HACKMOTION HM-G-2-100 User manual

QUICK START GUIDE
1. General information
1. Wrist unit
2. Hand unit
3. Glove attachment
Detailed user manual:
hackmotion.com/user-manual
Support:
[e-mail]
4. Power button
- press once to switch the sensor on
- press and hold (3 seconds) to switch it o
5. Micro USB socket for charging the battery
6. Charging indicator (red - charging and‘o’ when fully charged)
7. Bluetooth connection indicator (blue; ‘on’when connected)
8. Power indicator (yellow)
Golf Sensor HM-G-2-100
(iOS and Windows)
1
3
4
2
56 7 8
3.2.2. Install HackMotion software.
- Download it from: hackmotion.com/downloads
- Launch software installer.
- Accept Windows security warning if prompted (Click ‘More info’
and then ‘Run’) and complete the installation.
2. System requirements
2.1. iOS
- Any device running iOS 11 or later.
2.2. Windows
- At least Windows 10 operating system on your PC. Bluetooth
connection (if your computer does not have a built-in Bluetooth
adapter any Bluetooth USB dongle should do the job).
3. Setting up the system
3.1. iOS
- download HackMotion app from Apple App Store.
3.2. Windows
3.2.1. Pair the sensor
- Make sure your Windows Bluetooth service is enabled.
- Switch the sensor on by pressing the power button. The yellow
LED indicator will light up.
- Pair the device with your PC in Windows Bluetooth settings (has
to be done only once – during initial setup).
Important!
Close Windows
Bluetooth settings
window after the
sensor is paired with
your computer.
There are two ways to wear the hand unit
A. Attaching it to glove velcro
with included clip.
B. Wearing it with palm strap.
Important!
It self xates when stretched
horizontally.
Important!
Pay attention to correct
direction of the clip.

4.5. Calibrate the sensor.
Press‘Calibrate’ icon on the
left side of screen and
follow the instructions. You
can always validate the
calibration by checking live
angle values and 3D model
to see if they correspond
to your hand movements.
4.6. Start hitting shots. The software will automatically detect golf
swings of your chosen training mode, if impact vibration is detected.
- Immediate
Biofeedback for
position training and
slow rehearsals. The
software plays
immediate sound
signal if the parameter
is within your chosen
range.
- After-shot
Biofeedback after each
swing. The software
changes audio tone
depending on
whether the selected
parameter was within
your chosen range
during the selected
position of the swing.
4.7. Set BioFeedback. Press ‘BioFeedback’ icon on the left side of
screen.
5. Troubleshooting
- make sure that the sensor is properly xed to the hand and
doesn't slide/move.
- after switching on the sensor and before calibration make sure
to rotate your hand in random directions in the air for couple of
seconds (this allows the sensors to self correct and settle after
power up);
If swings are not captured or data seems o, do a quick "sanity"
check by making sure if the real-time 3D model and
exion/extension, ulnar/radial data corresponds to what you expect.
- If not, rst rotate the hand in random directions in the air to
allow the sensors to self correct and settle.
- If this doesn't help, do a quick re-calibration.
In case the data still seems o, simply turn o both the sensor and
the app to fully restart the system.
4. Software Quick Start Guide (iOS and Windows)
4.1. Turn the sensor on by pressing the power button. The yellow
LED indicator will light up;
4.2. Launch HackMotion software. Wait until the sensor
automatically connects to your device (this might take up to 30
seconds):
- the blue LED indicator on the sensor lights up;
- the software indicates that the device is connected (bottom
corner of the screen).
4.3. Choose mode
- Full Swing (works for full swing, pitching and chipping);
- Putting (still in beta, Windows only);
- Saved Sessions (view data from previous sessions).
Note (for Windows only):
If the sensor does not connect, check if Bluetooth is activated
on your computer and the device is paired in your computer
Bluetooth settings.
Note (for iOS only):
The sensor will not show up among your iOS Bluetooth
devices, but it will automatically connect when sensor is on
and HackMotion app is open. If the sensor does not connect,
check if Bluetooth is activated.
4.4. Launch new session by pressing‘Session’icon on the left side of
the screen. Make sure that the playing side setting in the session
control menu is correct:
- 'Right-handed' for
playing from
right-handed side
(device on the left
hand);
- 'Left-handed' for
playing from
left-handed side
(device on the right
hand).
6. Battery
Lasts up to 7 hours (fully rechargeable in 2 hours). Use standard
micro USB cable to charge it from your computer.
7. Warranty
HackMotion provides 2 year warranty calculated from the shipping
date.
8. Technical support
[e-mail]
Note:
You can recalibrate the
sensor at any time.
© 2019 HackMotion, Sporta 2, Riga, LV-1013, Latvia, European Union
Important!
Do not use the sensor with gloves containing magnets.
Important!
Make sure that your computer / tablet / phone audio is not muted.