H3C S6820 Series Installation manual

H3C S6820 Switch Series
OpenFlow Command Reference
New H3C Technologies Co., Ltd.
http://www.h3c.com.hk
Software version: Release 612x
Document version: 6W101-20170815

Copyright © 2017, New H3C Technologies Co., Ltd. and its licensors
All rights reserved
No part of this manual may be reproduced or transmitted in any form or by any means without prior written
consent of New H3C Technologies Co., Ltd.
Trademarks
H3C, , H3CS, H3CIE, H3CNE, Aolynk, , H3Care, , IRF, NetPilot, Netflow, SecEngine,
SecPath, SecCenter, SecBlade, Comware, ITCMM and HUASAN are trademarks of New H3C Technologies
Co., Ltd.
All other trademarks that may be mentioned in this manual are the property of their respective owners
Notice
The information in this document is subject to change without notice. Every effort has been made in the
preparation of this document to ensure accuracy of the contents, but all statements, information, and
recommendations in this document do not constitute the warranty of any kind, express or implied.

Preface
This command reference describes the OpenFlow configuration commands.
This preface includes the following topics about the documentation:
•Audience
•Conventions
•Obtaining documentation
•Technical support
•Documentation feedback
Audience
This documentation is intended for:
•Network planners.
•Field technical support and servicing engineers.
•Network administrators working with the S6820 switch series.
Conventions
The following information describes the conventions used in the documentation.
Command conventions
Convention
Description
Boldface Bold text represents commands and keywords that you enter literally as shown.
Italic Italic text represents arguments that you replace with actual values.
[ ] Square brackets enclose syntax choices (keywords or arguments) that are optional.
{ x | y | ... }
Braces enclose a set of required syntax choices separated by vertical bars, from which
you select one.
[ x | y | ... ]
Square brackets enclose a set of optional syntax choices separated by vertical bars,
from which you select one or none.
{ x | y | ... } *
Asterisk marked braces enclose a set of required syntax choices separated by vertical
bars, from which you select a minimum of one.
[ x | y | ... ] *
Asterisk marked square brackets enclose optional syntax choices separated by vertical
bars, from which you select one choice, multiple choices, or none.
&<1-n> The argument or keyword and argument combination before the ampersand (&) sign
can be entered 1 to n times.
# A line that starts with a pound (#) sign is comments.
GUI conventions
Convention
Description
Boldface Window names, button names, field names, and menu items are in Boldface. For
example, the New User window opens; click OK.
> Multi-level menus are separated by angle brackets. For example, File > Create >

Convention
Description
Folder.
Symbols
Convention
Description
WARNING! An alert that calls attention to important information that if not understood or followed
can result in personal injury.
CAUTION: An alert that calls attention to important information that if not understood or followed
can result in data loss, data corruption, or damage to hardware or software.
IMPORTANT:
An alert that calls attention to essential information.
NOTE: An alert that contains additional or supplementary information.
TIP:
An alert that provides helpful information.
Network topology icons
Convention
Description
Represents a generic network device, such as a router, switch, or firewall.
Represents a routing-capable device, such as a router or Layer 3 switch.
Represents a generic switch, such as a Layer 2 or Layer 3 switch, or a router that
supports Layer 2 forwarding and other Layer 2 features.
Represents an access controller, a unified wired-WLAN module, or the access
controller engine on a unified wired-WLAN switch.
Represents an access point.
Represents a wireless terminator unit.
Represents a wireless terminator.
Represents a mesh access point.
Represents omnidirectional signals.
Represents directional signals.
Represents a security product, such as a firewall, UTM, multiservice security
gateway, or load balancing device.
Represents a security module, such as a firewall, load balancing, NetStream, SSL
VPN, IPS, or ACG module.
T
T
T
T

Examples provided in this document
Examples in this document might use devices that differ from your device in hardware model,
configuration, or software version. It is normal that the port numbers, sample output, screenshots,
and other information in the examples differ from what you have on your device.
Obtaining documentation
To access the most up-to-date H3C product documentation, go to the H3C website at
http://www.h3c.com.hk
To obtain information about installation, configuration, and maintenance, click
http://www.h3c.com.hk/Technical_Documents
To obtain software version information such as release notes, click
http://www.h3c.com.hk/Software_Download
Technical support
[e-mail]
http://www.h3c.com.hk
Documentation feedback
You can e-mail your comments about product documentation to [email protected].
We appreciate your comments.

i
Contents
OpenFlow commands ·······································································1
active instance····················································································································1
classification·······················································································································1
controller address················································································································2
controller auxiliary ···············································································································3
controller connect interval ·····································································································4
controller echo-request interval ······························································································5
controller mode···················································································································5
datapath-id·························································································································6
default table-miss permit·······································································································7
description·························································································································7
display openflow ·················································································································8
display openflow auxiliary······································································································9
display openflow flow-table·································································································· 10
display openflow group·······································································································15
display openflow instance ··································································································· 16
display openflow meter·······································································································18
display openflow summary ··································································································20
fail-open mode·················································································································· 21
flow-entry max-limit············································································································ 22
flow-log disable················································································································· 22
flow-table························································································································· 23
forbidden port··················································································································· 24
in-band management vlan···································································································24
listening port····················································································································· 25
mac-ip dynamic-mac aware·································································································26
mac-learning forbidden······································································································· 26
openflow instance··············································································································27
openflow lossless enable ····································································································27
permit-port-type member-port ······························································································28
precedence dynamic arp·····································································································29
protocol-packet filter slow····································································································29
qinq-network enable···········································································································30
refresh ip-flow··················································································································· 30
reset openflow instance statistics·························································································· 31
tcp dscp ·························································································································· 31
tcp-connection backup········································································································32
Index···························································································33

1
OpenFlow commands
active instance
Use active instance to activate an OpenFlow instance.
Use undo active instance to deactivate an OpenFlow instance.
Syntax
active instance
undo active instance
Default
An OpenFlow instance is not activated.
Views
OpenFlow instance view
Predefined user roles
network-admin
Usage guidelines
If the VLAN configuration or flow table configuration of an activated OpenFlow instance is changed,
use this command to reactivate the instance. After the OpenFlow instance is reactivated, it
re-establishes connections to controllers if the OpenFlow instance was connected to the controllers
before the reactivation.
Examples
# Activate OpenFlow instance 1.
<Sysname> system-view
[Sysname] openflow instance 1
[Sysname-of-inst-1] active instance
classification
Use classification to configure the OpenFlow instance mode.
Use undo classification to restore the default.
Syntax
classification { global | vlan vlan-id [ mask vlan-mask ] [ loosen ] }
undo classification
Default
The OpenFlow instance mode is not configured.
Views
OpenFlow instance view
Predefined user roles
network-admin

2
Parameters
global: Specifies the global mode.
vlan: Specifies the VLAN mode.
vlan-id: Specifies a VLAN ID in the range of 1 to 4094.
vlan-mask: Specifies a VLAN mask in the range of 0 to 4095. The default value is 4095.
loosen: Specifies the loosen mode. If the loosen mode is used, a port belongs to the OpenFlow
instance when VLANs associated with the OpenFlow instance overlap with the port's allowed
VLANs. If you do not specify the loosen mode, a port belongs to an OpenFlow instance only when
VLANs associated with the OpenFlow instance are within the port's allowed VLAN list.
Usage guidelines
The VLANs to be associated are calculated by a bitwise AND operation on the specified VLAN ID
and mask. The VLAN mask supports non-contiguous 1s and ignores all 0 bits. To view the
associated VLANs, use the display openflow instance command.
If you execute this command multiple times, the most recent configuration takes effect.
Examples
# Enable the VLAN mode for OpenFlow instance 1 and associate OpenFlow instance 1 with VLANs
determined by VLAN ID 255 and VLAN mask 7.
<Sysname> system-view
[Sysname] openflow instance 1
[Sysname-of-inst-1] classification vlan 255 mask 7
Related commands
display openflow instance
controller address
Use controller address to specify a controller for an OpenFlow switch and configure the main
connection to the controller.
Use undo controller address to delete the main connection to the specified controller.
Syntax
controller controller-id address { ip ipv4-address | ipv6 ipv6-address } [ port port-number ] [local
address { ip local-ipv4-address | ipv6 local-ipv6-address } [ port local-port-number ] ] [ ssl
ssl-policy-name ] [ vrf vrf-name ]
undo controller controller-id address
Default
An OpenFlow instance does not have a main connection to a controller.
Views
OpenFlow instance view
Predefined user roles
network-admin
Parameters
controller-id: Specifies a controller by its ID in the range of 0 to 63.
ip ipv4-address: Specifies the IPv4 address of the controller.
ipv6 ipv6-address: Specifies the IPv6 address of the controller.

3
port port-number: Sets the port number used by the controller to establish TCP connections to the
OpenFlow switch. The value range for the port number is 1 to 65535. The default value is 6633.
local address: Specifies the source IP address used to establish TCP connections to the controller.
When multiple routes are available between a controller and a switch, you can use this keyword to
configure a source IP address for the switch. When the switch restarts or an active/standby
switchover occurs, the switch can use the original route to reconnect to the controller without
selecting a new route.
ip local-ipv4-address: Specifies the source IPv4 address.
ipv6 local-ipv6-address: Specifies the source IPv6 address.
port local-port-number: Specifies the source port number in the range of 1 to 65535. If you do not
specify this option, the system automatically assigns a source port number for establishing the main
connection to the controller.
ssl ssl-policy-name: Specifies the SSL client policy that the controller uses to authenticate the
OpenFlow switch. The ssl-policy-name argument is a case-insensitive string of 1 to 31 characters.
You must configure a separate SSL client policy for the main connection to each controller.
vrf vrf-name: Specifies an MPLS L3VPN instance by its name, a case-sensitive string of 1 to 31
characters. If you do not specify a VRF name, the controller is in the public network.
Usage guidelines
You can specify multiple controllers for an OpenFlow switch. The OpenFlow channel between the
OpenFlow switch and each controller can have only one main connection.
The OpenFlow switch uses the main connection to a controller to exchange control messages with
the controller to perform the following operations:
•Receive flow table entries or data from the controller.
•Report information to the controller.
As a best practice, configure a unicast IP address for a controller. An OpenFlow switch might fail to
establish a connection with the controller that does not use a unicast IP address.
As a best practice, configure a unicast source IPaddress that is the IPaddress of a port belonging to
the OpenFlow instance. If the source IP address is not a unicast address of a port belonging to the
OpenFlow instance, the OpenFlow switch might fail to establish a connection with the controller.
Examples
# Specify controller 1 for OpenFlow instance 1. The controller's IP address is 1.1.1.1 and the port
number is 6666.
<Sysname> system-view
[Sysname] openflow instance 1
[Sysname-of-inst-1] controller 1 address ip 1.1.1.1 port 6666
controller auxiliary
Use controller auxiliary to specify a controller for an OpenFlow switch and configure an auxiliary
connection to the controller.
Use undo controller auxiliary to delete the specified auxiliary connection to the specified controller.
Syntax
controller controller-id auxiliary auxiliary-id transport { tcp | udp | ssl ssl-policy-name }[address
{ ip ipv4-address | ipv6 ipv6-address } ] [ port port-number ]
undo controller id auxiliary auxiliary-id

4
Default
An OpenFlow instance does not have auxiliary connections to a controller.
Views
OpenFlow instance view
Predefined user roles
network-admin
Parameters
controller-id: Specifies a controller by its ID in the range of 0 to 63.
auxiliary auxiliary-id: Specifies an auxiliary connection ID in the range of 1 to 255.
transport: Specifies the transport layer protocol.
tcp: Specifies TCP connections.
udp: Specifies UDP connections.
ssl ssl-policy-name: Specifies the SSL client policy that the controller uses to authenticate the
OpenFlow switch. The ssl-policy-name argument is a case-insensitive string of 1 to 31 characters.
ip ipv4-address: Specifies the IPv4 address of the controller.
ipv6 ipv6-address: Specifies the IPv6 address of the controller.
port port-number: Sets the port number used to establish TCP connections to the controller. The
value range for the port number is 1 to 65535. The default value is 6633.
Usage guidelines
The OpenFlow channel might have one main connection and multiple auxiliary connections.
Auxiliary connections are used to improve the communication performance between the controller
and OpenFlow switches.
Make sure the configuration of an auxiliary connection does not conflict with the configuration of the
main connection. Otherwise, the auxiliary connection cannot be established.
An auxiliary connection can have a different destination IP address and port number than the main
connection. If no destination IP address and port number are specified, the auxiliary connection uses
the destination IP address and port number configured for the main connection.
Examples
# Specify controller 1 for OpenFlow instance 1 and configure auxiliary connection 1 to the controller.
<Sysname> system-view
[Sysname] openflow instance 1
[Sysname-of-inst-1] controller 10 auxiliary 1 transport tcp
controller connect interval
Use controller connect interval to set the interval for an OpenFlow instance to reconnect to a
controller.
Use undo controller connect interval to restore the default.
Syntax
controller connect interval interval
undo controller connect interval
Default
An OpenFlow instance reconnects to a controller every 60 seconds.

5
Views
OpenFlow instance view
Predefined user roles
network-admin
Parameters
interval: Specifies the reconnection interval in the range of 10 to 120 seconds.
Examples
# Configure OpenFlow instance 1 to reconnect to a controller every 10 seconds.
<Sysname> system-view
[Sysname] openflow instance 1
[Sysname-of-inst-1] controller connect interval 10
controller echo-request interval
Use controller echo-request interval to set the echo request interval for an OpenFlow switch.
Use undo controller echo-request interval to restore the default.
Syntax
controller echo-request interval interval
undo controller echo-request interval
Default
The echo request interval is 5 seconds for an OpenFlow switch.
Views
OpenFlow instance view
Predefined user roles
network-admin
Parameters
interval: Specifies the echo request interval in the range of 1 to 10 seconds.
Examples
# Set the echo request interval to 10 seconds for OpenFlow instance 1.
<Sysname> system-view
[Sysname] openflow instance 1
[Sysname-of-inst-1] controller echo-request interval 10
controller mode
Use controller mode to set the controller mode for an OpenFlow instance.
Use undo controller mode to restore the default.
Syntax
controller mode { multiple | single }
undo controller mode

6
Default
The controller mode is multiple.
Views
OpenFlow instance view
Predefined user roles
network-admin
Parameters
multiple: Specifies the multiple mode.
single: Specifies the single mode.
Usage guidelines
In single mode, the OpenFlow switch connects to only one controller at a time. When
communication with the current controller fails, the OpenFlow instance connects to the controller
with the lowest ID among the rest controllers.
In multiple mode, the OpenFlow switch simultaneously connects to all controllers. If one or more
controllers become invalid or disconnected, the OpenFlow switch continues to exchange messages
with the rest of the controllers.
Examples
# Set all controllers of OpenFlow instance 1 to operate in single mode.
<Sysname> system-view
[Sysname] openflow instance 1
[Sysname-of-inst-1] controller mode single
datapath-id
Use datapath-id to set the datapath ID for an OpenFlow instance.
Use undo datapath-id to restore the default.
Syntax
datapath-id id
undo datapath-id
Default
The datapath ID of an OpenFlow instance contains the instance ID and the bridge MAC address of
the device. The lower 16 bits are the instance ID and the upper 48 bits are the bridge MAC address
of the device.
Views
OpenFlow instance view
Predefined user roles
network-admin
Parameters
id: Specifies the datapath ID for the OpenFlow instance, in the range of1 to ffffffffffffffff in hexadecimal
format.
Examples
# Set the datapath ID to 123456 for OpenFlow instance 1.
<Sysname> system-view

7
[Sysname] openflow instance 1
[Sysname-of-inst-1] datapath-id 123456
default table-miss permit
Use default table-miss permit to change the default action of table-miss flow entries to forward
packets to the normal pipeline.
Use undo default table-miss permit to restore the default.
Syntax
default table-miss permit
undo default table-miss permit
Default
The default action of a table-miss flow entry is to drop packets.
Views
OpenFlow instance view
Predefined user roles
network-admin
Usage guidelines
Packets that do not match the MAC-IP flow entries are matched with ARP or MAC entries before
table-miss flow entries. If a match is found, the packets are forwarded in the normal forwarding
process. If no match is found, the packets are dropped.
Examples
# Configure the default action of table-miss flow entries to forward packets to the normal pipeline.
<Sysname> system-view
[Sysname] openflow instance 1
[Sysname-of-inst-1] default table-miss permit
description
Use description to configure a description for an OpenFlow instance.
Use undo description to restore the default.
Syntax
description text
undo description
Default
An OpenFlow instance does not have a description.
Views
OpenFlow instance view
Predefined user roles
network-admin
Parameters
text: Specifies a description, a case-sensitive string of 1 to 255 characters.

8
Examples
# Configure the description as test-desc for OpenFlow instance 1.
<Sysname> system-view
[Sysname] openflow instance 1
[Sysname-of-inst-1] description test-desc
display openflow
Use display openflow to display controller information for an OpenFlow instance.
Syntax
display openflow instance instance-id { controller [ controller-id ] | listened }
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
instance-id: Specifies an OpenFlow instance by its ID in the range of 1 to 4094.
controller-id: Specifies a controller by its ID in the range of 0 to 63. If you do not specify a controller
ID, this command displays information about all controllers for an OpenFlow instance.
listened: Specifies the client that connects to the server that is enabled for the OpenFlow instance.
Examples
# Display controller information for OpenFlow instance 100.
<Sysname> display openflow instance 100 controller
OpenFlow instance ID: 100
Reconnect interval : 60 (s)
Echo interval : 5 (s)
Controller ID : 1
Controller IP address : 192.168.49.49
Controller port : 6633
Local IP address : 192.0.0.1
Local port : 5566
Controller role : Equal
Connect type : TCP
Connect state : Established
Packets sent : 9
Packets received : 9
SSL policy : --
VRF name : --
Table 1 Command output
Field
Description
Reconnect interval Reconnection interval (in seconds) for an OpenFlow instance to reconnect to
all controllers.

9
Field
Description
Echo interval Connection detection interval (in seconds) at which an OpenFlow instance
sends an echo request message to all controllers.
Controller IP address IP address of the controller.
Controller port TCP port number of the controller.
Local IP address Source IP address of the controller that is connected to the OpenFlow
instance.
Local port Source TCP port number of the current controller.
Controller role
Role of the controller:
•Equal—The controller has the same mode as other controllers that are
specified for the OpenFlow instance.
•Master—The controller is the master controller for the OpenFlow
instance.
•Slave—The controller is a subordinate controller for the OpenFlow
instance.
If the controller is not configured with any role, this field displays two hyphens
(--).
Connect type Type of the connection between the OpenFlow instance and the controller:
TCP or SSL.
Connect state State of the connection between the OpenFlow instance and the controller:
Idle or Established.
Packets sent Number of packets that have been sent to the controller.
Packets received Number of packets that have been received from the controller.
SSL policy Name of the SSL client policy used for SSL connections.
If no SSL client policy is configured, this field displays two hyphens (--).
VRF name Name of the MPLS L3VPN to which the controller belongs.
If no MPLS L3VPN instance is configured, this field displays two hyphens (--).
display openflow auxiliary
Use display openflow auxiliary to display auxiliary connection information and statistics about
received and sent packets for an OpenFlow instance.
Syntax
display openflow instance instance-id auxiliary [ controller-id [ auxiliary auxiliary-id ] ]
Views
Any view
Predefined user roles
network-admin
network-operator
Parameters
instance-id: Specifies an OpenFlow instance by its ID in the range of 1 to 4094.
controller-id: Specifies a controller by its ID in the range of 0 to 63.
auxiliary auxiliary-id: Specifies an auxiliary connection by its ID in the range of 1 to 255.

10
Examples
# Display auxiliary connection information for OpenFlow instance 100.
<Sysname> display openflow instance 100 auxiliary
Controller ID: 1 Auxiliary connection number: 2
Auxiliary connection ID : 1
Controller IP address : 192.168.49.48
Controller port : 6633
Connect type : TCP
Connect state : Established
Packets sent : 9
Packets received : 9
SSL policy : --
Auxiliary connection ID : 2
Controller IP address : 192.168.49.49
Controller port : 6633
Connect type : TCP
Connect state : Established
Packets sent : 9
Packets received : 9
SSL policy : --
Table 2 Command output
Field
Description
Auxiliary connection
number Total number of auxiliary connections.
Auxiliary connection ID ID of an auxiliary connection.
Controller IP address IP address of the controller.
Controller port TCP port number of the controller.
Connect type Type of the connection between the OpenFlow instance and the controller:
TCP UDP, or SSL.
Connect state State of the connection between the OpenFlow instance and the controller:
Idle or Established.
Packets sent Number of packets that have been sent to the controller.
Packets received Number of packets that have been received from the controller.
SSL policy Name of the SSL client policy used for SSL connections.
If no SSL client policy is configured, this field displays two hyphens (--).
display openflow flow-table
Use display openflow flow-table to display flow table information for an OpenFlow instance.
Syntax
display openflow instance instance-id flow-table [ table-id ]
Views
Any view

11
Predefined user roles
network-admin
network-operator
Parameters
instance-id: Specifies an OpenFlow instance by its ID in the range of 1 to 4094.
table-id: Specifies a flow table by its ID in the range of 0 to 254. If you do not specify a flow table ID,
the command displays information about all flow tables for the specified OpenFlow instance.
Examples
# Display information about all flow tables for OpenFlow instance 100.
<Sysname> display openflow instance 100 flow-table
Instance 100 flow table information:
Table 0 information:
Table type: MAC-IP, flow entry count: 1, total flow entry count: 2
MissRule (default) flow entry information:
cookie: 0x0, priority: 0, hard time: 0, idle time: 0, flags: reset_counts
|no_pkt_counts|no_byte_counts, byte count: --, packet count: --
Match information: any
Instruction information:
Write actions:
Drop
Flow entry rule 1 information:
cookie: 0x0, priority: 1, hard time: 0, idle time: 0, flags: none,
byte count: --, packet count: --
Match information:
Ethernet destination MAC address: 0000-0000-0001
Ethernet destination MAC address mask: ffff-ffff-ffff
VLAN ID: 100, mask: 0xfff
Instruction information:
Write actions:
Output interface: HGE1/0/4
Write metadata/mask: 0x0000000000000001/0xffffffffffffffff
Goto table: 1
Table 1 information:
Table type: Extensibility, flow entry count: 2, total flow entry count: 2
MissRule (default) flow entry information:
cookie: 0x0, priority: 0, hard time: 0, idle time: 0, flags: none,
byte count: 300, packet count: 60
Match information: any
Instruction information:
Write actions:
Drop

12
Flow entry rule 1 information: (Not effective)
cookie: 0x0, priority: 0, hard time: 0, idle time: 0, flags: flow_send_rem
|check_overlap, byte count: 8, packet count: 1
Match information:
Input interface: HGE1/0/3
Ethernet source MAC address: 0000-0000-0001
Ethernet source MAC address mask: ffff-ffff-ffff
Instruction information:
Set meter: 100
Apply actions:
Output interface: HGE1/0/4
Write actions:
Output interface: Controller, send length: 128 bytes
Table 3 Command output
Field
Description
Table information Information about the flow table.
Table type Type of the flow table: MAC-IP or Extensibility.
flow entry count Number of flow entries deployed by the controller.
total flow entry count Total number of flow entries in the table.
Flow entry rule information Information about the flow entry. If the flow entry does not take effect, this field
displays Not effective.
cookie Cookie ID of the flow entry.
priority Priority of the flow entry. The larger the value, the higher the priority.
hard time Hard timeout of the flow entry, in seconds. The flow entry is removed when the
timer times out, whether or not the flow entry matches any data stream.
If the flow entry has no hard timeout, the field displays 0.
idle time Idle timeout of the flow entry, in seconds. The flow entry is removed if the flow
entry does not match any data stream during the idle time.
If the flow entry has no idle timeout, the field displays 0.
flags
Flags that the flow entry includes:
•flow_send_rem—Sends a flow removed message when the flow entry is
removed or expires.
•check_overlap—Checks for overlapping flow entries.
•reset_counts—Resets flow table counters.
•no_pkt_counts—Does not count packets.
•no_byte_counts—Does not count bytes.
If the flow entry does not include any flags, this field displays none.
byte count Number of bytes that have matched the flow entry.
packet count Number of packets that have matched the flow entry.
Match information Contents of the match field of the flow entry (see Table 4).

13
Field
Description
Instruction information
Contents of the instruction set of the flow entry:
•Set meter—Sends the matched packet to a specific meter.
•Write metadata—Writes the value into the metadata fields of the
matched packet. Metadata is used for passing messages between flow
tables.
•Write metadata mask—Specifies which bits of the metadata should be
modified.
•Goto table—Sends the matched packet to the next flow table for
processing.
•Clear actions—Immediately clears all actions in the action set.
•Apply actions—Immediately applies specified actions in the action set.
•Write actions—Writes specified actions into the current action set.
For more information about actions, see Table 5.
Table 4 Match field types
Field
Mask field
Description
Input interface N/A Ingress port (see Table 6).
Physical input interface N/A Ingress physical port.
Metadata Metadata mask Metadata and mask.
Ethernet destination
MAC address Ethernet destination MAC address mask Ethernet destination MAC address and mask.
Ethernet source MAC
address Ethernet source MAC address mask Ethernet source MAC address and mask.
Ethernet type N/A Ethernet type of the OpenFlow packet payload.
VLAN ID Mask VLAN ID and mask.
VLAN PCP N/A VLAN priority.
IP DSCP N/A Differentiated Services Code Point (DSCP)
value.
IP ECN N/A Explicit Congestion Notification (ECN) value in
the IP header.
IP protocol N/A IPv4 or IPv6 protocol number.
IPv4 source address Mask IPv4 source address and mask.
IPv4 destination address Mask IPv4 destination address and mask.
TCP source port Mask TCP source port and mask.
TCP destination port Mask TCP destination port and mask.
UDP source port Mask UDP source port and mask.
UDP destination port Mask UDP destination port and mask.
ICMPv4 type N/A ICMPv4 type.
ICMPv4 code N/A ICMPv4 code.
IPv6 source address IPv6 source address mask Source IPv6 address and mask.
IPv6 destination address IPv6 destination address
mask Destination IPv6 address and mask.
IPv6 flow label Mask IPv6 flow label and mask.

14
Field
Mask field
Description
ICMPv6 type N/A ICMPv6 type.
ICMPv6 code N/A ICMPv6 code.
Output interface N/A Output port.
VRF index N/A VPN index.
Fragment N/A Fragment.
Physical output interface N/A Output physical port.
CVLAN ID Mask CVLAN ID and mask.
Experimenter N/A Extension matching fields. Address ID
represents the unique identifier of an address.
Table 5 Actions
Field
Description
Drop Drops the matched packet. This action is not defined in the OpenFlow
specifications.
Output interface Sends the packet through a specific port. For more information about ports, see
Table 6.
send length
Specifies the max length of bytes to be taken from the packet and sent to the
controller.
This field appears only when the reserved port of the controller type is specified as
the output port.
Group Specifies a group table to process the packet.
Set queue Maps the flow entry to a queue specified by its ID.
Set field Modifies a field of the packet.
Table 6 Ports
Port name
Ingress port
Output port
Description
In port Not supported. Supported. Forwarding the packet out of the ingress
port.
Table Not supported. Supported. Submitting the packet to the first flow table
so that the packet can be processed through
the regular OpenFlow pipeline.
Normal Not supported. Supported. Processing the packet by using the normal
forwarding process.
Flood Not supported. Supported. Flooding the packet.
All Not supported. Supported. Forwarding the packet out of all ports.
Controller Supported. Supported. Sending the packet to the controller.
Local Supported. Supported. Sending the packet to the local CPU.
Any Not supported. Not supported. Special value used in some OpenFlow
commands when you do not specify a port.
port name Supported. Supported. Valid physical or logical port on the switch.