Haier HWE15XCR-L User manual

Design may vary by model number. El diseño puede variar conforme al
número de modelo
This user manual is to be only used for
electronic control 15,000 BTU, 18,000
BTU and 24,000 BTU.
Este manual del usuario sólo se debe
utilizar para el control electrónico
15,000 BTU, 18,000 BTU y 24,000bBTU.b
HWE15XCR-L
HWE18VCR-L
HWE24VCR-L
User & Care Guide
Guía de uso y cuidado
Room Air Conditioner
Aire acondicionado
de uso doméstico
0010568060

ENGLISH
TABLE OF CONTENTS
PRODUCT REGISTRATION
Thank you for purchasing our Haier
product. This easy-to-use manual will guide
you in getting the best use of your product.
Remember to record the model and serial
numbers. They are on a label on the side of
your unit.
Model number
Serial number
Date of purchase
Staple your receipt to your manual. You will need it to obtain warranty service.
SAFETY INFORMATION.............................................................................................................2
Important Safety Precautions................................................................................................ 2-3
Operational Safety & Warnings..................................................................................................4
INSTALLATION REQUIREMENTS .............................................................................................5
Tools and Parts............................................................................................................................5
Location Requirements ..............................................................................................................6
Electrical Requirements .......................................................................................................7-10
HOW TO INSTALL ....................................................................................................................11
Unpacking the Air Conditioner.................................................................................................11
Preparing the Air Conditioner ............................................................................................11-13
Preparing the Window ..............................................................................................................14
Completing the Installation................................................................................................15-16
USING YOUR AIR CONDITIONER...........................................................................................17
Starting the Air Conditioner...............................................................................................17-21
Using the Remote Control........................................................................................................22
Changing the Air Direction.......................................................................................................22
CARING FOR YOUR AIR CONDITIONER................................................................................23
Cleaning the Air Filter ...............................................................................................................23
Cleaning the Front Panel ..........................................................................................................24
Customer Service.....................................................................................................................24
Normal Sounds of an Air Conditioner......................................................................................25
TROUBLESHOOTING ..............................................................................................................26
LIMITED WARRANTY...............................................................................................................27

1. Use this air conditioner only for its intended application as described in this
Use & Care Guide.
2. This air conditioner must be properly installed and use the correct wall
outlet that matches with the air conditioner’s power supply cord in
accordance with the Installation Section of this Use & Care Guide before
it is operated.
3. Never unplug the air conditioner by pulling on the power supply cord.
Always grip the plug firmly and pull straight out from the wall outlet.
4. Replace the power supply cord immediately if it becomes damaged in any
way. A new power supply cord must be purchased from the air conditioner
manufacturer and installed by a qualified technician. DO NOT use a power
supply cord that is cracked, split, cut, or damaged anywhere along its
length or either at the plug end or connector end.
5. Turn off the air conditioner and unplug it from the wall outlet before
performing any cleaning or maintenance.
6. Do not store or use combustible or flammable materials or liquids on
or near the air conditioner.
7. If the wall outlet configuration does not match the plug configuration
on the air conditioner, the wall outlet must be changed by a qualified
electrician.
PAGE 2 SAFETY INFORMATION
ENGLISH
THE INFORMATION IN THIS USE & CARE GUIDE MUST BE
FOLLOWED TO MINIMIZE THE RISK OF PERSONAL INJURY, FIRE,
ELECTRIC SHOCK OR OTHER UNSAFE CONDITIONS.
THE INSTRUCTIONS IN THIS USE & CARE GUIDE ARE NOT MEANT
TO INCLUDE EVERY POSSIBLE CONDITION OR SITUATION THAT
MAY OCCUR. USE CAUTION AND CARE WHEN INSTALLING, OPERATING
AND CLEANING THE AIR CONDITIONER.
WARNING
IMPORTANT SAFETY PRECAUTIONS

SAFETY INFORMATION PAGE 3
ENGLISH
8. This air conditioner contains R410a refrigerant and requires FHUWLnjHG
technicians to use the proper equipment, tools and safety standards that
are approved for this refrigerant. Use only equipment FHUWLnjHG for R410a
refrigerant. In addition, under federal law, all refrigerant must be properly
removed from the air conditioner prior to its disposal.
For responsible disposal of the product, please contact
or your local municipality for additional recycling options in your area.
READ AND FOLLOW THE
SAFETY INSTRUCTIONS CAREFULLY.
SAVE THESE INSTRUCTIONS
IMPORTANT SAFETY PRECAUTIONS
State of California Proposition 65 Warnings:
WARNING: This product contains one or more chemicals known to the
State of California to cause cancer.
WARNING: This product contains one or more chemicals known to the
State of California to cause birth defects or other reproductive harm.

ENGLISH
OPERATIONAL SAFETY & WARNINGS
1. This air conditioner contains no consumer serviceable parts. If you have
problems or questions regarding the operation of your air conditioner
always call Haier Customer Service: 1-877-337-3639.
2. Be sure that the air conditioner is properly and securely installed in
the window according to the installation instructions included in this
Use & Care Guide.
3. DO NOT drill any holes in the base or sides of the air conditioner.
4. DO NOT place fingers or objects in the air discharge or air intake in the
front of the air conditioner.
5. DO NOT operate the air conditioner with a protective cover on the
outside section.
6. DO NOT block the air discharge or air intake areas on the front panel.
7. DO NOT block the side louvers on the outside of the air conditioner.
8. DO NOT place any objects either on the indoor or outdoor sections of
the air conditioner
9. Operate the air conditioner with the air filter installed.
10. Keep this Use & Care Guide, carton and packing material for future use
in removing, storing and reinstalling the air conditioner.
PAGE 4 SAFETY INFORMATION

ENGLISH
TOOLS AND PARTS
INSTALLATION REQUIREMENTS PAGE 5
Read and follow the instructions provided with any tools listed here.
TOOLS NEEDED
PARTS SUPPLIED:
Check that all parts for your VSHFLnjF air conditioner are included in the parts package.
NOTE: If parts are missing, call Haier Customer Service: 1-877-337-3639.
Phillips head screwdriver
Flat-blade screwdriver
Scissors
Level
Socket wrench & sockets
Tape measure
Drill and 1/8" bit
Pencil
Pliers
Adjustable wrench
IMAGE PART
HWE15XCR-L
HWE18VCR-L
HWE24VCR-L
Top channel 1
Foam seal 1
Installation brackets 2
Window lock bracket 1
3/8" self-tapping screws 12
1" wood screws 8
3/8" bracket screws 6
2-1/2" bolt and lock nut 2*2
Side curtains 2
Side curtain assembly 2
ON/OFF MODE SPEED TIMER TEMP/TIME TEMP/TIME
Remote control 1

ENGLISH
PAGE 6 INSTALLATION REQUIREMENTS
LOCATION REQUIREMENTS
IMPORTANT: Observe all governing codes and ordinances. Check the location where the air
conditioner will be installed. Make sure you have everything necessary for correct installation.
The site of installation should provide:
ŨA grounded electrical outlet within 6 ft. (183 cm) of where the power cord exits the air
conditioner.
NOTE: Do not use an extension cord, plug adapter, surge protector or multi-outlet adapter.
Ũ)ree movement of air in the room to be cooled.
Ũ$ODrge enough opening for the air conditioner.
Ũ8QLWPXVWQot be installed in a through-the-wall sleeve.
NOTE: The outside cabinet louvers and air discharge must not be obstructed by bushes, trees,
etc. Air must be able to pass freely through the cabinet louvers.
WINDOW INSTALLATION 6HH)LJ
Window opening measurements: (See )LJ 1)
HWE15XCR-L, HWE18VCR-L, HWE24VCR-L
A. Width 29-1/2" - 39"
B. Height 19-1/8"
WARNING
Ũ(OHFWULFDOVKRFNKazard
Ũ3OXJLQto a mating, grounded 3 prong outlet.
Ũ'RQot remove the ground prong from the power supply cord.
Ũ'RQot use a plug adapter, extension cord, surge protector, or multi-outlet adapter
Ũ)DLOXre to follow these instructions can result in injurynjre, or electrical shock.
A-WIDTH
%+(,*+7
Fig. 1

ENGLISH
INSTALLATION REQUIREMENTS PAGE 7
ELECTRICAL REQUIREMENTS
1. DO NOT cut or remove the grounding prong on the attached power supply cord. Doing so may
cause sparks or fire, and voids all warranties. For safety purposes the air conditioner must be
properly grounded.
7RDYRLGDILUHKD]DUGRUSRVVLEOHHOHFWULFVKRFN'2127XVHDQDGDSWHUSOXJH[WHQVLRQFRUG
surge protectors, or multi-outlet adapters with the air conditioner.
3. The power supply cord is equipped with a 3-prong plug which mates with the grounded 3-prong
ZDOORXWOHWWRPLQLPL]HWKHSRVVLELOLW\RIHOHFWULFDOVKRFNIURPWKLVDLUFRQGLWLRQHU
7KHSRZHUVXSSO\FRUGLQFOXGHVDOHDNDJHFXUUHQWGHWHFWLRQLQWHUUXSWHUGHYLFH/&',$
RESET and TEST button are on the plug case. The device should be tested on a periodic
basis by pressing the TEST button and then the RESET button while it is plugged into the wall
outlet. If the TEST button does not trip or the RESET will not stay engaged, do not use the air
conditioner and contact a qualified service technician.
5. Have the wall outlet and circuit inspected by a qualified electrician to ensure that the wall outlet
is properly grounded.
6. If there is a 2-prong wall outlet present and not a 3-prong wall outlet, it is the responsibility of
the user to have it replaced with a properly grounded 3-prong outlet.
7. The air conditioner should always be plugged into a dedicated electrical outlet which has a
voltage rating that matches the serial label on the side of the air conditioner.
8. The electrical ratings for your air conditioner are listed on the Model/Serial Number label. The
Model/Serial Number label is located on the side of the air conditioner cabinet.
9. Specific electrical requirements are listed in the chart below. Follow the requirements for the
type of plug on the power supply cord.
ELECTRICAL SAFETY and WARNINGS
WARNING

ENGLISH
PAGE 8 INSTALLATION REQUIREMENTS
ELECTRICAL REQUIREMENTS cont.
POWER SUPPLY CORD (See Fig.2)
Wiring Requirements
For model HWE15XCR-L
Ũ115-volt (103.5 minimum to 126.5 maximum)
Ũ15-amp time-delay grounded fuse or circuit breaker
rUse on single outlet circuit only.
For model HWE18VCR-L
Ũ230/208 volt (187 min. to 253 max.)
Ũ15-amp time-delay fuse or circuit breaker
rUse on single outlet circuit only.
For model HWE24VCR-L
Ũ230/208 volt (187 minimum to 253 maximum)
Ũ20-amp time-delay grounded fuse or circuit breaker
rUse on single outlet circuit only.
REQUIRED GROUNDING METHOD (See Fig.2)
This air conditioner must be grounded. This air conditioner is equipped with a power
supply cord that has a 3 prong grounding plug. The power supply cord must be plugged
into a mating, grounded 3 prong outlet, and grounded in accordance with all local codes and
ordinances. If a mating outlet is not available, it is the customer’s responsibility to contact a
TXDOLnjHG electrician and ensure that a properly grounded 3 prong
outlet is installed.
POWER SUPPLY CORD (See Fig.3)
NOTE: Your air conditioner's plug may GLNjer slightly in appearance
from the one shown.
A. Reset button
B. Test button
This room air conditioner is equipped with an a leakage current detection interrupter (LCDI)
power supply cord required by UL. This power supply cord contains a current detection device.
If the power supply cord is crushed, this device will detect current leakage and power will be
disconnected from the air conditioner. If this power supply cord is damaged, it cannot be
repaired and must be replaced with a cord from the product manufacturer. If the power supply
cord is damaged call Haier Customer Service: 1-877-337-3639.
RESET
TEST
A
B
Fig. 3
Fig. 2
HWE15XCR-L
HWE18VCR-L
HWE24VCR-L
115V
15 Amp
230V
15 Amp
230V
20 Amp

ENGLISH
INSTALLATION REQUIREMENTS PAGE 9
ELECTRICAL REQUIREMENTS cont.
ŨElectrical shock hazard
ŨPlug into a mating, grounded 3 prong
outlet.
ŨDo not remove the ground prong from the
power supply cord.
ŨDo not use a plug adapter, extension cord,
surge protector, or multi-outlet adapter
ŨFailure to follow these instructions can
result in injury, njre, or electrical shock.
WARNING
IMPORTANT: Observe all governing codes and ordinances. Check the location where the air
conditioner will be installed. Make sure you have everything necessary for correct
installation.
THE LOCATION SHOULD PROVIDE:
Ũ$Jrounded electrical outlet within 6 ft. (183 cm) of where the power supply cord exits the air
conditioner, for models: HWE15XCR-L, HWE18VCR-L, HWE24VCR-L
NOTE: Do not use an extension cord, plug adapter, surge protector or multi-outlet adapter.
Ũ)ree movement of air in the room to be cooled.
Ũ$ODrge enough opening for the air conditioner.
ŨThe air conditioner must not be installed in a through-the-wall sleeve. It can only be installed in a
double-hung window or in a wall. .
NOTE: The outside cabinet louvers must not be obstructed by bushes, treesHWF$LUPXVWEHDEOH
to pass freely through the cabinet louvers.

ENGLISH
PAGE 10 INSTALLATION REQUIREMENTS
TO TEST YOUR POWER SUPPLY CORD:
1. Plug power supply cord into a mating, grounded 3 prong outlet.
(See Fig.4)
3UHVV5(6(7RQVRPHGHYLFHVDJUHHQOLJKWZLOOWXUQRQ
3UHVV7(67OLVWHQIRUFOLFN5HVHWEXWWRQZLOOWULSDQGRQVRPHGHYLFHV
DJUHHQOLJKWZLOOWXUQRII
3UHVVDQGUHOHDVH5(6(7OLVWHQIRUFOLFN5HVHWEXWWRQZLOOODWFKDQGRQ
VRPHGHYLFHVDJUHHQOLJKWZLOOWXUQRQ7KHSRZHUVXSSO\FRUGLVUHDG\
for operation.
NOTE:
Ũ
The RESET button must be pushed in completely for proper operation. (See Fig.5)
ŨThe power supply cord must be replaced if it fails to trip when the test
button is pressed or fails to reset.
Ũ
DO NOT turn the air conditioner on or off by unplugging the power
supply cord from the outlet. Always turn the air conditioner on or off at
the control panel or by using the remote control.
Ũ
A damaged power supply cord must be replaced with a new power
supply cord obtained from the product manufacturer and installed my
a qualified service professional. It cannot be purchased at a retail store
and must not be repaired by the user.
If the power supply cord is damaged please call Haier Customer Service:
1-877-337-3639.
Ũ
The power supply cord contains no user-serviceable parts.
Ũ2SHQLQJWKHWDPSHUUHVLVWDQWFDVHYRLGVDOOPDQXIDFWXUHUZDUUDQWLHV
Fig. 4
RESET
TEST
Fig. 5
ELECTRICAL REQUIREMENTS cont.

ENGLISH
HOW TO INSTALL PAGE 11
UNPACKING THE AIR CONDITIONER
REMOVE PACKAGING MATERIALS
Ũ
Remove packaging materials. Save the carton and the foam packaging for storing the unit when
not in use.
NOTE:7KHUHDUH12LQWHUQDOSDFNLQJPDWHULDOVLQVLGHWKHDLUFRQGLWLRQHUWRUHPRYHş'R1RW
open the cabinet.
Ũ
Handle the air conditioner gently.
Ũ
Keep the air conditioner upright and level. Do not set the air conditioner on its side, front, back
or upside down.
Ũ
The air conditioner must be standing upright for 2 hours prior to installation and operation.
Unpack unit in the floor near the installation location
5HPRYHWKHWZRIURQWDWWDFKPHQWVFUHZV$.HHSWKHVHVFUHZVIRUODWHUXVH6HSDUDWHWKH
cabinet from the front panel. (See Fig.6)
5HPRYHWKHWZRVFUHZVSHUVLGH%IRXQGDWWKHERWWRPRIWKHRXWHUFDELQHW8VLQJWKH
basepan handle, slowly and evenly pull out the chassis from the cabinet. Use two or more
people to move the air conditioner.
&$87,211HYHUH[SRVHSODVWLFIURQWRU
JULOOHWRH[WUHPHWHPSHUDWXUHV
EXCESSIVE WEIGHT HAZARD
When moving or lifting the air conditioner, use two or more people.
Wear gloves when handling the air conditioner to protect against
possible sharp edges and metal fins.
WARNING
Fig. 6
PREPARING THE AIR CONDITIONER
A
B
B
B

ENGLISH
PAGE 12 HOW TO INSTALL
PREPARING THE AIR CONDITIONER cont.
Assemble and install side curtains and top channel (See Fig.7)
,QVWDOOWKHWRSFKDQQHOZLWKIRXUŤVHOIWDSSLQJVFUHZV6HH)LJ
2. Slide left-hand curtain assembly into left side of top and bottom channels. Repeat for right-hand
FXUWDLQDVVHPEO\6HH)LJ
)DVWHQFXUWDLQUHWDLQHUVWULSVWRWKHVLGHVRIWKHFDELQHWZLWKHLJKWŤVHOIWDSSLQJVFUHZV
6HOIWDSSLQJVFUHZVRQHDFKVLGH6HH)LJ
Fig. 7
Fig. 8
3/8" Self Tapping Screws
Side Curtains
3/8" Self
Tapping Screws
Top Channel

ENGLISH
HOW TO INSTALL PAGE 13
PREPARING THE AIR CONDITIONER cont.
1. Measure the width of the window opening. (See Fig.9)
2. Mark the center line on the inside of the windowsill with a pencil. (See Fig.10)
INSTALL THE CABINET IN THE WINDOW (See Fig.11)
1. Center the cabinet in the window . Make sure to place the unit so that it is resting on the window
VLOOZLWKDŭtRŭGownward tilt towards the outside. Lower the window sash behind the front
ǍDQJHRIWKHtop channel to hold the unit in place. The bottom channel must rest behind the
window sill. (See Fig.11)
NOTE: The appearance of your model ma\GLNjer from the one shown.
NOTES AND WARNINGS:
Ũ%HVXre your air conditioner does not fall out of the opening during installation or removal.
ŨA grounded electrical outlet must be within 6 ft. (183 cm) of where the power supply cord
exits the air conditioner.
Ũ'RQot block the air discharge or air intake areas on the front panel.
Ũ'RQot block the louvers on the outside of the air conditioner.
Fig. 9 Fig. 10
Fig. 11
WIDTH
CENTER
:,'7+ OF
:,1'OW OPENING CENTER LINE
Top Channel
Lower Window Sash

ENGLISH
PAGE 14 HOW TO INSTALL
PREPARING THE WINDOW
([SDQGERWKFXUWDLQVVRWKH\FRQWDFWWKHZLQGRZIUDPH,QVWDOOIRXUŤZRRGVFUHZVZRRG
screw in each corner of the certain frame.(See Fig.12)
1" Wood
Screws
(2) 1" Wood
Screws
Fig. 12
8VHRQHŤZRRGVFUHZLQWKHWRS
mounting channel.
8VHWZRZRRGVFUHZVWRIL[WKH
case to window sill.
,QVWDOOWZRŤOHYHOLQJEROWVWR
WKHOHIWDQGULJKWEUDFNHWV6HH)LJ
Secure the left and right brackets to the
FDELQHWXVLQJVL[ŤEUDFNHWVFUHZV
7KUHHRQHDFKVLGH6HH)LJ
6. Adjust two 2-1/2" leveling bolts until
contact with outside of the building and
use nut lock to secure bolt. Use a wood
block between the leveling bolts and the
ZDOOLIUHTXLUHG6HH)LJ
Fig. 13 Fig. 14
2-1/2 Bolt and
Nut Lock
Wood Block
3/8"

ENGLISH
HOW TO INSTALL PAGE 15
COMPLETING THE INSTALLATION
COMPLETE THE INSTALLATION
1. Uncoil the included foam seal. (See Fig.15)
2. Insert the foam seal behind the top of the lower window sash and
against the glass of the upper window. (See Fig.16)
3. Place the window lock bracket as shown. Use
DŭŤGULOOELWWRGULOODVWDUWHUKROHWKURXJKWKH
hole in the window lock bracket and into the
XSSHUZLQGRZVLOO6HH)LJ
4. Attach the window lock bracket to the upper
ZLQGRZZLWKRQHŤZRRGVFUHZWRVHFXUH
WKHZLQGRZLQSODFH6HH)LJ
INSTALLING THE CHASSIS TO THE
CABINET (See Fig.18)
When moving or lifting the air conditioner
chassis, use two or more people. Wear gloves when
handling the air conditioner to protect against possible
sharp edges and metal fins.
1. Pick up the chassis carefully and evenly.
2. Slide the chassis into the cabinet. (See Fig.18)
3. Reinstall the front panel.
4. Secure the front panel to the chassis using the screws
UHPRYHGDWWKHVWDUWRIWKHLQVWDOODWLRQ$(See Fig.19)
5HLQVWDOOWZRRIWKHVFUHZVUHPRYHGIURPWKHFDELQHWDWWKHVWDUWRIWKHLQVWDOODWLRQ%(See
Fig.19)
NOTE:7ZRUHDUVFUHZV%QRWUHTXLUHG
6. Press RESET on the power supply cord. A green light will come on. See “Electrical
Requirements."
Fig. 15
Fig. 18
Fig. 16
Top of lower
window sash
Foam seal
Fig. 17
Window Lock
Bracket
A
B
Fig. 19

ENGLISH
PAGE 16 HOW TO INSTALL
COMPLETING THE INSTALLATION
WARNING
Ũ(OHFWULFDOVKRFNKD]DUG
Ũ3OXJLQWRDPDWLQJJURXQGHGSURQJRXWOHW
Ũ'RQRWUHPRYHWKHJURXQGSURQJIURPWKHSRZHUVXSSO\FRUG
Ũ'RQRWXVHDSOXJDGDSWHUH[WHQVLRQFRUGVXUJHSURWHFWRURUPXOWLRXWOHWDGDSWHU
Ũ)DLOXUHWRIROORZWKHVHLQVWUXFWLRQVFDQUHVXOWLQLQMXU\ILUHRUHOHFWULFDOVKRFN
WALL INSTALLATION
Construction and Installation
NOTES:
1. Be certain that the location of the air conditioner in the wall conforms to all local building codes
before installation.
2. Consult with a qualified carpenter concerning installation.
3. When installing the air conditioner in a through-the-wall application, work from inside the room.
(DFKWKURXJKWKHZDOOLQVWDOODWLRQPD\EHXQLTXHWKHUHIRUHQRDGGLWLRQDOSDUWVDUHLQFOXGHG
5. Be certain that the section of the wall being used:
Ũ'RHVQRWKDYHHOHFWULFDOZLULQJLQWKHORFDWLRQZKHUHWKHDLUFRQGLWLRQHUZLOOEHLQVWDOOHG
Ũ'RHVQRWKDYHSOXPELQJSLSHVLQWKHORFDWLRQZKHUHWKHDLUFRQGLWLRQHUZLOOEHLQVWDOOHG
Ũ$QH[LVWLQJHOHFWULFDORXWOHWWKDWPDWFKHVWKHSRZHUVXSSO\FRUGSOXJRIWKHDLUFRQGLWLRQHU,IQR
RXWOHWH[LVWVRUWKHZURQJW\SHRIPDWLQJRXWOHWLVSUHVHQWFRQVXOWZLWKDTXDOLILHGHOHFWULFLDQWR
install the proper outlet.
Ũ'RHVQRWVXSSRUWPDMRUVWUXFWXUDOFRPSRQHQWV
Ũ7KHILQLVKHGVLGHVRIWKHZDOORSHQLQJVKRXOGEHVWUXFWXUDOZDOOPHPEHUV
Ũ2XWVLGHDUHDVDUHQRWEORFNHG
ŨSee “Electrical Requirements" for full detail.
Ũ6WUXFWXUDOLQWHJULW\RIWKHZDOOPXVWEHPDLQWDLQHG3URIHVVLRQDOLQVWDOODWLRQLVVWURQJO\
recommended.

ENGLISH
HOW TO INSTALL PAGE 17
STARTING THE AIR CONDITIONER
Operating your air conditioner properly helps you to obtain the best possible results.
This section explains how to operate this air conditioner.
IMPORTANT:
Ũ nehW you turn RNj the air conditioner , either at the control panel or with the remote control,
wait at least 3 minutes before turning it back on. This prevents the compressor from
overloading. This 3 minute delay also applies when switching from cool mode to fan and
back.
Note: Built in 3 minute delay. You may notice the compressor might not start right away.
Ũ
Do not operate your air conditioner in the Cool mode when the outside temperature is below
61° F (16° C). The inside evaporator coil will freeze up, and the air conditioner will not operate
properly.
POWER
FILTER RESET
CLEAN FILTER INDICATOR
MODE
SPEED
TEMPERATURE / TIME
TIMER

ENGLISH
PAGE 18 USING YOUR AIR CONDITIONER
STARTING THE AIR CONDITIONER cont.
1. Carefully remove the clear plastic njOP from the control panel.
2. Press POWER once to turn on the air conditioner.
NOTE: When the air conditioner is njrst plugged in, the LED display will show “88” for 3 seconds.
After the air conditioner is turned on for the njrst time, the display will show the
temperature Ŏ) and the fan is automatically set to Low speed and the Mode indicator will
show ENERGY SAVE.
ŨTo switch between r) and °C,press UP and DOWN buttons simultaneously and hold for 3
seconds.
NOTE: To switch the temperature display between )DKrenheit ) and &HOVLXV& the air
conditioner must be plugged in, and turned on. The change cannot be done using the
remote control.
3. Select Mode. Refer to “Mode.”
4. Select Speed. Refer to “Speed.”
5. Set Timer. Refer to “Temp/Time”
6. Reset the njOWHU check reminder. Refer to ţ)LOWHU Reset”
MODE
1. Press mode until you see the indicator light come on next to the desired setting.
2. Choose )DQ Energy Save, Cool or Dehum.
FAN - Only the fan runs. Press SPEED to select High, Med or Low fan speed. The display shows
the current room temperature.
NOTE:,Q)$1PRGHWKHWHPSHrature cannot be set.
ENERGY SAVE - In this mode the fan runs only when cooling is needed. The fan will run for
3 minutes after the compressor shuts RNj The fan then cycles on for 1 or 2
minutes at 10 minute intervals until the temperature in the room is above the
set temperature. The compressor then turns back on.
COOL - Cools the room. Press SPEED to select High,Med , Low or Auto Cool fan speed. Press
the TEMP/TIME up or down arrow button to adjust the temperature. The fan will run
continuously in cool mode.
DEHUM - Aids in removing humidity from the room. Dehum mode cannot be used to cool the
room.
NOTE: In Dehum mode, when the set temperature is close to the ambient temperature,
the compressor may stop and the fan will run in low speed only.