Haier QHNG08AA User manual

49- 5000537 Rev. 2 09- 21 GEA
Installation and User Manual
Instruccionesde instalación y
Manual del usuario
QHNG08AA
QHNG10AA
Room Air Conditioner
Accondicionadores de Aire Para Sala
Design may vary by model number.
Some models may have an addit ional
letter after t he model number.
El diseño puede variar según el número
de modelo
Algunos modelos pueden tener una
let ra adicional después del número de
modelo.

249- 5000537 Rev. 2
ENGLISH

49- 5000537 Rev. 2 3
ENGLISH
SAFETY INFORMATION .......................................................................................................4
USING THE AIR CONDITIONER
Controls ............................................................................................................................5
Remote Control .....................................................................................................................6
Cool Mode ..........................................................................................................................6
Energy Saver Mode..................................................................................................................6
Air Direction ........................................................................................................................7
CARE AND CLEANING
Grille and Case ......................................................................................................................7
Air Filter.............................................................................................................................7
Outdoor Coils .......................................................................................................................7
Install Batteries in Remot e ...........................................................................................................7
INSTALLATION INSTRUCTIONS
Before you begin ....................................................................................................................8
Electrical Requirements .............................................................................................................8
Part s Included .......................................................................................................................9
Window Requirement s .............................................................................................................10
Prepare the Air Conditioner.........................................................................................................10
Install the Air Conditioner...........................................................................................................11
Install Support Brackets ............................................................................................................12
TROUBLESHOOTING TIPS ..................................................................................................13
Normal Operating Sounds ..........................................................................................................14
SmartHQ SETUP. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .14
CONSUMERSUPPORT
Limited Warranty...................................................................................................................16
Thank you for purchasing this Haier product. This user manual will
help you get t he best performance from your new air conditioner.
For future reference, record the model and serial number located on
the label on the side of your air conditioner, and the date of purchase.
Staple your proof of purchase to this manual to aid in obtaining
warranty service if needed.
_______________________________________
Model number
_______________________________________
Serial number
_______________________________________
Date of purchase
Record Keeping
TABLEOF CONTENTS

449- 5000537 Rev. 2
ENGLISH
READ AND SAVE THESE INSTRUCTIONS
SAFETY INFORMATION
WARNING For your safety, the information in this manual must be followed to minimize the risk of fire, electric
shock or personal injury.
• Use this appliance only for its intended purpose as
described in this Owner’s Manual.
• This air conditioner must be properly installed in
accordance with the Installation Instructions before it is
used.
• Never unplug your air conditioner by pulling on the power
cord. Always grip plug firmly and pull straight out from t he
receptacle.
• Replace immediately all electric service cords that have
become frayed or otherwise damaged. A damaged power
supply cord must be replaced with a new power supply
cord obtained from the manufacturer and not repaired.
Do not use a cord that shows cracks or abrasion damage
along its length or at either the plug or connector end.
• Turn the unit OFFand unplug your air condit ioner before
cleaning.
• For your safety…do not store or use combustible
materials, gasoline or other flammable vapors or liquids in
the vicinity of this or any other appliance.
• If the receptacle does not match the plug, the receptacle
must be changed out by a qualified electrician.
• Do not use means to accelerate the defrosting process
or to clean, other than those recommended by the
manufacturer.
• The appliance shall be stored in a room without
continuously operating ignition sources (for example:
open flames, an operating gas appliance or an operating
electric heater.
• Do not pierce or burn refrigerant tubing. Be aware that
refrigerants may not cont ain an odor.
• Keep ventilation openings clear of obstruction.
• When handling, installing, and operating the appliance,
care should be taken to avoid damage to the refrigerant
tubing.
• Do not drill holes in the unit.
• Maintenance, cleaning, and service should only be
performed by technicians properly trained and qualified in
the use of flammable refrigerants.
• GEAppliances does not support any servicing of the air
conditioner.
• Dispose of air conditioner in accordance with Federal and
Local Regulations. Flammable refrigerants require special
disposal procedures. Contact your local authorities for the
environmentally safe disposal of your air conditioner.
WARNING
Risk of Fire or Explosion. This unit contains flammable refrigerant.
Additional safety precautions must be followed.

49- 5000537 Rev. 2 5
ENGLISH
Features and appearance will vary.
Lights beside the touch pads on the air conditioner control panel
indicate the selected settings.
Remote Control
Air Conditioner Controls
LOW
AUTO
COOL
SPEED
MODE
MED HIGH
FAN ECO FILTER SLEEP
WIFI
1 2 3 4
5
8 7
9
1. Power Pad
Turns air conditioner on and off. When turned on, the
display will show the Set temperature.
2. Display
Shows the Set temperature or time remaining on the
Delay timer. Shows the Set temperature while setting the
temperature in Cool or Eco modes.
3. Temp and Delay Increase ޔ/ Decrease ޕPads
Use to set temperature or delay time. Temperature can be
set in Cool and Eco mode.
4. Mode Pad
Use to set the air conditioner to Fan Only, Cool, or Eco
mode.
5. Fan Speed Pad
In Cool or Eco mode: Use to set the fan speed t o Auto,
High, Med or Low on the unit.
In Fan Only mode: Use to set the fan speed to High, Med,
or Low on t he unit.
6. Delay Pad (set by remote control only)
Delay ON—When the air conditioner is off, it can be set
to automatically come on in 1 to 24 hours at its previous
mode and fan settings.
Delay OFF—When the air conditioner is on, it can be set to
automatically turn off in 1 to 24 hours.
How to set:
Press the Delay pad on the remote control. Each touch of
the Increase ޔ/ Decrease ޕpads on the remote control will
set the timer in 1-hour intervals.
To review the remaining time on the Delay timer, press
the Delay pad on the remote control. Use the Increase ޔ/
Decrease ޕpads on the remote cont rol to set a new time if
desired.
To cancel t he timer, press Decrease ޕpad on the remote
control until the set time is zero.
7. Sleep Pad (set by air conditioner controlsonly)
The SLEEP mode sets the unit to gradually change
settings over an 8 hour period to allow for some
increased energy efficiency during sleep hours.
The SLEEP mode is available only in COOL and FAN only
settings.
Press the SLEEPmode pad and its light will illuminate.
The fan indicator will stay at the same setting but the air
conditioner will automatically change the FAN speed to
low in either COOL or FAN only mode.
In FAN only mode, the fan will stay in the LOW speed
setting for 8 hours. After 8 hours, the air conditioner will
turn off.
In COOL mode, the fan will stay in the LOW speed
setting for 8 hours from the time t he SLEEPmode pad
was pressed. The air conditioner will also raise the set
point 2°Fin 30 minutes and 2°Fmore in another 30
minutes where it will remain for the next 7 hours. After 8
hours, the air condit ioner will turn off.
While t he unit is in SLEEPmode, pressing any pad will
return it to the sett ings that were in place before the
SLEEPmode pad was pressed.
8. Filter Reset Pad
This feature automatically notifies you t hat the air filter
must be cleaned. The indicator light will come on after 250
hours of operation. Clean the air filter (refer t o page 7),
place it back in the front panel, and press the Filter Reset
pad. The light will go off.
9. SmartHQ Pad
Enables connection of the air conditioner to the home
WiFi.
Download the Haier Home App
For details go to Haierappliances.com.
Solid light indicates WiFi
connected
Blinking light indicates
connecting
See Appliance Communication
section in this manual
CONTROLS
1
4
5
6
3
Power
Speed
Mode
Eco Delay

649- 5000537 Rev. 2
ENGLISH
Remote Control
• To ensure proper operation, aim the remote cont rol at t he
signal receiver on the air condit ioner.
• The remote control signal has a range of up to 20 feet.
• Make sure not hing is between the air conditioner and the
remote control that could block the signal.
• Make sure batteries are fresh and installed correctly as
indicated on the remot e control.
Do Not Operate in Freezing Outdoor Conditions
This cool- only air conditioner was not designed for freezing
outdoor conditions.
It must not be used when the outdoor temperature is below
freezing (32°F).
Cool Mode
Use the Cool mode at Low, Med, High or Speed for cooling.
Use the Temperature Increase ޔ / Decrease ޕ pads to set
t he desired temperature bet ween 64°F and 86°F in 1°F
increments.
An electronic t hermostat is used to maintain the room
temperature. The compressor will cycle on and off to keep
the room at the set level of comfort. Set the thermostat at a
lower number and the indoor air will become cooler. Set the
thermostat at a higher number and the indoor air will become
warmer.
NOTE:Òé÷ëèäìõæòñçì÷ìòñèõìöòééäñçìö÷ëèñ÷øõñèçòñwhile set to a Cool setting or if t urned from a fan setting to
aCool setting, it may t ake approximately 3 minut es for the
compressor to start and cooling to begin.
Cooling Descriptions
For Normal Cooling—Select the Cool mode and
High or Med fan with a middle set temperature.
For Maximum Cooling—Select the Cool mode
and High fan with a lower set temperature.
For Quieter and Nighttime Cooling—Select the
Cool mode and Low fan with a middle set temperature.
Eco Mode
Controls the fan.
ON—The fan will cycle on and off wit h the compressor. This
may result in wider variations of room temperature and
humidity. NOTE: the fan may continue t o run for a short time
or may pulse intermit tently after the compressor cycles off to
sample the room air.
OFF—The fan runs all the time, while the compressor cycles
on and off.
Fan Only Mode
Use the Fan Only Mode at Low, Med or High fan speed to
provide air circulation and filtering without cooling. Since
fan-only settings do not provide cooling, a Set temperature
cannot be ent ered. The room temperature will appear in the
display.
Auto Fan Mode
Set to Auto for the fan speed to automatically set to the
speed needed to provide optimum comfort settings with the
set temperature.
If the room needs more cooling, the fan speed will
automatically increase. If the room needs less cooling, the fan
speed will automatically decrease.
Control Panel Lights On/ Off Feature
This air conditioner has a control panel lights on/ off feature
where its lights will turn off when there is no activity with the
controls for over one minute. To wake up the controls, press
any pad on t he controls and t he light s will come on to show
the previous settings.
To turn this feature off, press and hold the SLEEP pad, on the
unit, for 5 seconds. The unit will beep to signal the successful
toggle of t he feature on and off.
USING THEAIRCONDITIONER

49- 5000537 Rev. 2 7
ENGLISH
Air Direction
Use the levers to adjust the air direction left or right.
Tilt the louver bank to adjust up and down.
Grille and Case
Turn the air conditioner off and remove the plug from the wall
outlet before cleaning.
To clean, use water and a mild detergent. Do not use bleach or
abrasives.
Air Filter
The air filter behind the front grille should be checked and
cleaned at least every 30 days or more often if necessary.
To remove:
Open the inlet grille by pulling downward on the tabs at the
top upper corners of the inlet grille until the grille is in a 45º
position. Remove the filter.
Clean the filt er wit h warm, soapy water. Rinse and let the filter
dry before replacing it. Do not clean t he filter in a dishwasher.
CAUTION
ÍØ×ØÝòóèõä÷è÷ëèäìõæòñçì÷ìòñèõúì÷ëòø÷äéìï÷èõåèæäøöèdirt and lint will clog it and reduce performance.
Outdoor Coils
The coils on the outdoor side of the air conditioner should be
checked regularly. If they are clogged with dirt or soot, they
may be professionally cleaned.
USING THEAIRCONDITIONER
CAREAND CLEANING
How to Insert the Batteries in the Remote Control
1. Remove the battery cover by sliding it according to the
arrow direction.
2. Insert new batteries, making sure that the (+) and (–) of
battery are installed correctly.
3. Reattach the cover by sliding it back into position.
NOTES:
• Use 2 “AAA” (1.5 volt) batteries. Do not use rechargeable
batteries.
• Remove the batteries from the remote control if the
system is not going to be used for a long time.
• Do not mix old and new batteries. Do not mix standard
(carbon-zinc) or rechargeable (ni-cad, ni-mh, etc) batteries.

849- 5000537 Rev. 2
ENGLISH
BEFORE YOU BEGIN
Read these instructions completely and carefully.
•IMPORTANT –Save these instructions
for local inspect or’s use.
•IMPORTANT –Observe all governing
codes and ordinances.
• Note to Installer – Be sure to leave these
instructions with the Consumer.
• Note to Consumer – Keep these instructions for
future reference.
• Skill level – Installation of this appliance requires
basic mechanical skills.
• Completion time – Approximately 1 hour
• We recommend that two people install
this product.
• Proper installat ion is the responsibility
of the installer.
• Product failure due to improper installation is not
covered under t he Warranty.
• You MUST use all supplied parts and use proper
installation procedures as described in these
instructions when installing this air condit ioner.
These models require a 115/ 120-volt AC, 60-Hz
grounded outlet protected with a 15-amp
time- delay fuse or circuit breaker.
The 3-prong grounding plug minimizes the
possibilit y of electric shock hazard. If the wall outlet
you plan to use is only a 2-prong outlet, it is your
responsibilit y to have it replaced wit h a properly
grounded 3-prong wall outlet.
CAUTION
Do not, under any circumstances, cut or remove the
third (ground) prong from the power cord.
Do not change the plug on the power cord of this air
conditioner.
Aluminum house wiring may present special problems—
consult a qualified electrician.
ELECTRICAL
REQUIREMENTS
Power cord includes a current interrupter device. A test
and reset button is provided on the plug case. The device
should be tested on a periodic basis by first pressing the
TESTåø÷÷òñäñç÷ëèñ÷ëèRESETåø÷÷òñúëìïèóïøêêèçinto the outlet. If t he TESTåø÷÷òñçòèöñò÷÷õìóòõìéthe RESETåø÷÷òñúìïïñò÷ö÷äüèñêäêèççìöæòñ÷ìñøèuse of the air conditioner and contact a qualified service
technician.
ELECTRICAL
REQUIREMENTS (cont)
TOOLS YOU WILL NEED
Phillips head screwdriver
Ruler or tape measurePencil
Level Scissors or knife
Drill and 1/ 8” drill bit
INSTALLATION INSTRUCTIONS

49- 5000537 Rev. 2 9
ENGLISH
DELAY
MODE
ON/OFF
SPEED
TEMP/TIME
TEMP/TIME
Side Curtain
Frame
Type B (9)
Foam top window
gasket
Side Curtain
(2)
Top mounting rail
Air
conditioner
Window locking
bracket (1)
Side Bracket s
(2)
ÙÊÛÝÜÒ×ÌÕÞÍÎÍ(Appearance may vary)
Bottom Seal and
Side Seals (3)
Left Right
Type A (4)
Side Curtain
Foam (2)
INSTALLATION INSTRUCTIONS

10 49- 5000537 Rev. 2
ENGLISH
3. ÙÛÎÙÊÛÎÝÑÎÊÒÛÌØ×ÍÒÝÒØ×ÎÛ
A. Install the top mounting rail with Type A screws, 4
for AHH10 and 3 for AHH08, from t he outside of the
case.
B. Apply the weather seals provided to the bottom,
top and sides of the window to the seal around the
perimeter of the air condit ioner.
C. Slide the side curtain panels into the side panel rails.
D. Slide left and right side curtain frames into top and
bot tom rails. Make sure that side curtains snap into
side of the frames.
!àÒ×ÍØàÛÎÚÞÒÛÎÖÎ×ÝÜ• These inst ruct ions are for a standard double- hung
window. You will need to modify them for other
types of windows.
• The air condit ioner can be installed without the
side curt ain panels if needed to fit in a narrow
window. See the window opening dimensions.
• All supporting parts must be secured to firm wood,
masonry or metal.
• The electrical out let must be within reach of the
power cord.
• Follow the dimensions in the table and illustration
for your model.
2. ÜÝØÛÖàÒ×ÍØàÛÎÚÞÒÛÎÖÎ×ÝÜ
A storm window frame will not allow the air
conditioner to tilt toward the outside, and will keep
it from draining properly. To adjust for this, attach a
piece of wood to the sill.
àØØÍÙÒÎÌÎÜWIDTH: 2ėLENGTH: Long enough to fit inside the window
frame.
THICKNESS: To determine the thickness, place
äóìèæèòéúòòçòñ÷ëèöìïï÷òðäîèì÷!¦"ėëìêëèõthan the top of the storm window frame or the vinyl
frame.
Attach securely with nails or screws provided by t he
installer.
A
(With side curtain panels)
B
!¦"ėëìêëèõ
than storm
window
frame
St orm window
frame
Wood
Sill
!¦"ėëìêëèõ
than vinyl frame
(on some windows)
Vinyl frame
Models A B
QHNG08 15 1/ 16” min 24”-38”
QHNG10 15 5/ 8” min 26 1/ 8” - 37 3/ 4”
Cut and apply
weather strip to
front and bot tom
edge of window
frame.
Cut and apply
weather strip to
back edge of
the window sill.
Cut and apply
a weather strip
to side of t he
curt ain frame
(one on each
side).
Top Mounting rail
Bottom
mounting
rail
Snap curtain
into frame
INSTALLATION INSTRUCTIONS

49- 5000537 Rev. 2 11
ENGLISH
%ÜÎÌÞÛÎÊÒÛÌØ×ÍÒÝÒØ×ÎÛA. Loosen t he screw on the right hand side of the air
conditioner near the bot tom.
B. Slide a side bracket over the screw so that the
bracket is resting on the window sill. Tighten the
screw.
C. Use a 1/8” drill bit to drill a starter hole into the
window sill through the holes in the side bracket.
Use 4 type B screws to attach the side bracket to the
window sill.
D. Repeat the side bracket installation on t he left side.
E. Measure and cut adhesive foam backed sheet. Apply
over side curtain and frame.
4. INSTALL THE AIRCONDITIONER
IN THE WINDOW
A. Mark the center of the window. Set the air
conditioner in the window so that is it centered.
Place the air conditioner so that front edge of t he
bot tom mounting rail is against the back edge of the
sill.
B. Bring t he window down so that the front edge of the
top mounting is in front of t he window. Make sure
that the air conditioner is level or tilting slightly to
the outside.
C. Extend the curtain panels until they fill the window.
Mark the location of the holes in each corner. Use
the drill and 1/ 8” drill bit to drill pilot holes. Use 4
type B screws to secure t he side panels in place.
Type B screws
INSTALLATION INSTRUCTIONS

12 49- 5000537 Rev. 2
ENGLISH
6. INSTALL WINDOW LOCK BRACKET
AND FOAM TOP WINDOW GASKET
Use Type B Screw to install t he window lock
bracket on t op of the bottom window.
A.
CAUTION
To prevent broken glass or
damage to windows, on vinyl
or other similarly constructed
windows, attach the window
locking bracket to the
window side jamb with one
Type B screw.
B. Cut t he foam top window
gasket to the window width.
C. Stuff the foam between the glass and the window
to prevent air and insects from get ting into the
room.
NOTE: If the
gasket supplied does not fit your window, obtain
appropriate material locally to provide a proper
installation seal.
Wood
Vinyl
INSTALLATION INSTRUCTIONS

49- 5000537 Rev. 2 13
ENGLISH
Save time and money! Review the charts on the following pages first and you may not need to call for service.
Problem Possible Cause What To Do
Air conditioner does not
start.
The unit is unplugged. Make sure the air conditioner plug is pushed completely into
the outlet.
The fuse is blown/ circuit breaker is
tripped.
Check the house fuse/ circuit breaker box and replace the fuse
or reset the breaker.
Power Failure. The unit will automatically restart in the setting last used after
the power is restored.
There is a prot ective t ime delay (approximately 3 minutes) to
prevent tripping of the compressor overload. For this reason,
the unit may not start normal cooling for 3 minutes after it is
turned back on.
The current interrupter device is
tripped.
Press RESET button located on the power cord plug.
If the RESET button will not stay engaged, discontinue use of
the air conditioner and contact a qualified service technician.
Air conditioner does not cool
as it should.
Indoor airflow is restricted. Make sure there are not curtains, blinds or furniture blocking
the front of the air conditioner.
The temp control may not be set
properly.
Turn the temperature cont rol to a higher number.
The air filter is dirty. Clean the filter at least every 30 days. See Care and Cleaning
section.
The room may have been hot. When the air conditioner is first turned on, you need t o allow
time for the room to cool down.
Cold air is escaping. Check for open furnace registers and cold air ret urns.
Cooling coils have iced up. See “Air conditioner freezing up” below.
Air conditioner freezing up Ice blocks the air flow and stops
the air conditioner from cooling the
room.
Set the mode control to High Fan or High Cool with the
temperature setting as high as it can be set.
Water drips outside Hot, humid weather. This is normal.
Water drips inside The air conditioner is not tilted to
the outside.
For proper disposal, make sure the air conditioner slants
slightly from the case front to the rear.
Water collects in base pan Moisture removed from air and drain
into base pan.
This is normal for a short period in areas with little humidity;
normal for a longer period in very humid areas.
TROUBLESHOOTING

14 49- 5000537 Rev. 2
ENGLISH
• You may hear a pinging noise caused by water being picked up and thrown against the condenser on rainy days or when the
humidity is high. This design feature helps remove moisture and improve efficiency.
• You may hear the thermostat click when the compressor cycles on and off.
• Water will collect in the base pan during high humidity or on rainy days. The water may overflow and drip from the outdoor
side of the unit .
• The fan may run even when the compressor does not.
• Water droplets being thrown against the outside coils can make a pinging noise. This helps cool the condenser. You can
reduce t his noise by removing the subbase water plug.
Removing this plug will lower the Energy Efficiency of your until.
NOTE: Do not drill hole in the base pan.
Subbase Water Plug
Haier SmartHQ (for customers in the United States)
Haier SmartHQ Enabled*. If your Air Condit ioner (AC) has a Connected Appliance Information label located on the outside
as shown below, your AC is Haier Appliances SmartHQ Enabled. A WiFi communication card is built into the product allowing it
to communicate with your smart phone for remote monitoring, control and notifications.
Please download the Haier Home App . For details go to Haierappliances.com to learn more about connected appliance
features, and to learn what connected appliance apps will work with your smart phone.
WiFi Connectivity: For assistance with the appliance or the Connect Plus network connectivity (for models that are WiFi enabled
or WiFi opt ional), please call 1- 800- 220- 6899.
Network: GE_MODULE_XXXX
PASSWORD: XXXXXXXX
MAC ID: XX-XX-XX-XX-XX-XX
CONTAINS FCCID: 2ALD3-MKQTWIFI11 CONTAINS IC: 22987-MKQTWIFI11
NORMAL OPERATING SOUNDS
WIFI SETUP

49- 5000537 Rev. 2 15
ENGLISH
REGULATORY INFORMATION
FCC/ IC Compliance Statement:
This device complies wit h Part 15 of the FCC Rules.
Operation is subject to t he following t wo conditions:
1. This device may not cause harmful interference.
2. This device must accept any interference received,
including interference that may cause undesired
operation.
This equipment has been tested and found to comply with
t he limit s for a Class B digit al device, pursuant to Part 15
of the FCC Rules. These limit s are designed to provide
reasonable protection against harmful interference in a
residential installation. This equipment generates uses
and can radiate radio frequency energy and, if not installed
and used in accordance wit h the inst ruct ions, may cause
harmful interference to radio communications. However,
there is no guarantee t hat interference will not occur in a
part icular installation. If this equipment does cause harmful
interference to radio or television reception, which can be
determined by turning t he equipment off and on, t he user
is encouraged to try to correct the int erference by one or
more of the following measures:
• Reorient or relocate the receiving antenna.
• Increase the separation bet ween t he equipment and
receiver.
• Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
• Consult t he dealer or an experienced radio/television
technician for help.
Labelling: Changes or modifications to this unit not
expressly approved by the manufacturer could void t he
user’s authority to operate the equipment .
*Select Models Only
This product has Wi-Fi capability and requires Internet
connectivity and a wireless router to enable interconnection
with an Energy Management System, and/ or with ot her
external devices, systems or applications.
How it Works
Download the SmartHQ App Use the app to connect your room air
conditioner to WiFi
Once connected, use the app to turn
down your air conditioner as you leave
work.
CHANGE TEMP
TO 65
Getting Started
To connect your room air conditioner, you’ll need the
SmartHq App. The app will walk you through the connection
process. Download the app from iTunes or Google Play.
All connected appliace data is held in strict accordance with
the Haier Appliances Connected Data Privacy Policy. Visit
geappliances.com/ privacy/privacy_policy_connected to
view this policy.
Questions about SmartHQ
Get answers you need about setting up WiFi appliances and
connecting to your home network in our support art icles.
Visit products.geappliances.com/appliance/gea-support-
search-content to view SmartHQ room air conditioner
support articles.
SMARTHQ SETUP

16 49- 5000537 Rev. 2
ENGLISH
LIMITED WARRANTY
Staple your receipt here. Proof of the original purchase date is needed to make awarranty claim.
EXCLUSION OF IMPLIED WARRANTIES- Your sole and exclusive remedy isproduct repair asprovided in this
Limited Warranty. Any implied warranties, including the implied warranties of merchantability or fitnessfor a
particular purpose, are limited to one year or the shortest period allowed by law.
For US Customers: This limited warranty is extended to the original purchaser and any succeeding owner for
products purchased for home use within the USA. If the product is located in an area where service by a GEAppliances
Authorized Servicer is not available, you may be responsible for a trip charge or you may be required to bring the
product to an Authorized GEAppliances Service location for service. In Alaska, the limited warranty excludes the cost
of shipping or service calls to your home.
Some states do not allow the exclusion or limitation of incidental or consequential damages. This limited warranty
gives you specific legal rights, and you may also have other rights which vary from state to state. To know what your
legal rights are, consult your local or state consumer affairs office or your state’s Attorney General.
Warrantor US:
GEAppliances, a Haier company
Louisville, KY 40225
• Customer instruction. Thisowner’s manual provides
information regarding operating instructionsand user
controls.
• Improper installation. If you have an installation problem,
or if the air conditioner isof improper capacity, contact
your dealer or installer. You are responsible for providing
adequate electrical connecting facilities.
• Failure of the product resulting from modificationsto the
product or due to unreasonable use includingfailure to
provide reasonable and necessary maintenance.
• Replacement of house fusesor resetting of circuit breakers.
• Failure due to corrosion on modelsnot corrosion-protected.
• Damage to the product caused by improper power supply
voltage, accident, fire, floodsor actsof God.
• Incidental or consequential damage caused by possible
defects with thisair conditioner.
• Damage caused after delivery.
What Will Not Cover:
For The Period Of: Will Replace:
One Year
From the date of the
original purchase
Replacement, repair, or refund of the original retail price for any product which fails due
to a defect in materials or workmanship. If the unit is exchanged, the replacement unit
is warranted for the remainder of your product’s original one-year warranty period. GE
will, at its sole discretion, replace the product with a product of the same or comparable
functionality and quality or refund the original retail price.
•Properly pack your unit. We recommend using the original
carton and packing materials.
• Return the product to the retail location where it was
purchased.
•Include in the package a copy of the salesreceipt or other
evidence of date of original purchase. Also print your name
and addressand a description of the defect.
In Order to Make a Warranty Claim During Your Retailer’s Allowable Return Period:
• Locate your original sales receipt and make anote of your
model and serial number.
• Please visit Haierappliances.com/ support/ schedule-service
to initiate the product replacement process.
• You will be asked to provide your name, address, date of
purchase, model and serial number.
• GEAppliances will arrange for acarton to be sent to your home
to recover the product.
•Please return all requested materials (postage pre- paid) in the
carton provided. Please include a descript ion of the defect .
• You should receive your replacement product or refund within
7 to 10 business days after your package is received.
In Order to Make a Warranty Claim During the Remainder of the One-Year Warranty:

49- 5000537 Rev. 2 1
ESPAÑOL
INFORMACIÓN A TENEREN CUENTA
Le agradecemos la compra de este producto de marca Haier. Este
manual para el usuario le ayudará a obtener el mejor funcionamiento de
su nueva acondicionador de aire.
Para referencia fut ura, anote el modelo y número de serie en la et iquet a
en el lado de su acondicionador de aire, y la fecha de compra.
Engrape la prueba de compra a este manual para asistirle cuando
necesite obtener servicio bajo la garantía.
_______________________________________
Número de modelo
_______________________________________
Número de serie
_______________________________________
Fecha de compra
INFORMACIÓN DE SEGURIDAD ...............................................................................................2
USO DEL ACONDICIONADOR DE AIRE
Cont roles ..........................................................................................................................3
Control Remoto ...................................................................................................................4
Modo de Frío ......................................................................................................................4
Modo de Eco (Ahorro de Energía) ...................................................................................................4
Dirección del Aire ..................................................................................................................5
CUIDADO Y LIMPIEZA
Parrilla y Caja ......................................................................................................................5
Filtro de Aire ......................................................................................................................5
Bobinas Externas ..................................................................................................................5
Instalación de Baterías en el
Modo Remoto .....................................................................................................................5
INSTRUCCIONES DE INSTALACIÓN
Antes de comenzar ................................................................................................................6
Requisitos Eléctricos ..............................................................................................................6
Partes Incluidas . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7
Requisitos de la Ventana ...........................................................................................................8
Preparación del Acondicionador de Aire ............................................................................................8
Instalación del Acondicionador de Aire .............................................................................................9
Instale el Soporte de la Traba de
la Ventana ........................................................................................................................10
CONSEJOS PARA LA SOLUCIÓN DE PROBLEMAS .......................................................................11
Sonidos de Funcionamiento Normal ...............................................................................................12
CONFIGURACIÓN SMARTHQ . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .12
SOPORTE AL CLIENTE
Garantía LImitada. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
ÍNDICE

249- 5000537 Rev. 2
ESPAÑOL
LEA Y GUARDE ESTAS INSTRUCCIONES
SEGURIDAD DEL ACONDICIONADORDEAIRE
Para su seguridad, siga las instrucciones de este manual a fin de minimizar riesgosde incendio, descargas
eléctricas o heridas personales.
• Use este electrodoméstico sólo para su propósito original, como
se describe en el Manual del Propietario.
• Este acondicionador de aire se debe instalar de forma apropiada
de acuerdo con las Instrucciones de Instalación antes de ser
usado.
• Nunca desenchufe su acondicionador de aire empujando el cable
de corriente. Siempre tome su enchufe de manera firme y empuje
el mismo hacia afuera del receptáculo.
• Reemplace de inmediato todos los cables del servicio de
electricidad pelados o con cualquier tipo de daño. Un cable del
servicio de corriente que esté dañado deberá ser reemplazado
por uno nuevo provisto por el fabricante, y no deberá ser
reparado. No use un cable con cortaduras o abrasión sobre su
extensión o en cualquiera de sus enchufes o extremos.
• Coloque la unidad en OFF (Apagado) y desenchufe el
acondicionador de aire antes de usar el mismo.
• Para su seguridad... no acumule ni use materiales combustibles,
gasolina u ot ros vapores o líquidos inflamables cerca de éste u
otro elect rodoméstico.
• Si el receptáculo no coincide con el enchufe, el cambio del mismo
deberá ser realizado por un electricista calificado.
ADVERTENCIA
• A fin de acelerar el proceso de descongelación o para
limpiar, no use ningún método que no sea el recomendado
por el fabricante.
• Este electrodoméstico deberá ser guardado en una
sala donde no haya fuentes de encendido continuas
(por ejemplo: llamas abiertas, un elect rodoméstico que
funcione a gas o un calefactor que funcione a electricidad).
• No perfore ni queme el tubo refrigerante. Tenga presente
que los refrigerantes no deben tener olor.
• Mantenga las aberturas de la ventilación libres de
obstrucciones.
• Al mover, instalar y operar el electrodoméstico, se deberá
tener cuidado para evitar dañar la tubería del refrigerante.
• No realice perforaciones en la unidad.
• El mantenimiento, la limpieza y el servicio técnico sólo
deberán ser realizados por técnicos adecuadamente
entrenados y calificados en el uso de refrigerantes
inflamables.
• GEno suministra servicio técnico para el acondicionador
de aire.
• Descarte el electrodoméstico de acuerdo con las
Regulaciones Federales y Locales. Los refrigerantes
inflamables requieren procedimientos de descarte
específicos. A fin de descartar su acondicionador de aire
de forma ambientalmente segura, comuníquese con las
autoridades locales.
Riesgo de Incendio o Explosión. Esta unidad contiene refrigerante inflamable.
Se deben seguir las precauciones adicionales de seguridad.
ADVERTENCIA

49- 5000537 Rev. 2 3
ESPAÑOL
Las funciones y la apariencia podrán variar.
Las luces junto a las teclas táctiles del panel de control del
acondicionador de aire indican las configuraciones seleccionadas.
1. Tecla de Power (Encendido)
Apaga y prende el acondicionador de aire.
Al encenderse, la pantalla mostrará latemperatura ambiente.
2. Pantalla
Muestra latemperatura ambiente o el tiempo restante en el
Sincronizador de retardo. Muestra latemperatura Definida al
configurar la temperatura en los modos Cool (Frío) o de Energy
Saver (Ahorro de energía). La luz de Ajuste se encenderá durante
laconfiguración.
3. Teclasde Temp Aumento ޔ/ Reducción ޕ
Usado para ajustar la temperatura cuando se encuent re en el
modo Cool (Frío) o Energy Saver (Ahorro de energía). La luz de
Ajuste se encenderá durante la configuración.
4. Tecla de MODO
Usado para ajustar el acondicionador de aire
al modo Cool (Frío) oEnergy Saver (Ahorro de energía).
%ÝèæïäöçèÏäñÜóèèç¤ßèïòæìçäççèïùèñ÷ìïäçòõ¥En modo Cool (Frío) o Energy Saver (Ahorro de energía):
Use las mismas para configurar la velocidad del vent ilador en
Auto, High (Alto), Med (Medio), oLow (Bajo) en la unidad.
En modo ÝèæïäöçèÏäñÜóèèç¤ßèïòæìçäççèïùèñ÷ìïäçòõ¥:
Use las mismas para configurar la velocidad del vent ilador en High
(Alto), Med (Medio), o Low (Bajo) en la unidad.
6. Tecla de Retraso
Delay ON (Retraso Encendido)—Cuando el acondicionador
de aire se encuentre apagado, se podrá configurar para que se
encienda automáticamente en un período de entre 1 y 24 horas
en el modo y configuraciones del vent ilador previas.
Delay OFF(Retraso del Apagado)—Cuando el acondicionador
de aire se encuentre encendido, se podrá configurar
automáticamente para que se apague en un período de ent re 1 y
24 horas.
Cómo configurar:
Presione la tecla Delay 1–24hr (Ret raso ent re 1 y 24 hrs.) en la
unidad o en el control remoto. Cadavez que presione las teclas
Increase (Incrementar) ޔ/ Decrease (Reducir) ޕde la unidad del
control remoto se ajustará el temporizador por intervalos de 1
hora.
Para revisar el tiempo restante en el temporizador de Delay
1–24hr (Retraso entre 1 y 24 hrs), presione la tecla Delay 1–24hr
(Retraso entre 1 y 24 hrs.) de la unidad o del control remoto. Use
las teclas Increase (Incrementar) ޔ/ Decrease (Reducir) ޕde la
unidad del control remoto para configurar un t iempo nuevo si así
lo desea.
Para cancelar el temporizador, presione la tecla reducir – en la
unidad o en el control remoto, hasta que el tiempo configurado
seacero. Luego de 3 segundos, la luz de la tecla Delay 1- 24 hour
(Retraso de 1 a 24 horas) se apaga.
7. Tecla de Sleep (Dormir) (establecido solo por los controles del
acondicionador de aire)
El modo SLEEP(Dormir) configura la unidad para que
gradualmente cambie las configuraciones en un período
de 8 horas, afin de permitir cierto incremento de eficiencia
energética durante las horas de inactividad.
El modo SLEEP(Dormir) está disponible sólo en las
configuraciones COOL (Frío) y FAN (Vent ilador).
Presione la tecla del modo SLEEP(Dormir) y la luz se
encenderá. El indicador del ventilador permanecerá en la
misma configuración, pero el acondicionador de aire cambiará
automáticamente la velocidad del vent ilador a LOW (Bajo) ya
sea en el modo COOL (Frío) o FAN (Vent ilador).
En el modo FAN (Vent ilador) únicamente, el ventilador
permanecerá en la configuración de velocidad LOW (Bajo)
durante 8 horas. Después de 8 horas, el aire acondicionado se
apagará.
En el modo COOL (Frío), el vent ilador permanecerá en la
configuración de velocidad LOW (Bajo) durante 8 horas desde
el momento en que la tecla del modo SLEEP (Dormir) sea
presionada. El acondicionador de aire también elevará el punto
de configuración 2°Fen 30 minutos y 2°Fmás en otros 30
minutos, donde permanecerá durante las siguientes 7 horas.
Después de 8 horas, el aire acondicionado se apagará.
Mient ras la unidad se encuent re en el modo SLEEP
(Dormir), presionar cualquier tecla hará que regrese a las
configuraciones que fueron ajustadas antes de que se
presionara la tecla del modo SLEEP(Dormir).
8. Tecla de Reinicio del Filtro
Estafunción automática le notifica que el filtro de aire debe ser
limpiado. La luz indicadora se encenderá luego de 250 horas de
funcionamiento. Limpie el filtro de aire (consulte la página 5),
vuelvaacolocarlo en el panel frontal, y presione la teclaFilter
Reset (Reinicio del Filtro). La luz se apagará.
9. Tecla SmartHQ
Permite la conexión del acondicionador de aire con el WiFi
hogareño.
Descargue la Aplicación Hogareña de Haier --.
Para más detalles, visite Haierappliances.com.
Controlesdel Acondicionador de
Aire Control Remoto
LOW
AUTO
COOL
SPEED
MODE
MED HIGH
FAN ECO FILTER SLEEP
WIFI
1 2 3 4
5
8 7
9La luz sólida indica que el Wi-Fi está
conectado
La luz parpadeante indica que se
está conectando
Consult e la sección de
Comunicación del electrodoméstico
de este manual
CONTROLES
1
4
5
6
3
Power
Speed
Mode
Eco Delay

449- 5000537 Rev. 2
ESPAÑOL
Control Remoto
• Para asegurar un uso apropiado, apunte el control remoto al
receptor de señal del acondicionador de aire.
• La señal del cont rol remoto cuenta con un alcance de hasta 20
pies.
• Asegúrese de que no haya obstrucciones entre el acondicionador
de aire y el control remoto que pudieran bloquear la señal.
• Asegúrese de que las pilas sean nuevas y que estén instaladas
correctamente, como se indica en el cont rol remoto.
No Utilizar con CondicionesClimáticasExteriores de Congelación
Este acondicionador de aire sólo frío no fue diseñado para uso con
condiciones climáticas exteriores de temperatura helada. No deberá
ser usado con condiciones climáticas exteriores de temperatura
helada.
Modo Cool (Frío)
Use el modo Cool (Frío) a Low (Bajo), Med (Medio), High (Alto)
oAuto Fan Speed (Velocidad de ventilador automática) para
enfriar. Use las teclas de Temperature (Temperatura) Aumento ޔ
/ Reducción ޕpara ajustar a la temperatura deseada ent re 64ºF y
86ºF en incrementos de 1ºF.
Se usaun termostato electrónico para mantener la temperatura
ambiente. El compresor hará ciclo entre apagado y encendido
para mantener la habitación a la temperatura deseada. Ajuste el
termostato a un número menor y el aire interno se enfriará más.
Si lo ajusta a un número mayor, la temperatura del aire interno se
calentará más.
NOTA: Si el acondicionador de aire está apagado y luego se
enciende mient ras se ajusta en la configuración Cool (Frío) o si se pasa
de una configuración de vent ilación a una configuración de Cool (Frío),
es posible que al compresor le tome aproximadamente 3 minutos
comenzar y que comience la refrigeración.
Descripciones de enfriamiento
Para enfriamiento normal—Seleccione el modo Cool (Frío) y ventilador
High (Alto) oMed (Medio) con una temperatura de ajuste media.
Para enfriamiento máximo—Seleccione el modo Cool (Frío) y
ventilador High (Alto) con una temperatura de ajuste menor.
Para enfriamiento silencioso y enfriamiento nocturno—
Seleccione el modo Cool (Frío) y ventilador Low (Bajo) con una
temperatura de ajuste media.
Eco (Modo de ahorro de energía)
Controla el ventilador.
ON (ENCENDIDO)—El ventilador hará un ciclo de encendido
y apagado con el compresor. Este resulta en variaciones
mayores en la temperatura de la habitación y en la humedad.
NOTA: es posible que el ventilador continúe funcionando
durante un período de tiempo corto o que titile de forma
intermitente cuando el compresor finalice su ciclo para probar
el aire de la sala.
OFF (APAGADO)—El ventilador funciona todo el tiempo,
mientras que el compresor pasa por los ciclos de encendido y
apagado.
Modo de Fan Only (Solo ventilador)
Use Fan Only Mode (Modo de Sólo Vent ilador) en la velocidad de
ventilador Low (Baja), Med (Media) o High (Alta), a fin de brindar
una circulación de aire y filtrado sin enfriamiento. Debido a que las
configuraciones de sólo ventilador no brindan enfriamiento, no se
podrá ingresar una temperatura configurada. La temperatura del
ambiente aparecerá en la pantalla.
Velocidad Automática del Ventilador
Configure en Auto (Automática) para que la velocidad del ventilador
se configure de forma automática en la velocidad necesaria para
brindar ajustes de confort ópt imos con la temperatura configurada.
Si se necesita más frío en la habit ación, la velocidad del vent ilador
se increment ará de forma automática. Si se necesita más frío
en la habitación, la velocidad del vent ilador se reducirá de forma
automática.
Función de Luces Encendidas/ Apagadasdel Panel de Control
Este acondicionador de aire cuenta con una función de panel de
control de luces encendidas/ apagadas, donde dichas luces se
apagarán cuando no haya actividad en los controles por más de un
minuto. Para reactivar los controles, presione cualquier tecla de los
controles y las luces se iluminarán para mostrar las configuraciones
previas.
Para desactivar esta función, mantenga presionada la tecla SLEEP
(Dormir), sobre la unidad, durante 5 segundos. La unidad emit irá un
pitido para señalizar que la función fue encendida o apagada con
éxito.
USO DEL ACONDICIONADORDEAIRE