Habitat Turned Leg Dining Table AUST- ET-SS20-A User manual

Assembly Instructions - Please keep for future reference
Important - Pleasereadtheseinstructions before assembly
If you need helpor have damaged or missing parts, email:
[e-mail] or call: 03444994686
Dimensions
Turned Leg Dining Table
habitat
Width -2 60 cm
Depth - 9 5cm
Height - 7 6 cm
AUST- E T -SS 20- A
121
1
Ver1

Safety and Care Advice
Important  Please read these instructions fully before starting assembly
Check you have all the components andtools listed
on the front cover and pages 3 -4.
Remove all fittings from the plastic bags and
separate them into their groups.
Keep children and animals away from the work
area, small parts could choke if swallowed.
Make sure you have enough space to layout the
parts before starting.
Do not stand or put weight onthe product,this could
cause damage.
Assemble the item asclose toits final position (in the
same room) as possible.
Do not place furniture directly in front ofradiators,
fi res or any other source of heat.
Parts of the assembly will
be easier with 2 people
Assemble on a soft level surface to avoid damaging
the unit or your floor
We do not recommend the
use of power drildrivers
for inserting screws as
this could
damage the unit. Only use hand screwdrivers.
Dispose of all packaging carefully and responsibly
General care
Take care when moving furniture - dragging it
across the floor will loosen and damage the joints.
Always lift and move
From time to time check that there are no loose
fittings. Tighten as necessary.
Avoid exposing your furniture to direct and
prolonged periods of sunlight and heat sources as
fading and cracking may occur.
Take care to prevent sharp objects e.g. toys,
buckles and heels from coming into contact with
your furniture, and avoid contact with chemicals
e.g. cosmetics or hair products which may
permanently mark the surface.

Cleaning and care Maximumweight limit
Dust regularly with a clean dry cloth.
Wipe up any spills immediately with a damp cloth and
then dry the surface with a clean dry duster.
Repeat this procedure for periodic cleaning.
Remove stubborn stains with a weak washing up
liquid solution and a damp cloth and dry after with a
clean cloth.
The use of furniture polish or spray is not necessary
or recommended.
Never use abrasive or corrosive cleaning agents.
Always use place mats and coasters to protect the
surface from moisture and heat.
ImportantRecommended maximumload for each
shelf is shown below
General information
If for any reason you should have problems with
your Habitat product, please contact the store from
which you purchased it.
Please retain your receipt as proof of purchase
If you have any comments or suggestions regarding
this product, assembly instructions or service
received, please contact the store or Habitat Head
Office via its web site: www.habitat.co.uk
or write directly toHabitat Retail Ltd. 489-499
Avebury Boulevard,
Milton Keynes MK92NW
Max.
8 0 kg
Max.
30 kg
2
Ver1

Components - PanelsIf you need help or have damaged or missing parts, email:
[e-mail] or call 0344 499 4686
Please check you have all the panels listed below
BC Note There are Batch Code labe l swhere shown on the indicated items, these should be retained
BC
11
3
Ver1

Components - Fittings If you need helpor have damaged or missing parts, email:
[e-mail] or call: 03444994686
Please check you have all the panels listed below
Note: The quantities below are the correct amount tocomplete theassembly. Insome cases more fi
ttings may be supplied thanarerequired.
Ruler - To helpcorrectly identify the fi xings
0 10 20 30 40 50 60 70 80 90 100 110 120
Washer x 8
Fittings
Screws x 8
Nut x 4
M8x90
A2A3
A4A5A6
A1
Key x 1 Felt x 4
Nut x 8
M8x24x2,0 M8x6
d12x70 28 mm
4
Ver1

Assembly Instructions
Step 
A14x
x8
Step 
4
44
1. 2.
A4
A1
A1
5
Ver1

Assembly Instructions
Step
3
A3
A28
8AA5

AA6
A2
A2
A5
A3
A6
A6
A6
A6
A3
6
Ver1

Assembly Instructions
Step
4
Step
5
Toextendthetableunlockcatches, lift
and pull eachend of the tableapart.
7
Ver1

Assembly Instructions
Step

Step

At this point remove packaging around leaves.
Remove leaves carefully avoiding extending
mechanism.
Once clear of the table remove remaining packaging.
8
Ver1

Assembly Instructions
Step
8
9
Ver1

Assembly Instructions
Step
9
Removeleaves carefully whenreplacing them
tothe tabletoavoiddamage.
10
Ver1