H3C S10506 Operating and maintenance manual

H3C S10500 Switch Series
Installation Quick Start
New H3C Technologies Co., Ltd.
http://www.h3c.com.hk
Document version: 6PW103-20170430

Copyright © 2016-2017, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior
written consent of New H3C Technologies Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care, , IRF, NetPilot, Netflow,
SecEngine, SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New
H3C Technologies Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.
Environmental protection
This product has been designed to comply with the environmental protection requirements. The storage,
use, and disposal of this product must meet the applicable national laws and regulations.

i
Contents
Installation quick start ·················································································································································· 1
Chassis views and technical specifications····················································································································1
Chassis views····························································································································································1
Technical specifications ···········································································································································2
Safety recommendations ··················································································································································3
Examining the installation site ·········································································································································4
Installing the switch ···························································································································································4
Attaching the slide rails to the rack ························································································································4
Installing cage nuts···················································································································································5
Installing the switch in the rack ·······························································································································7
Grounding the switch···············································································································································7
Installing FRUs···························································································································································8
Installing a power module ···································································································································· 10
Connecting power cords ······································································································································ 11
Accessing the switch for the first time ·························································································································· 12
Connecting the console cable······························································································································ 12
Setting terminal parameters·································································································································· 13
Powering on the switch········································································································································· 14
Obtaining documentation ············································································································································· 14
Index ···········································································································································································15

1
Installation quick start
This installation quick start provides basic instructions for installing an S10500 switch. For more
information about the installation procedure, see H3C S10500 Switch Series Installation Guide.
The installation procedure is similar for all S10500 switch models. This installation quick start uses the
S10508-V switch as an example.
NOTE:
The figures in this installation quick start are for illustration only.
Chassis views and technical specifications
Chassis views
Figure 1 Chassis
S10504 S10508
S10508-V S10512
S10506
S10510

2
Figure 2 S10508-V switch front and rear panels
(1) LPU slots (2) MPU slots
(3) Power module slots (4) Fan tray slot
(5) Switchin
g
fabric module slots
Technical specifications
Table 1 Switch dimensions
Model Hei
g
ht Width De
p
th
S10504 353 mm (13.90 in) (8 RU) 440 mm (17.32 in) 660 mm (25.98 in)
S10506 353 mm (13.90 in) (8 RU) 440 mm (17.32 in) 660 mm (25.98 in)
S10508 620 mm (24.41 in) (14 RU) 440 mm (17.32 in) 660 mm (25.98 in)
S10508-V 886 mm (34.88 in) (20 RU) 440 mm (17.32 in) 660 mm (25.98 in)
S10510 620 mm (24.41 in) (14 RU) 440 mm (17.32 in) 660 mm (25.98 in)
S10512 797 mm (31.38 in) (18 RU) 440 mm (17.32 in) 660 mm (25.98 in)
Table 2 Power module specifications
Item LSUM1AC1200
s
p
ecifications
LSUM1AC2500
s
p
ecifications
LSUM1DC2400
s
p
ecifications
Rated input voltage
range
100 VAC to 240 VAC @
50/60 Hz
100 VAC to 240 VAC @
50/60 Hz –48 VDC to –60 VDC
12
3
1
5
4

3
Item LSUM1AC1200
s
p
ecifications
LSUM1AC2500
s
p
ecifications
LSUM1DC2400
s
p
ecifications
Rated output voltage 12 VDC 12 VDC 12 VDC
Maximum input current 16 A 16 A 60 A
Maximum output
current 100 A
•100 A (110 VAC)
•208 A (220 VAC) 200 A
Maximum output
power 1200 W
•1200 W (110 VAC)
•2500 W (220 VAC) 2400 W
Quantity
•S10504/S10506: 1 to 4
•S10508/S10508-V/S10510/S10512: 1 to 6
Safety recommendations
To avoid equipment damage or bodily injury caused by improper use, read the following safety
recommendations before installation. Note that the recommendations do not cover every possible
hazardous condition.
•To prevent ESD damage, always wear an ESD wrist strap and make sure it is reliably grounded
before you touch the switch, cards, or PCB.
•Do not install the switch, FRUs, or cables when the switch is powered on.
•To avoid equipment damage or bodily injury, make sure the switch is reliably grounded before
powering on the switch.
•To ensure good ventilation, install a blank filler panel in an unused slot.
Figure 3 Attaching an ESD wrist strap

4
Examining the installation site
The switch can only be used indoors. To make sure the switch operates correctly and prolong its service
lifetime, the installation site must meet the requirements for load-bearing, temperature, humidity,
cleanness, EMI, grounding power module, ventilation, and space. For more information, see H3C
S10500 Switch Series Installation Guide.
Installing the switch
Attaching the slide rails to the rack
1. Read the signs on the slide rails to identify the left and right slide rails and their front ends, as
shown in Table 3.
Table 3 Description for signs on the slide rails
Si
g
nMeanin
g
Remarks
F/L Front end of the left slide rail Mount this end to the front left rack post.
F/R Front end of the right slide rail Mount this end to the front right rack post.
2. Mark the installation position on the rack for the slide rails:
a. Make sure the top flange of a slide rail aligns with the middle of the narrower metal area
between holes in a rack post, as shown in Figure 4.
b. Each rack post requires six screws to attach the slide rail. Mark only the uppermost and
lowermost holes.
c. Mark the square holes at the same height on the other three rack posts.
Figure 4 Determining the cage nut installation holes by using a slide rail
(1) Middle of the narrower metal area between holes
3. Install six cage nuts in the square holes in each rack post, as shown in Figure 5.

5
Figure 5 Installing a cage nut
4. Align the installation holes on the front end of a slide rail with the cage nuts on a front rack post,
and use six screws to attach the slide rail to the front rack post. Figure 6 uses the right slide rail as
an example.
Figure 6 Attaching the right slide rail to the front right rack post
5. Keep the slide rail horizontal and adjust its length until the installation holes on the rear end of the
slide rail touch the cage nuts on the rear rack post. Then use screws to attach the slide rail to the
rear rack post.
6. Repeat steps 4 and 5 to install the other slide rail. Make sure the two slide rails are at the same
height so that the switch can be placed on them horizontally.
Installing cage nuts
1. Determine and mark the cage nut installation holes in either of the following methods:
{Mark the cage nut installation holes as shown in Figure 7.
12

6
{Use other tools such as a tape. Align the tape with a mounting bracket. Mark the tape
according to the cage nut installation holes on the mounting bracket. Align the tape with the
rack posts and mark the installation holes on the rack posts.
For the S10506 and S10510 switches, you can use the cage nut installation template to determine
the cage nut installation holes on the rack posts. For more information about the cage nut
installation template, see H3C S10506&S10510 Switches Installation Quick Start.
Figure 7 Cage nut installation holes
Figure 8 Marking the cage nut installation holes
S10504 S10508 S10508-V S10512S10506 S10510
Chassis Middle of the narrower metal area between holes
Cage nut installation holes

7
2. Install the cage nuts in the marked square holes on the rack posts.
Installing the switch in the rack
Follow these guidelines when you install the switch in the rack:
•To avoid equipment damage or bodily injury, use a minimum of two people to lift the switch. H3C
recommends that you use a mechanical lift to move the switch.
•Do not hold the filler panels, filler panel handles, or the air vents of chassis to carry the chassis. Any
attempt to carry the switch with these parts might cause equipment damage or even bodily injury.
•After placing the switch on the slide rails, do not leave go of your hands immediately because this
might tip the switch. Tipping the switch can cause switch damage and even bodily injury.
Figure 9 Installing the switch in the rack
Grounding the switch
CAUTION:
•Use the provided grounding cable (yellow-green grounding cable).
•Connect the
g
roundin
g
cable to the
g
roundin
g
system in the equipment room. Do not connect it to a fire
main or lightning rod.