIN mask from low to high.
For each bit, the value 1 indicates that this bit is concerned, and the value 0
indicates that this bit is not concerned.
Action
Action:
•permit.
•deny.
•mirror.
•redirect.
•rate—rate limit.
Status Rule status, active or inactive.
OperationStatus Rule application status, succeeded or failed.
display acfp server-info
Use display acfp server-info to display ACFP server information.

9
Syntax
display acfp server-info [ |{ begin | exclude | include } regular-expression ]
Views
Any view
Default command level
1: Monitor level
Parameters
|: Filters command output by specifying a regular expression. For more information about regular
expressions, see Fundamentals Configuration Guide.
begin: Displays the first line that matches the specified regular expression and all lines that follow.
exclude: Displays all lines that do not match the specified regular expression.
include: Displays all lines that match the specified regular expression.
regular-expression: Specifies a regular expression, a case-sensitive string of 1 to 256 characters.
Examples
# Display ACFP server information.
<Sysname> display acfp server-info
Server-Info: ipserver redirect mirror
Max Life-Time: 2147483647(s)
PersistentRules: false
ContextType: HGPlus-context
Table 4 Command output
Field Descri
p
tion
Server-Info
ACFP client operating mode supported by the ACFP server:
•ipserver—Host mode.
•redirect—Redirect mode.
•mirror—Mirror mode.
The switches support only the redirect and mirror modes.
Max Life-Time Maximum expiration time (in seconds) of the collaboration policy supported by
the ACFP server.
PersistentRules Whether the ACFP server supports permanent collaboration rules.
ContextType
Context ID types supported by the ACFP server:
•no-context—No context ID is carried.
•HG-context—Carrying the preamble HG as the context ID.
•HGPlus-context—Carrying the preamble HGPlus as the context ID.
•FlowID-context—Carrying the preamble Flow ID as the context ID.
•VLANID-context—Carrying VLAN ID as the context ID.
The switches support only the HGPlus-context.

10
ACSEI configuration commands
acsei client close
Use acsei client close to close an ACSEI client.
Syntax
acsei client close client-id
Views
ACSEI server view
Default command level
2: System level
Parameters
client-id: ID of the ACSEI client to be closed, in the range of 1 to 10. An ACSEI client ID is assigned by
the ACSEI server.
Usage guidelines
Once the command is executed, the ACSEI server sends an inform packet for the close operation to the
specified ACSEI client, that will then execute the close operation.
This command is available only for an ACSEI client supporting Linux operating system.
Examples
# Close ACSEI client 1.
<Sysname> system-view
[Sysname] acsei server
[Sysname-acsei-server] acsei client close 1
acsei client reboot
Use acsei client reboot to restart an ACSEI client.
Syntax
acsei client reboot client-id
Views
ACSEI server view
Default command level
2: System level
Parameters
client-id: ID of the ACSEI client to be restarted, in the range of 1 to 10.
Examples
# Restart ACSEI client 1.

11
<Sysname> system-view
[Sysname] acsei server
[Sysname-acsei-server] acsei client reboot 1
acsei server
Use acsei server to enter ACSEI server view.
Syntax
acsei server
Views
System view
Default command level
2: System level
Examples
# Enter ACSEI server view.
<Sysname> system-view
[Sysname] acsei server
[Sysname-acsei-server]
acsei server enable
Use acsei server enable to enable ACSEI server.
Use undo acsei server enable to disable ACSEI server.
Syntax
acsei server enable
undo acsei server enable
Default
ACSEI server is disabled.
Views
System view
Default command level
2: System level
Examples
# Enable ACSEI server.
<Sysname> system-view
[Sysname] acsei server enable
acsei timer clock-sync
Use acsei timer clock-sync to set the synchronization timer that is used for clock synchronization from the
ACSEI server to the ACSEI client.

12
Use undo acsei timer clock-sync to restore the default.
Syntax
acsei timer clock-sync minutes
undo acsei timer clock-sync
Default
The clock sychronization timer is set to five minutes.
Views
ACSEI server view
Default command level
2: System level
Parameters
minutes: Value of the synchronization timer that is used for clock synchronization from ACSEI server to
ACSEI client. It ranges from 0 to 1440 (in minutes), where value 0 specifies to disable the clock
synchronization from ACSEI server to ACSEI client.
Examples
# Set the clock synchronization timer from ACSEI server to ACSEI client to 20 minutes.
<Sysname> system-view
[Sysname] acsei server
[Sysname-acsei-server] acsei timer clock-sync 20
acsei timer monitor
Use acsei timer monitor to set the monitoring timer for ACSEI server to monitor ACSEI client.
Use undo acsei timer monitor to restore the default.
Syntax
acsei timer monitor seconds
undo acsei timer monitor
Default
The monitoring timer is set to 5 seconds.
Views
ACSEI server view
Default command level
2: System level
Parameters
seconds: Sepcifies the value of the monitoring timer that is used for the ACSEI server to monitor ACSEI
clients. It ranges from 0 to 10 (in seconds), where 0 specifies to disable ACSEI server from monitoring
ACSEI client.
Examples
# Set the monitor timer for ACSEI server to monitor ACSEI client to 6 seconds.