Provision ISR I2-320A-28 User manual

1080P Pro HD Analog Series
USER MANUAL

1
1080P Pro HD Analog Series
Contents
1) Cautions:
2 ) Product Introduction
2.1 Camera Introduction
2.2 Product Features
3)
Menu Setup
4) Product Installation
5) Technical Specification
4.1 General Notes
4.2 Installation Tools and Information
4.3 Installation Method
4.4 Setting the video output type
4.5
4.7
Setting the Camera
OSD Control
4.6Connection

2 3
1 Cautions:
1. To reduce the risk of electric shock, do not open the
camera or perform internal maintainance by yourself.
Please consult a professional service person if needed.
2. To prevent fire or electrical shock hazard, make sure
that the input voltage, current, polarity and operating
temperature meet the requirements of the camera.
3. Please note the operating temperature and environ-
mental limits of the camera. Do not install in higher/low-
er temperatures than -20°C~+50°C (-4°F~122°F).
These cameras are not waterproof! Minimize dust and
moisture erosion, otherwise camera would be damaged.
4. Avoid directing the camera to sunlight while powered
on, otherwise the sensor will be damaged.
5. Do not touch the sensor surface. If any foreign objects
exists use a cotton swab or lens paper to clean. if it is
difficult to remove, use a neutral detergent diluted with
water.
6. In order to ensure smooth and satisfactory image,
the power and video cables shouldn’t be too long.
Please follow general AHD/Analog sepcifications for
cables types and lenghts.
7. In order to prevent the camera from falling, please
install the camera on a stable surface.
8. The camera should not be placed near a radiator or
heating resistor.

4 5
2 Product Introduction
2.1 Camera Introduction
PROVISION-ISR’s new series of cameras have
adopted a high performance CMOS image sensor
which provides HD resolution and supports high
resolution video output. The cameras support video
transmission distance of around 400M base on Rg59
standard coaxial cable. This series can support AHD/
TVI/CVI/CVBS 960H analog output.
2.2 Product Features
● Coaxial Cable with BNC Connector
● DIP Switch
● Auto Day/Night (ICR)
● BLC / HLC
● 2D/3D NR
● AHD/TVI/CVI/CVBS Signal Selectable (by jumper)
3 Menu Setup
AHD/TVI: Click on “Iris+” button from the DVR’s PTZ
interface to call the OSD Menu. Use the PTZ interface to
scroll through the menu and “Iris+” to confirm.
CVI: Click “
►” button from the DVR’s PTZ interface, then
click “ ” and press “Enter” to call the OSD Menu.
4 Product Installation
4.1 General Notes
1. Make sure the unit is powered off before installation.
2. Check that power supply voltage complies with the
camera requirement to prevent damage to the camera.
3. The installation and maintenance of this product
should be done by a professional. Please do not remove
or modify the camera in any way.

6 7
4.2 Installation Tools and Information:
Prepare the required tools and instructions. Before
installation please prepare the following tools:
A straight or a Phillips-head screwdriver, multi-meter,
cutter, needle nose pliers, measuring tape, pencil.
4.3 Installation Method:
1. Check the camera for any external damage.
2. Mount the bracket or base:
① For cement wall, install the expansion screws, and
then mount the bracket/base.
② For wooden wall use self-tapping screws to mount.
4.4 Setting the video output type:
The camera supports AHD/TVI/CVI/CBVS video output,
And PAL/NTSC system is switable by setting a DIP
switch on the cable as illustrated:
The Default Setting is PAL + AHD
4.5. Setting the camera:
a. Dome Camera
Adjust the lens position so it aims at the main monitoring
point and gives a clear picture.
b. Bullet Camera
Adjust the body so that the lens aims at the main
monitoring point and gives a clear picture. Tighten the
screws to ensure that it does not move.
Note:
The wall needs to bear at least 3
times the weight of the camera.

8 9
4.6 Connection
Connection as shown in the figure below:
4.7 OSD Control
The OSD control is available by CoC (Control over
Coax). If your AHD/TVI/CVI DVR supports this
function*, use the DVR’s PTZ interface to press on
“Iris+” or “ ” to open the OSD menu.
Navigate through the OSD menu using the PTZ
direction arrows.
* Notice: CoC function works no more than 200M by Rg59 coaxial cable
* All of Provision-ISR’s DVRs support CoC Starting from version 3.4.4
4.8 OSD Menu Scheme:
Main Menu Second Menu Third Menu
Brightness 0~100
Global / Center / BLC / FLC
ATW
Red Gain
Blue Gain
0~100
EXT
Color
B&W
Contrast
Sharpness
Manual
Auto
AE
AWB Manuel
Grey Mode
Day / Night
Image Enhance
DC
Manual
Auto
Auto
Saturate
Manual
Auto
3DNR
Manual
Auto
2DNR
Manual

10 11
5 Specifications:
2MP Pro HD Analog Series
Model
Image Sensor
Image Format
Effective Pixels
Scanning System
Resolution
FPS
Min. Illumination
D&N
IR LED
OSD Menu
CoC Support
Day & Night Mode
Backlight Compensation
S/N Ratio
White Balance
Noise Reduction
Video Output
Privacy Mask
D-Effect
WDR
Lens (Field Of View)
Power
Operation Temperature
Protection Rate
Dimensions
Net Weight
1/2.9" 2MP Sensor
16:9
1936x1096
Progressive
2MP: 1920x1080 AHD/TVI/CVI
1MP: 1280x720 AHD/TVI/CVI
CVBS: 700TVL
25/30FPS
Color: 0.005lux @F1.2, AGC ON B/W: 0lux with IR
True Day&Night-ICR
Available via CoC Only
Yes
Ext/Auto/Day/Night
No
≥52dB (AGC OFF)
Auto / Manual
3D-DNR
2MP / 1MP (Selected by OSD Menu)
AHD/TVI/CVI/CVBS + PAL/NTSC (Selected by DIP Switch)"
No
No
No
-30°C ~ 50°C, 10% ~ 90% humidity
IP67
I2-320A-28
1LED Array (20m)
2.8mm Fixed (88°)
DC12V/320mA
172.2*73.4*74.5mm
475g
I4-320A-VF
3LED Array (40m)
2.8-12mm VF (88°-33°)
DC12V/560mA
220.8*79.4*81.2mm
700g
Main Menu Second Menu Third Menu
HD AHD / CVI / TVI / CVBS
1080P@25 / 1080P@30
720P@25 / 720P@30
PAL/NTSC (For CVBS)
English
Video Settings
Language
Chinese
Reset
Standard
I4-320A-28
2LED Array (40m)
2.8mm Fixed (88°)
DC12V/470mA
220.8*79.4*81.2mm
645g

12 13
12 13
Model
Image Sensor
Image Format
Effective Pixels
Scanning System
Resolution
FPS
Min. Illumination
D&N
IR LED
OSD Menu
CoC Support
Day & Night Mode
Backlight Compensation
S/N Ratio
White Balance
Noise Reduction
Video Output
Privacy Mask
D-Effect
WDR
Lens (Field Of View)
Power
Operation Temperature
Protection Rate
Dimensions
Net Weight
1/2.9" 2MP Sensor
16:9
1936x1096
Progressive
2MP: 1920x1080 AHD/TVI/CVI
1MP: 1280x720 AHD/TVI/CVI
CVBS: 700TVL
25/30FPS
Color: 0.005lux @F1.2, AGC ON B/W: 0lux with IR
True Day&Night-ICR
Available via CoC Only
Yes
Ext/Auto/Day/Night
No
≥52dB (AGC OFF)
Auto / Manual
3D-DNR
2MP / 1MP (Selected by OSD Menu)
AHD/TVI/CVI/CVBS + PAL/NTSC (Selected by DIP Switch)"
No
No
No
-30°C ~ 50°C, 10% ~ 90% humidity
IP67
DI-320A-28
1LED Array (20m)
2.8mm Fixed (88°)
DC12V/270mA
Φ97*82.6mm
485g
DI-320A-VF
3LED Array (40m)
2.8-12mm VF (84°-32°)
DC12V/660mA
Φ113*99.6mm
695g