Hafele nagold Nebel INOX 90 User manual

Hafele Nagold Appliances
1
Hafele Article Number (533.87.214)
INSTRUCTION MANUAL
Wall mounted Cooker hood –Nebel INOX 90

Hafele Nagold Appliances
2
CONTENT
1……………………………………….Notice
2……………………………………….Feature
3………………………………………..Installation
4………………………………………..Notice of installation
5………………………………………..Safety Warning
6…………………………………………Speed adjustment
7…………………………………………Maintenance
8…………………………………………Trouble shooting

Hafele Nagold Appliances
3
NOTICE
1. Thank you for choosing our cooker hood. Please read the
instruction manual carefully before use.
2. The installation work must be undertaken by a qualified and
competent fitter.
3. The manufacturer disclaims all liability for any damage or injury
caused as a result of not following instructions for installation
contained in the following text.
The cooker hood is used on 220/240v, 50Hz.

Hafele Nagold Appliances
4
(2)FEATURE
1. The cooker hood uses high quality materials, and is made with a
streamlined design.
2. Equipped with a large power low noise electric motor and centrifugal
leaf, it produces strong suction, low noise, non stick grease filter and
easy to clean.
3. With the isolated low voltage circuit board control, 12vAC input, the
lights are therefore safer.
4. Special wind tunnel construction and oil collector design, free dirt will
be absorbed in a second.
5. Gross weight: 15 KGS
Net weight: 13 KGS

Hafele Nagold Appliances
5
(3) Installation
Installation dimension
3.1 The cooker hood should be placed at a distance
of 65-75cm (26-30inch) from the cooking surface
for the best effect. See Image 1.
3.2 Install the hook on a suitable place once the
installation height is fixed, and keep it in line. The
fixed position of the inside chimney bracket is the
place of chimney. See Image 2.
3.3 Fix the outside chimney bracket on the outside
chimney, and be sure that the inside chimney can
be adjusted the height in it freely as well as fixing
the extensible pipe. Afterwards, install the
extensible pipe and chimney on the cooker hood. See Image 3.
3.4 Put the cooker hood on the hook. See Image 4.
3.5 Adjust the height of the inside chimney to the position of the inside
chimney bracket and fix on it by screw, after adjusting the position, fix the
body with safety screw. See Image 5.

Hafele Nagold Appliances
6
Note: The two safety vents are positioned on the back casing, with diameter of
6mm.
(4) NOTICE OF INSTALLATION
1. Before installation, please ensure the area is clean to avoid suction
of the remaining bits of broken wood and dust.
2. It cannot share the same air ventilation tube with other appliance
such as gas tube, warmer tube, and hot wind tube.
3. The bending of ventilation tube should be≥120°, parallel or above
the start point and should be connected to the external wall.
4. After installation, make sure that the extractor is level to avoid
grease collection at one end.

Hafele Nagold Appliances
7
(5) SAFETY WARNING
Keep your children from using the cooker hood.
Your cooker hood is for domestic use only, not suitable for barbecue, roast
shop and other commercial use.
Any installation work must be carried out by a qualified electrician or
competent person.
The cooker hood and its filter mesh should be cleaned regularly in order to
keep in good working order.
Before cleaning, always ensure that you have switched your cooker hood
off.
Clean the cooker hood according to the instruction manual and keep the
cooker hood from the danger of burning.
No fire for drying your cooker hood.
If there is any fault with your cooker hood, please call the service
department appointed by agent for servicing.
Please keep the room draughty when your cooker hood and gas hob are
working.
Do not exhaust the gas from cooker hood through the same heated flue
which is for the gas from gas hob and other kitchen appliances.
Before installation and usage, read all the instructions and make sure that
the voltage (V) and the frequency (Hz) indicated on your cooker hood are
exactly the same as the voltage (V) and the frequency (Hz) in your home.
In order to get the most out of your cooker hood, please read the
instruction manual before installing & using, and keep it in a safe place.
Ensure that you could get our guarantee for your cooker hood, please
provide the warranty card and purchase receipt, or the guarantee will not
be offered.

Hafele Nagold Appliances
8
（6）Speed adjustment
Push button
1. Push stop button, and the motor will stop.
2. Push the Low button, the buzzer will buzz once, and the motor runs at
low speed.
3. Push the Mid button, the buzzer will buzz once, and the motor runs at
mid speed.
4. Push the High button, the buzzer will buzz once, and the motor runs at
high speed.
5. Push the light button and the two lights will come on. Push it again and
the light will turn off.

Hafele Nagold Appliances
9
(7) MAINTENANCE
7.1 The cleaning of the carbon grease filter mesh
The filter mesh is made of high-density stainless steel. Please do not use
the corrosive detergent on it. Keeping this filter clean will keep the
appliance running correctly. Please strictly follow the guidelines below.
Method 1: Put the mesh into 40-50 c clean water, pour on detergent, and
soak for 2-3 mins. Wear gloves and clean with a soft brush. Please do not
apply too much pressure, as the mesh is delicate and will damage easy.
Method 2: If instructed to do so, it can be put into a dishwasher, set the
temperature at around 60 degrees.
7.2 Notice of cleaning cooker hood
A. To protect the main body from corrosion over a long period of
time, the cooker hood should be cleaned with hot water plus non
corrosive detergent every two months.
B. Please do not use abrasive detergent for it will damage the body.
C. Keep the motor and other spare parts free from water, as this will
cause damage to the appliance.
D. Before cleaning the appliance please remember to cut off power
E. The carbon filter shouldn’t be exposed to heat.
F. Please don’t tear open the fixed bar around the carbon filter
G. If the plug or cord is damaged, please replace it with special soft
cord.

Hafele Nagold Appliances
10
8. Troubleshooting
Fault
Cause
Solution
Light on, but motor
does not work
The leaf blocked
Get rid of the blocking
The capacitor damaged
Replace capacitor
The motor jammed bearing
damaged
Replace motor
The internal with of motor off or
a bad smell from the motor
Replace motor
Light does not work,
motor does not work
Beside the above mentioned, check the following:
Light damaged
Replace lights
Power cord looses
Connect the wires as per
the electric diagram
Oil leakage
One way valve and the air
ventilation entrance are not
tightly sealed
Take down the one way
valve and seal with glue
Leakage from the connection of
U-shaped section and cover
Take U-shaped section
down and seal with soap or
paint
Shake of the body
The leaf damaged and causes
shaking
Replace the leaf
The motor is not tightly hanged
Lock the motor tightly
The body is not tightly hanged
Fixed the body tightly
Insufficient suction
The distance between the body
and the gas top too long
Readjust the distance
Too much ventilation from open
doors or windows
Choose a new place and
resemble the machine
The machine inclines
The fixing screw not tight
enough
Tighten the hanging screw
and make it horizontal
The hanging screw not tight
enough
Tighten the hanging screw
and make it horizontal