Panasonic Super Dynamic III WV-NS202A User manual

Model No. WV-NS202A
ORDER NO. AVS0705901C0
S02
O
LCK
W2
02
S
N
-
VA
E
P
ON
C2007 Matsushita Electric Industrial Co., Ltd.
All rights reserved. Unauthorized copying and
distribution is a violation of law.
Network Camera
SPECIFICATIONS
The Product with PbF
Other specifications
Power source
Power consumption
Ambient temperature
Ambient humidity
Monitor output
External I/O terminals
Microphone input
Audio output
Dimensions
Weight
DC12 V, PoE (IEEE802.3af compliant)
DC 12 V: Approx. 1 A, PoE: Approx. 12 W (Class 0 device)
ー10 ゜C - +50゜C (14 ゜F - 122 ゜F)
Recommended operating temperature: +35 ゜C (95 ゜F)
90 % or less
VBS: 1.0 V [P-P]/75 Ω, composite (BNC),φ3.5 mm mini jack (monaural)
ALARM IN 1, ALARM IN 2/ALARM OUT, ALARM IN 3/AUX OUT (x1 each)
MIC IN (Applicable microphone: Plug-in power type)
Supply voltage: 2.5 V ±0.5 V
Input impedance: 3 kΩ10 %
AUDIO OUT φ3.5 mm stereo mini jack (Monaural output, Line level)
φ115 mm x 154 mm (H) (excluding the DC 12 V power cord plug)
Camera: Approx. 850 g
Accessories (Camera mount bracket, decorative cover): Approx. 200 g

CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Y
IMPORTANT SAFETY NOTICE
YWARNING
LITHIUM BATTERY
WARNING CAUTION
The lithium battery in this equipment must only be
replaced by qualified personnel. When necessary, contact
your local Panasonic supplier.
Danger of explosion if battery is incorrectly replaced.
Replace only with the same or equivalent type recom-
mended by the equipment manufacturer. Discard used
batteries according to manufacture's instructions.
This service information is designed for experienced repair technicians only and is not designed for use by the
general public.
It does not contain warnings or cautions to advise non-technical individuals of potential dangers in attempting to
service a product.
Products powered by electricity should be serviced or repaired only by experienced professional technicians. Any
attempt to service or repair the product or products dealt with in this service information by anyone else could
result in serious injury or death.
This symbol warns the user that uninsulated voltage within
the unit may have sufficient magnitude to cause electric
shock. Therefore, it is dangerous to make any kind of contact
with any inside part of this unit.
This symbol alerts the user that important literature concerning
the operation and maintenance of this has been included.
Therefore, it should be read carefully in order to avoid
any problems.
CAUTION:
TO REDUCE THE RISK OF ELECTRIC SHOCK,
DO NOT REMOVE COVER (OR BACK). NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
Distribution of PbF PCB:
PCBs (manufactured) using lead free solder (PbF) will have a stamp on the PCB.
Caution:
Lead free solder has a higher melting point than standard solder. Typically the melting points is 35 °C – 40 °C
(95 °F – 104 °F) higher. Please use a soldering iron with temperature control and adjust it to 360 °C – 370 °C
(680 °F – 698 °F). In case of using high temperature soldering iron, please be careful not to heat too long.
Lead free solder will tend to splash when heated too high (600 °C / 1112 °F).
Lead free solder (Sn - 3.0Ag – 0.5Cu) or equivalents are recommended on repairing our lead free soldered PCB.
About Lead Free Solder (PbF)
There are special components used in this equipment which are important for safety. These parts are indicated
by the ” ” mark on the schematic diagram and the replacement parts list. It is essential that these critical
parts should be replaced with manufacturer's specified parts to prevent X-radiation, shock, fire, or other hazards.
Do not modify the original design without permission of manufacture.

CAMERA
Image sensor 1/4 inch interline transfer CCD
Effective pixels 768 (H) x 494 (V)
Scanning area 3.59 mm (H) x 2.70 mm (V)
Scanning system 2:1 interlace scan (with motion adaptive interlace/progressive conversion function)
Minimum illumination Color(Colour): 0.7 lx (Sensitivity up: OFF, AGC: HIGH)
Simple Black & white mode OFF/AUTO
Simple black and white: 0.5 lx (Sensitivity up: OFF, AGC: HIGH)
Dynamic range 52 dB typ. (Super dynamic 3: ON, Shutter speed: OFF)
Gain ON (LOW)/ON (MID)/ON (HIGH)/OFF
Shutter speed OFF (1/60), AUTO, 1/100
Sensitivity up Up to 32x
White balance ATW1/ATW2/AWC
Digital Noise Reduction (DNR) LOW/HIGH
Electronic Zoom Up to 10x
Camera title Up to 16 characters (alphanumeric characters, marks) ON/OFF
VMD alarm ON/OFF, 4 areas available per preset position
Image hold ON/OFF
Privacy zone ON/OFF (up to 8 zones available)
UP side down ON (desktop)/OFF (ceiling)
LENS
Zoom ratio 22x
Focal length 3.79 mm – 83.4 mm
Maximum aperture ratio 1 : 1.6 (WIDE) – 3.0 (TELE)
Macro 1.6 m
Aperture range F1.6 – 22, Close
Horizontal angle of view 2.6 ° (TELE) – 51.7 ° (WIDE)
Vertical angle of view 2.0 ° (TELE) – 39.9 ° (WIDE)
Panning/tilting platform
Panning range 0 ° - 350 °
Panning speed Manual: Approx. 1 °/s - 100 °/s, preset: up to approx. 300 °/s
Tilting range –30 ° - 90 ° (upward – level – downward)
Selectable tilting angle: 0 °/–5 °/–10 °/–15 °/–20 °/–25 °/–30 °
Tilting speed MANUAL Approx. 1 °/s - 100 °/s, preset: up to approx. 100 °/s
Number of the preset positions 64
Auto mode OFF/preset sequence/auto pan/auto track
Self return 10 s/20 s/30 s/1 m/2 m/3 m/5 m/10 m/20 m/30 m/60 m
Map shot 360 ° map shot/preset map shot
Network
Network 10BASE-T/100BASE-TX, RJ45 connector
Resolution VGA (640 x 480)/QVGA (320 x 240)
Image compression method
MPEG-4 Image quality: LOW/NORMAL/FINE
Transmission type: UNICAST/MULTICAST
JPEG Image quality: 0 SUPER FINE/1 FINE/2/3/4/5 NORMAL/6/7/8/9 LOW (10 steps: 0-9)
Transmission type: PULL/PUSH
Refresh interval (MPEG-4) 0.1 fps – 30 fps (Frame rate of JPEG display will be limited when displaying JPEG and MPEG-4
simultaneously.)
Audio compression method G.726 (ADPCM) 32 kbps/16 kbps
Bandwidth Control 64 kbps/128 kbps/256 kbps/512 kbps/1 024 kbps/2 048 kbps/4 096 kbps/Unlimited
Protocol TCP/IP, UDP/IP, HTTP, RTP, FTP, SMTP, DHCP, DNS, DDNS, NTP, SNMP
OS Microsoft Windows 2000 Professional SP4, Microsoft Windows XP Home Edition SP2, Microsoft
Windows XP Professional SP2,
Web browser Microsoft Internet Explorer 6.0SP2, Microsoft Internet Explorer 7.0 (Microsoft Internet Explorer
6.0 SP1 only when using Windows 2000 Professional SP4)
Maximum concurrent
access number 8 (Depends on network conditions)
FTP client Alarm image transmission, FTP periodic transmission
Multi-screen Images from 16 cameras (4 cameras x 4 groups) can be displayed simultaneously.
SD memory card (option) Manufactured by Panasonic (Performance with this camera has been checked.)
Capacity: 64 MB, 128 MB, 256 MB, 512 MB, 1 GB, 2 GB
* SD High Capacity (SDHC) card is not compatible with this camera.
®® ®® ®
®
®® ® ®
®

STANDARD ACCESSORIES
CD-ROM* .................................................................................................. 1 pc.
Installation Guide ...................................................................................... 1 pc.
Warranty(for NTSC) ................................................................................... 1 pc.
* The CD-ROM contains the operating instructions (PDFs) and the software.
The following are for installation.
Mount bracket (w/safety wire) .................................................................... 1 pc.
Fixing screw ............................................................................................... 2 pcs. (incl. a spare screw)
Decorative cover ........................................................................................ 1 pc.
DC 12 V power cord plug .......................................................................... 1 pc.
Code label* ................................................................................................ 1 pc.
* It will be needed for network management.
A network administrator should keep this label.

DISCLAIMER OF WARRANTY
IN NO EVENT SHALL MATSUSHITA ELECTRIC INDUS-
TRIALCO,.LTD. BE LIABLE TO ANY PARTY OR ANY
PERSON, EXCEPT FOR REPLACEMENT OR REASON-
ABLE MAINTENANCE OF THE PRODUCT, FOR THE
CASES, INCLUDING BUT NOT LIMITED TO BELOW:
(1) ANY DAMAGE AND LOSS, INCLUDING WITHOUT
LIMITATION, DIRECT OR INDIRECT, SPECIAL,
CONSEQUENTIAL OR EXEMPLARY, ARISING OUT
OF OR RELATING TO THE PRODUCT;
(2) PERSONAL INJURY OR ANY DAMAGE CAUSED
BY INAPPROPRIATE USE OR NEGLIGENT OPER-
ATION OF THE USER;
(3) UNAUTHORIZED DISASSEMBLE, REPAIR OR
MODIFICATION OF THE PRODUCT BY THE USER;
(4) INCONVENIENCE OR ANY LOSS ARISING WHEN
IMAGES ARE NOT DISPLAYED, DUE TO ANY
REASON OR CAUSE INCLUDING ANY FAILURE
OR PROBLEM OF THE PRODUCT;
(5) ANY PROBLEM, CONSEQUENTIAL INCONVE-
NIENCE,OR LOSS OR DAMAGE, ARISING OUT
OF THE SYSTEM COMBINED BY THE DEVICES OF
THIRD PARTY;
(6) ANY CLAIM OR ACTION FOR DAMAGES,
BROUGHT BY ANY PERSON OR ORGANIZATION
BEING A PHOTOGENIC SUBJECT, DUE TO VIO-
LATION OF PRIVACY WITH THE RESULT OF THAT
SURVEILLANCE-CAMERA'S PICTURE, INCLUD-
ING SAVED DATA, FOR SOME REASON,
BECOMES PUBLIC OR IS USED FOR THE PUR-
POSE OTHER THAN SURVEILLANCE;
(7) LOSS OF REGISTERED DATA CAUSED BY ANY
FAILURE.
LIMITATION OF LIABILITY
THIS PUBLICATION IS PROVIDED "AS IS" WITHOUT
WARRANTY OF ANY KIND, EITHER EXPRESS OR
IMPLIED, INCLUDING BUT NOT LIMITED TO, THE
IMPLIED WARRANTIES OF MERCHANTABILITY, FIT-
NESS FOR ANY PARTICULAR PURPOSE, OR NON-
INFRINGEMENT OF THE THIRD PARTYÅfS RIGHT.
THIS PUBLICATION COULD INCLUDE TECHNICAL
INACCURACIES OR TYPOGRAPHICAL ERRORS.
CHANGES ARE ADDED TO THE INFORMATION HERE-
IN,AT ANY TIME, FOR THE IMPROVEMENTS OF THIS
PUBLICATION AND/OR THE CORRESPONDING
PRODUCT (S).

CONTENTS
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS ..............................................................................1-1
LIST OF CONSUMPTION PARTS ......................................................................................................................... 2-1
ADJUSTMENT PROCEDURE ............................................................................................................................... 2-1
WIRING DIAGRAM ................................................................................................................................................ 3-1
SCHEMATIC DIAGRAM
SENSOR BOARD .............................................................................................................................................. 4-1
PoE BOARD ....................................................................................................................................................... 4-2
SERVO BOARD ................................................................................................................................................. 4-3
MAIN BOARD (1/2) (CAMERA CPU, DSP PERIPHERAL) ................................................................................ 4-4
MAIN BOARD (2/2) (AF) .................................................................................................................................... 4-5
NETWORK BOARD (1/4) (CPU + DSP PERIPHERAL, SDRAM)...................................................................... 4-6
NETWORK BOARD (2/4) (SETTING SWITCH, ETHERNET, FLASH, EXPANSION OUTPUT) ....................... 4-7
NETWORK BOARD (3/4) (AUDIO, PAN) ........................................................................................................... 4-8
NETWORK BOARD (4/4) (DC 12 V INPUT, DC/DC, ALARM, SD MEMORY CARD, RTC) .............................. 4-9
CONDUCTOR VIEW
SENSOR BOARD ...............................................................................................................................................5-1
PoE BOARD (COMPONENT SIDE)....................................................................................................................5-2
PoE BOARD (PATTERN SIDE) ...........................................................................................................................5-3
SERVO BOARD ..................................................................................................................................................5-4
MAIN BOARD (COMPONENT SIDE) .................................................................................................................5-5
MAIN BOARD (PATTERN SIDE) ........................................................................................................................5-6
NETWORK BOARD (COMPONENT SIDE)........................................................................................................5-7
NETWORK BOARD (PATTERN SIDE) ...............................................................................................................5-8
EXPLODED VIEW
(1/6) (MAIN UNIT-1) ............................................................................................................................................6-1
(2/6) (MAIN UNIT-2) ............................................................................................................................................6-2
(3/6) (PAN CHASSIS UNIT-1) .............................................................................................................................6-3
(4/6) (PAN CHASSIS UNIT-2) .............................................................................................................................6-4
(5/6) (CAMERA UNIT) ........................................................................................................................................6-5
(6/6) (PACKAGING).............................................................................................................................................6-6
REPLACEMENT PARTS LIST ...............................................................................................................................7-1

1-1
MAJOR OPERATING CONTROLS AND THEIR FUNCTIONS
Front view
KCOL
WV2
A
02S
N
-
NEPO
FRONT
NEP
O
K
C
O
L
Mount bracket (standard accessory)
WV-NS202A
WV-NS202A
SD memory card slot
SD memory card slot cover
SD memory card error indicator
( Network Operating Instructions)
Panasonic logo plate
Transparent part (over the lens)
Safety wire
(fixed with the mount bracket)
Decorative cover
(standard accessory)

1-2
Rear view
•
MONITOR OUT
AUDIO OUTMIC IN
EXT I/O
4 3 2 1
DC12V IN
POWER
INITIAL
SET
ACT
LINK
10BASE-TX
100BASE-TX
Safety wire holder
Monitor out connector
Audio output connector
Microphone in connector
External I/O terminals
DC 12 V power terminals
Power LED
[INITIAL SET] button
Cable guide
Network connector
Link LED
Access LED
Screw hole for a tripod (1/4-20UNC)
About the [INITIAL SET] button
Turn on the power of the camera while holding down this button, and wait for around 5 seconds without releasing this button. Wait
another 1 minute after releasing the button.The camera will restart and the settings including the network settings will be initialized.
The settings including the network settings will be initialized. Note that the preset position settings will not be initialized.
Important:
Use this hole only when the camera is to be
installed on desktop using a tripod.
Do not use this hole to mount on the ceiling since
the fall prevention measure is unavailable.

1-3
KC
O
L
S
N
-VW A
2
0
2
N
EPO
FRONT
N
EPO
K
C
O
L
WV-NS202A
WV-NS202A

1-4

2-1
LIST OF CONSUMPTION PARTS
REF. NO. PART NAME LIFE
MO1 Tilt Motor Ass'y 3.7 million actions
(20 000 hours )
MO2 Pan Motor Ass'y
FB1 Tilt FPC 3.7 million
FB2 Pan FPC
M43 Lens Ass'y (Focus Motor, Zoom Motor) Each 3.7 million actions
* Lens Motor itself is not supplied, but only
supplied as assembly.
• It changes depending on the actual environment/operating condition.
• Part numbers of these consumption parts are described in Replacement Parts List on page 7-1.

3-1
WIRING DIAGRAM
34
M
Y’
S
S
A
SNE
L
2
O
M
NA
P
R
O
T
O
M
Y
’
SSA
1O
M
TLI
T
R
O
TO
M
Y’SS
A
101L
ETIRREF
EROC
301
L
E
T
I
RR
E
F
E
R
OC
201L
E
TIRREF
ER
OC
21E
1
1
E
C
P
F
N
AP
2
B
F
CPFTLI
T1
BF
5
41
00
5NC
154
4
N
C
3
3
2
3
2
)
1
T
AB(
1
5N
C
1
8
3N
C
13
3
3
07NC
41
7
N
C
14
CN603
401
CN3
81
CN1
401
CN702
119 220
CN2
)205CI(
)
2
K
J
(
)4
NC
(
)2N
C
(
)2
E
()
1
E(
)
4K
J(
)
3K
J
(
)
1KJ
(
)
1WS
(
(CN1)
DRAOBNIAM
DRAOBROSNES
)EDISSISSAHCNAP()EDISAREMAC(
DRAOBEoP
DRAOBOVRES
DR
A
O
B KROWTEN
(PAL,CH)
(PAL,CH)
(PAL,CH)

00
5
Z
105Z
Z502
Q500
L500
L502
L503
L504
L505
45
1
CN500
C502
C510
C516
025C
C522
425C
C525
925C
D500
D501
IC500
105CI
IC503
005SV
405C
I
31
20
1
505CI
10
11
04
20
1
01
11
IC506
PbF
VNS202RB1A
1
8
7
14
1
7
814
IC502
PbF
VNS202RB1A
10
5
L
R539 C530
C603
R506
206C
R504
8
15R
R511
C505
R514R505C500
70
5C
625
R
725C
9
1
5
C
R510C503
C604
C521
R516 R515 R517 C518
R1
C523
C528
C526
C517
TD26
TD505
42DT
3
2DT
12
D
T
21DT
51DT
TD3
TD5
TD4
TD11
TD13
TD16
TD19
TD10
TD9
TD8
TD7
TD6
81DT
TD17
C504
C506
C501
C601
C600
315
C
R502
TD32
TD31
TD14 TD25
TD22
TD533
TD2
TD30
TD28
TD27
TD29
805C
SENSOR BOARD
<INDEX>
SENSOR BOARD
(COMPONENT SIDE)
IC500 A1,A2
IC501 A1
IC503 A2
IC504 A2,B2
IC505 A1
IC506 A2
Q500 A2,B1,B2
D500 OPEN
D501 A1,A2
<INDEX>
SENSOR BOARD
(PATTERN SIDE)
IC502 A1,A2,
B1,B2
(COMPONENT SIDE)
A
B
12
SENSOR BOARD
(PATTERN SIDE)
A
B
12
5-1
CONDUCTOR VIEW OF SENSOR BOARD

D16
51L
R153
331C
4
3
1C
C135
Q3
C137
931C
0
4
1C
C141
T1
8
1
1NC
A1CR202SNV
FbP
201DT
301D
T
TD100
PoE BOARD
<INDEX>
PoE BOARD
(COMPONENT SIDE)
Q3 B3
D16 A2
(COMPONENT SIDE)
A
B
C
123
5-2
CONDUCTOR VIEW OF PoE BOARD (COMPONENT SIDE)

8
1
CI
0
1
Q
1
1Q
2
1Q
D9
01D
D11
21D
D13
003R
D14
5
1D
D18
R136
731R
R138
931R
R140
1
4
1R
241R
R143
R144
R145
R146
R147
R148
941R
R150
2
5
1R
R154
R156
R157
R158
R159
R160
161R
C125
621C
R163
721C
C128
561R
C129
C130
C131
231C
C136
Q6
Q7
8Q
R1
R2
SCR1
18
9
61
71CI
VNS202RC1A
PbF
C1
C123
D8
7D
71L
4R
TD101
501DT
R5
PoE BOARD
<INDEX>
PoE BOARD
(PATTERN SIDE)
IC17 C1
IC18 A1,A2
Q6 B2
Q7 C2
Q8 B1
Q10 A2
Q11 A2
Q12 A1
(PATTERN SIDE)
D7 C1,C2
D8 C1
D9 B2
D10 C2
D11 C2
D12 B1,B2
D13 C2
D14 OPEN
D15 B1,B2
D18 A1
A
B
C
123
5-3
CONDUCTOR VIEW OF PoE BOARD (PATTERN SIDE)

1
4
CN603
226R
R623
C601
C606
C607
C611
316C
D600
106D
L700
IC601
207NC007R
04
1
33
1
CN703
0
07C
C701
207C
C703C704
507C
C706
R550
15
5
R
L600
L601
306L
007CI
PbFVNS202RD1A
A
A
10
11
20
1
006R
1
06
R
R602
R603
406R
R605
606R
R607
806R
R609
R610
R611
R612
R613
R614
516
R
616R 716R
Z700
R618
Z701
R619
736R 936R
006C
C602
C603 C604
C605
C608
C609
C610
C612
616
C
C617
C618
R657
R658
C620
C622
C624
R660
926C
566R
766R
R668
D602
D603
61
8
1
006CI
VS600
IC604
8
1
63
IC609
1
R701
R702
R703
R704
R705
607R
Q600
Q601
206Q
L602
A
VNS202RD1A
PbF
B
B
A
R624
TD713
TD720
TD721
TD704TD716
TD712TD708 TD733
TD707
TD711 TD730
TD723
TD717
TD715
TD705
TD734
TD625
TD736
TD703
TD700 TD719 TD726
TD739
TD735
TD702
TD710
TD718
TD725
TD709
TD706
TD714
TD722
TD729
TD732 TD743
TD731
TD737
TD701
SERVO BOARD
SERVO BOARD
<INDEX>
SERVO BOARD
(COMPONENT SIDE)
IC601 A2,A3
IC700 A1,A3
D600 A2,A3
D601 A2
<INDEX>
SERVO BOARD
(PATTERN SIDE)
IC600 A1,A2
IC604 A1,A3
IC609 A2
Q600 A1
Q601 A2
Q602 A3,B3
D602 A3
D603 OPEN
(COMPONENT SIDE)
(PATTERN SIDE)
A
B
123
A
B
123
5-4
CONDUCTOR VIEW OF SERVO BOARD

C23
206R
352R
0
7
C
2
C
4D
1L
5L
00
6
Z
152
62
05
15
57
67
IC1
2CI
05
26
25 1
3CI
IC9
115C
Q3
Q202
006L
106L
206L
306L
2
1
81
71
1
N
C
19
02
1
2
2NC
04
1
3NC
45 1
CN4
1
X
Z1
Z2
Z3
Z4
Z5
Z6
Z7
8Z
Z9
VNS202RY1A
PbF
1
23
45
7
9
11
12
6
8
51
02
A
B
C
D
E
F
G
H
J
K
LN
R
T
U
V
W
Y
AA
AB
22 2161
84R
442C
08R
R1
R100
R99
R25
R94
C55
R69
R71
C52
R15
R97
R29
R70
R67
R14
C91 C76
C3
C4
R109
R45
R39
R38
R42
1
2R 7
3R 15R 22C
7
01R
0
0
6C
215R
11C
57C
47C 37C
8C03R
96C
8
2R
5C
2
1
R
91R
11R
106C 206C 0
16
C
7C
806R 27C
TD33
TD36
TD35
TD34
TD37
TD122
TD103
TD24
TD5
TD1
TD28 TD27 TD600 TD26
TD13
TD11
TD60
TD8
TD75
005C
C235
C234
C228
R252
C243
TD14
TD104
TD107
TD101
TD112
TD49
TD105
TD46
TD43 TD32
TD40 TD30
35DT
45DT
74DT
15DT
25DT 05DT
44DT
65DT
85DT
55DT
75DT
95DT
IC2
MAIN BOARD
<INDEX>
MAIN BOARD
(COMPONENT SIDE)
IC1 A2,B2
IC2 B1,B2
IC3 A1,A2,
B1,B2
IC9 A2
Q3 B1
Q202 B1
D4 C2
(COMPONENT SIDE)
A
B
C
123
5-5
CONDUCTOR VIEW OF MAIN BOARD (COMPONENT SIDE)

C41
C42
R238
R239
9
5C
642R
742R
002X
C216
C71
C77
87C
X600
X601
C229
C82
C83
C92
1C
C9
1D
952C
2
D3
D
5D
6D
D7
Q500
IC200
20
1
IC203
502CI
5
8
1
4
IC600
106CI
1
0
2
Z
L2
L3
L4
6L
7L
L8
9L
0
1
L
11L
1
4
5
8
5CI
14
5
8
6CI
14
8
7CI
5
41
8
7
1
8CI
1Q
Z10
Z11
3
02
L
L204
R76
406L
R87
R88
X4
51C
61C
7
1C
IC10
C19
1
6
1
11CI
VNS202RY1A
PbF
1
8R
42C
82C
52C
72C
83C
6
4
C
84C
15C
13R
28R
37R 74R
5
0
1
R
43C
3R
16R
36R
1
1
6R
50
6C
452C962R562R552C
0
62C
016
R
02C 38R
48
R
78C
12C 93C 3
1C
9
7
R
0
4C
C604
R52
C10
R24
R56
C33
C35
R64
R114
R600
74C
05C 86C
36C
6
06C
706C
4
1
C
C36
C29
C30
C26
C31
C32
C37 C49
R507
R106
R78 R50
C12
C67
C66
C64
C54
R609
C225
C233
C232
R607
C221
C222
C223
C224
C62
C61
C65
C53
R101
C608
R604 R603
R601 C603 R244
04
2R
14
2R
5
2
2R
8
12
R
712R
8
52C
722R
0
2
2
C
007C
06C
23R 33R 63R 14R
85C
47R
7
5
C
97C
71
R
606R
506R
R242
C226
R4
R5
R223
C217
C218
C56R60
R44
C81
R89
C80
C201
C200
R46
R77
R75
C219
R224
C609
C44
C6
C227
R251
R263
R264
R85 R86
TD78
TD6 TD62 TD4
TD61
08DT 9
7D
T
68
DT
18DT
48DT
58DT
38DT
28DT
TD9
TD7
TD10
TD31 TD100
TD110
TD102
TD108
TD123
TD111
TD121
TD200
TD45
TD48
TD42
TD106
TD116
901D
T
TD119
TD39
TD120
TD117
TD2
TD69
TD63
TD70
TD71
TD65
TD73
TD68
TD64
TD3
TD12
TD16
TD67
TD72
TD19
TD74
TD66
TD77
C18
C86
TD38
MAIN BOARD
<INDEX>
MAIN BOARD
(PATTERN SIDE)
IC5 A2
IC6 A2,B2
IC7 A2
IC8 A2,B2
IC10 B1
IC11 A1
IC200 A1
(PATTERN SIDE)
IC203 B2,C2
IC205 A2,B2
IC600 OPEN
IC601 B2
Q1 B1,C1
Q500 B1
D1 A1
D2 B1
D3 OPEN
D5 A1
D6 A1,B1
D7 A1,B1
A
B
C
123
5-6
CONDUCTOR VIEW OF MAIN BOARD (PATTERN SIDE)