Habitat Becklen BECK-CT-SS19-A User manual

Dimensions
Width - 80cm
BECK-CT-SS19-A
Becklen Mosaic Coffee Table
Height - 38cm
Length -80cm

Safety and Care Advice
Important – Please read these instructions fully before starting assembly
If for any reason you should have
problems with your Habitat product,
please contact the store from which
you purchased it.
Please retain your receipt as proof of
purchase.
If you have any comments or
suggestions regarding this product,
assembly instructions or service
received, please contact the store or
Habitat Head Office via its web site:
www.habitat.co.uk
or write directly to: Habitat Retail Ltd.
489-499 Avebury Boulevard,
Milton Keynes MK9 2NW.
General information
Check you have all the components
and tools listed on the front cover
and page 3.
Remove all fittings from the plastic
bags and separate them into their
groups.
Keep children and animals away
from the work area, small parts
could choke if swallowed.
Make sure you have enough space to
layout the parts before starting.
Do not stand or put weight on the
product, this could cause damage.
Assemble the item as close to its
final position (in the same room) as
possible.
Do not place furniture directly in front
of radiators, fires or any other
source of heat.
Parts of the assembly
will be easier with 2
people.
Assemble on a soft level surface to
avoid damaging the unit or your floor.
We do not
recommend the use
of power drill/ drivers
for inserting screws,
as this could damage
the unit.
Only use hand screwdrivers.
Dispose of all packaging carefully
and responsibly.
Each table top is made by hand and is
slightly different and unique.
This table can be used outside all year
around but should be covered or moved
to a sheltered area during the winter
months to protect its good looks.
If covering please ensure that table is
fully dry first, and that cover
is ventilated.
Do not leave this table standing
in water.
From time to time check that there
are no loose screws on this unit.
Tighten as necessary.
Due to the handmade nature of
this table top and the construction
techniques involved, some cracking
may develop on the underside of the
top. This cracking will not affect the
function or serviceability of the table.
Dust regularly with a clean dry cloth.
Wipe up any spills immediately with a
damp cloth and then dry the surface
with a clean dry duster.
Repeat this procedure for periodic
cleaning.
Remove stubborn stains with a weak
washing up liquid solution and a damp
cloth and dry after with a clean cloth.
The use of furniture polish or spray is
not necessary or recommended.
Never use abrasive or corrosive
cleaning agents.
If paint finish becomes chipped or
damaged treat exposed area with rust
inhibitor immediately and then touch
up with a suitably colour matching
paint for use on metalwork.
General care and maintence
Cleaning and care
Maximum recommended
loading. Do not stand on
the table!
MAX
30kg

Components & Fittings
Please check you have all the components and fittings listed below
If you need help or have damaged or missing parts, email:
customer[email protected] or call: 0344 499 4686
Note: There are ‘Batch Code’ lables where shown on the indicated items, these
should be retained.
1. Top x 1
2. Leg x 4 (lEEE ft + right)
1. Leg support
A
8 x 15mm Bolt + 8 x 18 washers) x 8
B
6 x 10mm nut x 4
C
4mm Hex key x 1
D
10mm spanner x 1
e

Assembly Instructions
Please check you have all the components and fittings listed below
Step 1
Step 2
If you need help or have damaged or missing parts, email:
customer[email protected] or call: 0344 499 4686
Please Note!
Only partially tighten each bolt
until all are in place. Only then
fully tighten each bolt.
Take care to ensure all bolts
are fully tightened before
turning the table upright!
Take care when turning table upright!
2
3
B
D
C
A
3
2
1