HAGER WERKEN SPEED LABOLIGHT User manual

SPEED LABOLIGHT®
Instruction Manual

2
Instruction Manual
1. Description of the Device:
Polymerization of any commercial material can be carried out with the universal light polymerization
device Speed Labolight. Overheating in case of long term operation is prevented by a cooling device on
the back of Speed Labolight. The polymerization temperature of 40 °C will not be exceeded. Eight
lamps, arranged around the turntables, as well as a halogen lamp transport the polymerization light to
every spot of the object. These lamps belong to the standard equipment and make emission of ultra-
violet rays and white light possible, thus covering the range of all photo active materials between
320 – 550 nm. The lamps have to be replaced after 1,000 working hours. A meter indicates the total
working time. The control unit on the front desk controls the polymerization time from 1 second to
99 minutes. A continuous acoustic signal (30 seconds) indicates the end of the polymerization process.
2. Installation and Start:
Speed Labolight has to be set up on a plain surface in such a way that the cooling grid on the back does
not obstruct the device. The distance between Speed Labolight and walls or other equipments should
be min. 15 cm in order to guarantee a sufficient ventilation. Remove the cover between the halogen
lamp and the disc. The lamps T 1 (white light) and T8 S (black light) are plugged alternately T1 - T8 -
T1 - T8, etc. (s. picture 1). Use the halogen lamp according to picture 2. Put the refractory disc in the
special ring onto the turntable. First, connect the safety plug of the feed line to the device, then plug it
in. Adjust the main switch to ”1”.
(1) Main switch
(2) Button START: by pushing it when the device is ON, the polymerization process starts. By pushing
it during the process the cycle starts to a halt.
(3) Button MENU: by pushing it, you can change the process parameters, that is: the time (in minutes)
of the polymerization process, the time of the final cooling, the possibility to perform a polymeri-
zation process either with or without the HALOGEN LAMP.
(4) These buttons are used to modify the values during the polymerization process setting.
(5) Display LCD
51 2 3 4

3
3.aPutting into Operation:
 • Adjustmainswitchtoposition1(on).
 • Openthedevicebyliftingthedoor.
 • Placetheobjecttobepolymerizedontotheturntable.Ifnecessary,usespecialholder.Makesure
that the object is set up vertically near the lamps.
 • Closethedoor.
 • Pushbutton3(MENU)andselect:
1: the polymerization time in minutes. To modify the selected value, push buttons 4. When the
chosen value is visualized, push button 3 (MENU) again to confirm and move on to the follow-
ing phase.
2: the final cooling time in minutes – the length of time the cooling fan should stay on at the end
of the process (minimum 1 minute). Select the desired time with buttons 4 and push button 3
(MENU) again to confirm and move on to the following phase.
3: if you want to select a process with or without the HALOGEN lamp. (1=NO , 2=YES to move
from 1 to 2 use buttons 4). Push button 3 (MENU) again to exit programming.
At this point, the device is ready to perform the polymerization process.
 • Pressbutton2(START).
 • Makesuretheobjectdoesnotcomeintocontactwiththelampgroup.
 • Waitfortheendofthepolymerizationprocessandalsoforfinalpre-setcoolingtime.
 • Openthedoorandremovetheobject.
 • Incaseyouneedtoremovetheobjectduringthepolymerizationprocess,pressbutton2(START)
and open the door manually.
 • Ifthedoorisopenedduringapolymerizationprocesswithoutfollowingtheaboveinstructions,
the process will come to a halt, but the device will execute the final pre-set cooling time.
3.bLanguage setting:
Press the “-” button and switch on the unit. The display shows the pre-set language. The language
can be changed by pressing the “-” button until the required language shows up. Choose between
German, Italian, English and French.

4
4. The Lifetime of the Lamps and Replacement
1. The lifetime of the lamps is about 1,000 working hours. The device is provided with a time meter,
which calculates and adds the hours and minutes of work. To visualize the time meter and to check
the total of working hours, proceed as follows:
 • Switchoffthedevice
 • Switchonthedevice,keepingthe“+”buttonpushed:thetotalamountoftheworkingtimeofthe
lamps will appear (in hours and minutes) on the display.
 • Switchoffthedevicebeforeperformingnewprocesses.
2. When the lamps have reached the lifetime of 1,000 working hours, they must be replaced. After
having replaced them, the time meter must be re-set, proceed as follows:
 • Switchoffthedevice.
 • Pressthe“+”and“-”buttonsandswitchonthedevice(thetotaloperatingtimeisshown).
 • Holdthe“+”and“-”buttonsuntilazeroappears.Thiswilltakeabout30seconds.
 • Switchoffthedeviceagain.
5. Maintenance and Service:
The current supply has to be interrupted prior to each maintenance. The cleanliness of the lamps has
to be checked regularly. Replace the fuse according to picture 3. In case of technical defects, please
contact your dental dealer or Hager & Werken.
6. Warranty:
The producer ensures that the product is free of defects and that it shows all guaranteed features and/
or all characteristics agreed upon. The warranty starts with the day of delivery of the product and is
valid for twelve months. Excluded from the warranty are faults, careless use of the product, connec-
tion to unsuitable power supply, operation with the wrong voltage, acts of God, such as fire, lightning,
humidity, etc. In case of justified complaints the producer has the right to repair, to deliver spare parts
or to decrease the sales price. Cancellation of the sales contract can only be claimed by the customer
after two repairs have been done without success.

5
7. Technical Data:
Current consumption: 225 W
Current supply: 230 V, 50 Hz
Fuse: 1 x 2.5 A
Lamps: 8 x White light:
Osram Dulux S 9 W/71
or optionally:
Philips PLS – 9 W/52
1 x halogen lamp 15 V – 150 W HLX
Measurements: 25 x 29 x 24 cm
8. Spare Parts:
Lampe S 9 W/71 or PLS 9 W/52 Art.-Nr. 901 002 White light
Lampe S9 W/78 or PLS 9 W/10 Art.-Nr. 901 003 Black light
Halogen lamp HLX Art.-Nr. 901 004
Pic. 1 Pic. 2 Pic. 3
4 x Black light:
Osram Dulux S 9 W/78
or optionally:
Philips PLS – 9 W/10

6
9. Examples for Polymerization Time:
Polymerization times for Vita VM LC:
In order to achieve hardening appropriate for the material involved, the object to be polymerized
on the 40 mm special rings on the slide has to be placed in the center of the turntable within the
light cone of the halogen lamp. Make sure combined dentures with a plaster model get polyme-
rized from all sides and do not exceed the turntable’s inner radius of 6 cm.
Once a layer thickness of 2 mm has been obtained, a final polymerization has to be carried
out.
PRE OPAQUE
OPAQUE
PASTE
Polymeri-
zation
OPAQUE
powder
Interimpoly-
merization
up to max.
1,5 mm
(fixing)
Final poly-
merization
and pontic of
max. 2 mm
Note
3 minutes 5 minutes 5 minutes 10 minutes Main energy source is the halo-
gen lamp in the device, it must
not be switched off.
Re-expose shade areas!
Lamps:
8 x Osram Dulux S 9W/71
1 x Halogen Osram
HLX 15V / 150W

7
Polymerization times for SOLIDEX:
In order to achieve a hardening time meeting the requirements of the material, the object to be poly-
merized on the 40 mm special rings has to be placed on the small object carrier in the center of the
turntable. For combination works with plaster models, please verify that polymerization carried out
from all sides and that the 6 cm inner radius of the rotary disc is not exceeded.
Polymerization times for LICUPLAST:
In order to achieve a hardening time meeting the requirements of the material, the object to be poly-
merized on the 40 mm special rings has to be placed on the small object carrier in the center of the
turntable.
NOTE! When working with SOLIDEX and LICUPLAST, the SPEED LABOLIGHT has to be
equipped with 8 Oxram Dulux S 9W/71 lamps and 1 Osram HLX 15V/150W lamp.
Material Thickness of Layer (mm) Speed Labolight (min.)
SHOFU Solidex „Opaque Paste“ ≤ 0,15 approx. 8 - 10
SHOFU Solidex „Base Paste“ ≤ 2 approx. 3
SHOFU Solidex „Cervical Paste“ ≤ 1 approx. 3
SHOFU Solidex „Body Paste“ ≤ 2 approx. 3
SHOFU Solidex „Enamel Paste“ ≤ 2 approx. 3
SHOFU Solidex „Translucent Paste“ ≤ 2 approx. 3
SHOFU Solidex „Effect Paste“ ≤ 2 approx. 3
SHOFU Solidex „Stains“ ≤ 0,15 approx. 3
SHOFU Solidex „Stain color“ approx. 7
SHOFU Solidex „Endpolymerisation“ approx. 8 - 10
Material Thickness of Layer (mm) Speed Labolight (min.)
LICUPLAST Opaker ≤ 0,2 approx. 5
LICUPLAST Basic Masses up to max. 5,0 approx. 5
LICUPLAST Cervical Masses
Interim Polymerization (Fixing)
Tempering (Final Polymerization)
up to max. 1
> 2
up to max. 2
approx. 3
approx. 5
approx. 5
LICUPLAST dentine, transpa and
gingival masses
Interim Polymerization (Fixing)
Tempering (Final Polymerization)
up to max. 1,5
> 2,5
up to max. 2,5
approx. 3
approx. 5
approx. 1
LICUPLAST Stain Colors ≤ 0,2 approx. 1

2009011203-04-GB
HAGER & WERKEN GmbH & Co. KG
Ackerstraße 1
47269 Duisburg, Germany
T+49(203)99269-0
F+49(203)299283
www.hagerwerken.de
401 125
As of: September 2017
WEEE-Reg.Nr.: DE 21760541