Haier HWM8000 User manual

HWM8000
Fuzzy Computerized Automatic
Washing Machine User's manual
This manual is for
Please read this manual
carefully before using.
Retain it for future reference. 0030805704B

Contents
Names of the parts
Safety precautions
Trouble shooting * Answer to question
Packing list Specification
Installation and adjustment
Usage of the drain hose
Preparation before washing
Put in the laundries
Add the detergent and softener
Use the operation knobs and buttons
Installation the water inlet hose
Disposal after washing
*
Finish washing
Close the top lid

Adjustable foot
Front control
board
Front fixed
foot
Rear fixed foot
back cover
Cabinet
Drain hose
Back faceplate
Control panel
film
Control panel
Lint filter(Installed by user)
Filter cover
Level meter
Power line
Pulsator
Inner tub
Detergent box
Drier outlet
cover
Top lid B
Cabinet handle
Warm water valve
Cool water valve
Top lid A
Adjustable foot
seam
hanging hole
for the drain
hose
Names of the parts
Please check if the power receptacle has good earthing condition
before using to guarantee your safety.
Warning sign
Meaning and description of the symbols
Forbidding sign
Contents marked with that symbol are related
to the safety of the product and the personal
safety of the users. Please operate in strict
conformity to the contents, otherwise it may
cause damageof the machine or injure the
personal safety of the user.
Contents marked with that symbol are actions
forbidden to perform. Performing of those
actions may result in damage of the machine
or injure the personal safety of the user.
1

Safety precautions
In normal usage of thewashing machine,
the power plug shall be ready to be pulled
or plugged with hand. Be sure to pull the
plug off and close the water faucet in
following cases: power failure, delivering
the machine, setting the machine idle or
cleaning the machine. Do not plug
or pull the power plug with wet hand.
In case the washing machineis installed on
ground with carpet,be careful notto block the
ventilation hole withcarpet.
Do not letthe machine shareone receptacle withother
electric appliances. Ifthe power plugis damaged, orthe
plugging into thereceptacle is loose,do not useit any
more.
Do not set the machine at dampplace
like the bathroom.Never wash itwith water.
Do not put wet laundries on the control
panel coating.
Do not usewater with temperature
higher than 50 inside the tub.
Do notwash water-proof laundries like
the raincoat, bike covers,down textiles etc.
to avoid abnormalvibrations in spinning and
damaging the laundries.
Do not bend, stretch, twist, bind the power cord by force,
or reform it. Do not press or clamp it with heavy items. If the
power cord and power plug are bad, or the receptacle is loose,
be sure tohave it replaced by the techniciansof our special shop
or our agent, or the after-sale service department for the sake
of avoiding any risk. Keep the prong of the power plug clean.
If dust isfound on thepower plug, pleasewipe it offwith dry cloth.
The ventilation
holes at the
bottom
Please insert the power cord into special
receptacle with rated voltage.Be sure to
use single-phase three pins receptacle.
The earthing terminal must be earthed
reliably.If possible,please adopt electric
leakage protector.
2

Do not put hand intothe rotating tub. It is
dangerous even ifthe rotation speedis slow.
Take special care of thechildren. Keep
children away from the washing machine
to avoid themclimbing on it.
Do notdecompose, repair or alter
the machine byyourself.
Do not put any hot orheavy items
(such as thekettle with hotwater) on the
washing machine.
Do notwash laundries with volatile
materials (such asthinner, petroletc.).
Keep themachine away from direct
sunlight and heatsource like theheater.
The handicappedor children shall not
use the machinewithout care.
Safety precautions
Please check if the water faucet is open, and if
the connection of the water inlet pipe is proper.
It is suggested to use foamless washing powder.
Toprevent the lintin the tubfrom blocking
the cascade outlet and influencing the
cascade effect, please keep the lint filter
in good condition, and install it to proper
position during washing. If the lintfilter is
lost or damaged, please contact the local
after-sale service department of our
company.
To protect your laundries and washing
machine, please take out all of the coins,
buttons, sand, hairpin and other foreign
materials before washing.
3

Install the bottom plate
Adjust the installation position
Please install andadjust the machine according to the requirement of themanual, which is very
important for youto operate the machine safely and properly.
After openingthe package, please lean the
washing machine gently down on soft items
(like towel cloth, blanket, etc.). Install the
bottom plate to the bottom of the machine
with eight screws by a cross screwdriver,
then lift the machine up gently. See to the
figure:
Front
Back
Soft item
Screw
Bottom plate
Loosen Fasten
High Low
Adjustable nut
Adjustable leg
The largest allowableslope of theshank base
of the machineis 2 . The slanting or rough
ground will result in unstable running or
stoppage of themachine. Please adjustit with
following methods:
Confirm it's horizontal:
Adjust theadjustable leg:
If the bulb of the level meter at the balance display
position is inside the standard circle, it indicates that
the machine is horizontal. Otherwise you need to
adjust the adjustable leg of the machine.
1.Totwist the adjustable leg, please firstlift up the
leg side slightly, loosen theadjustable nut, and
then twist theleg.
2.After adjustment, fastenthe nut.
Air bubble
Standard circle
Suitable Not suitable
Installation and adjustment
4

Inner tub Lint filter
After openingthe package, please takeout the lint
filter from the document bag,install it to the filter cover
of inner tub.See to thefigure.
Install the lint filter
How to change the direction of the drain hose
1.The height of the drain hose shall be
less than 10cm, or the drainage will not
be smooth, and cost such long time that
the machine may stop at mid way.
2.Do not ramp or press the drain hose.
3.If the drain hose is too long, cut it at mid
point. To make smooth drainage, cut the
front end of the hose slantingly.
4.If extra drain hose is needed, please
make separate purchase. The inner
diameter of the extra hose shall not
less than 30mm, and the length shall
not exceed 1.5m.
Usage of the drain hose
The drain hose shall drain smoothly
1.Dismount the back cover of the washing machine.
2.Lay down the washing machine gently with the front
side facing the ground. Use cross screwdriver to
loosen the eight screws. Take off the bottom plate.
4.Dismount the protecting cover of the drain outlet at the
other side as indicated in Figure 3.
5.Extend the drain hose out of the other side. Fix the drain
hose onto the cabinet with the drain hose rack. Set the
drain hose nut on, and fasten the nut to the direction
indicated in the figure, as per Figure 4.
6.Install the protecting cover of the drain outlet to the other
side, as indicated in Figure 5.
7.Install the bottom plate (method the same as stated
above). Lift up the washing
machine gently.
3.Put down the outer drain hose. Twistthe drain hose nut
counterclockwise to take it off as indicated in Figure 1.
Take off the drain hose rack. Put the drain hose into
the cabinet as indicated in Figure 2.
back
front
bottom plate
Page 4
drain outlet
protecting
cover
fasten
drain hose nut
Drain hose nut Drain hose rack
Outer
drain hose
Loosen
soft item
Figure 1
Figure 3 Figure 4
Figure 5
Figure 2
f the extra hose is too long, cut it either
at point A or B.
5

Install the water inlet pipe
Connection between the water inlet hose jointer and the water faucet
Water faucet, suitable water faucet, not suitable
It is required that the front end shall be longer than 10mm.
The outlet end surface of the faucet shall be flat and smooth. If not, please file it smooth to avoid leakage.
2 Loosen the four screws of the water inlet hose jointer till the water faucet can be accessed. Then set the water inlet hose
jointer on the faucet. See to Figure 2. If the faucet is too large and the jointer cannot be set on, please loosen the four
screws and take out the bush inside the jointer. See to Figure 3.
1.Press the lower end of the lock lever and push down the slider. Take off the water inlet hose jointer from the
water inlet hose component. See to Figure 1.
3 Fasten thefour screws ofthe water inlet hose jointer evenly. See toFigure 4.
About 4mm after twisting
Remark: .Before installation, the threading is 4mm above the upper surface of the nut.
After installation, the threading is 2mm above the upper surface of the nut..
About above 2mm after twisting
Water inlet hose jointer
Screw knife
Screw
Bushing
Nameplate
Screw nut
Water inlet hose Figure 1
Figure 4
Figure 2
Figure 5
Figure 3
Figure 6
Slider
Lock level
Install the water inlet hose
4 Take off the nameplate.Twist the fastening nut as per the indication of the figure
to seal up the exit end face of the faucet. See to Figure 5.
Connection between the water inlet hose and the washing machine
1 Do not takeoff the waterabsorption cushion. Pleasecheck
if the cushion isdropped or damaged eachtime before using.
If it happens so,please duly contact ourafter-sale service
department.
2 Set the nutof the water inlethose on the waterinlet valve jointer.
3 Fasten the nut.Swing it gently toconfirm if it's fastenedwell.
Water absorption cushion.
Water inlet
hose nut
Water inlet valvejointer
6

Dismount the water inlet hose
Connection between the water inlet hose jointer and the water inlet hose
Check the connection between the water inlet hose jointer and the
water faucet
1.Swing the hosegently to checkif it is fastened stably.
2.After installation, openthe faucet tocheck if itleaks water.
3.Do not bendthe hose byforce.
4.Each time beforeusing, please checkif the connection
between the waterinlet hose jointerand the waterfaucet,
and the installation of the waterinlet hoseis firm,so as
to avoid droppingowing to improperinstallation.
1 Push downthe slider.Plug the waterinlet hose intothe jointer.
2 Hang thelock lever ontothe jointer.Release
the slider tilla click soundis heard.
Lock level
Slider
The water inlet
hose jointer
Slider
Locking level
1 Close thewater faucet.
2 Press thelock lever andpush down theslider. Thenpull off the
water inlet hose.If the machineis used more than once every
week, the waterinlet hose jointercan remain onthe faucet to
avoid damaging thefastening screws.
7

1 Preparation before washing
Pay attention to the followings before washing
Preparation before washing
1 Connect thewater inlet hose.Open the waterfaucet.
2 Confirm thatthe washing machineis earthed reliably.
Then plug thepower plug intothe receptacle. The
earthing terminal shallnot link togas pipeline and
faucet water pipeline.
3 Put downthe drain hose.
Check if
the laundries
have special
requirement
on washing
Clear the
pocket. Take
out the coins,
sand, hairpins
etc.
Tie the long
strips; fasten
the buttons;
close zippers.
When the pulsator
is running ,the
buttons of the
laundries may
cause noise. For
the sake of
discretion, please
put the laundries
with buttons into
other laundries.
The quantity of
the laundries
shall not be too
large. Stretch
and loosen the
laundries before
putting them in
the tub.
a. Check if the laundries are applicable for washing with machine.
b. Divide the laundries that are not colorfast from other laundries.
c. Put the laundries difficult to absorb water into water with hand.
d. For thelaundries with heavy soil, please first remove the dirt like mud or dust.
For the parts with heavy soil, please apply detergent on them in advance, which
can make it easier to remove the soil.
e. For thelaundries that may get lint ball and those with long fur, turn it over before
putting in.
f. Do notput the laundries polluted by chemicals into the washing machine directly.
4.Slanting or uneven ground may result in unstable
working or abnormal noise. Please make the machine
stand horizontally.
8

The capacity ofwashing and spinningrefer to the
largest weight ofthe standard laundriesunder dry
condition that canbe washed orspinned in one
cycle. Washing quantityfor one cycleshall be
less than therated capacity.
The thickness, sizeand type ofthe cloth will
influence the actualwashing capacity.It is
feasible to putin suitable amountof laundries and
the laundries canbe tumbled normallyin washing
for one cycle.
In using waterwith high temperature,please pay
attention to thewashing temperature limitstated
on the labelof the laundries.
2 Put in the laundries
How to use the whitener
Fill water to decided level. Dilute
the whitener with container. Pour
it slowly into the washing tub.
Avoid using whitener on laundries
with color or pattern as they are
prone to lose color.
The whitener shall not touch the
laundries directly.
Refer to the user's manual for the
usage and quantity of the whitener.
For powder whitener, please dissolve
it before use.
How to use the washing powder
Direct dissolved in the machine
1.Fill in small quantity of water.
(Select water level 1)
2.Add the powder. Run for 30 seconds to
dissolve it completely.
3.Put in the laundries. Select suitable
water level.
The instant dissolving of the washing
powder:
1. Prepare warm water of 30 and a
container.
2. Add the powder into the container
while stirring to fully dissolve it.
The powder is more prone to pollute the
laundries than the detergent. Therefore
please use it with proper quantity.
It is suggested not to use high sudsing
detergent.
Washing powder with poor quality or long
time storage may be caked. Please pay
attention to cleaning the detergent box in time.
3 Add the detergent and softener
Detergent box
Inlet for concentrated washing
powder and detergent
Softener inlet
Put the washing powder and softener into the detergent
box directly as indicated in the left figure.
After that, please close the detergent box. Refer to the
following table for the usage of the detergent: The
standard dosage of the detergent and the water
quantity
When you use softener, the softener must be lower
than the underside of water cap.
Please often wash the detergent box, because
softener may curdle easily.
How to use the softener
9

a Description of the function of the operation buttons
BALANCE DISPLAY
If the bulbof the levelmeter is inside the standard circle, it indicates
that the machine is horizontal.
CURRENT button
When the washing machine starts running, it
will set the currentautomatically.
You canselect current by selfaccording to the
actual requirement.
Please do not selectstrong current under low
water level to avoidsplashing and vibration.
In FASTand GENTLE programs, thewashing
machine will set thecurrent automatically,and
the users cannot selectcurrent in that case.
Select the fuzzy program. After clothdetection, the water
level will be setto one out of4, 6, 8, and10.
If there's water inside the tub, themachine cannot detect
the cloth and willdisplay water level 6
If wet laundries areput in, it maydisplay water level 10
You canalso set water level by self.After the machine is
started, it will notdetect the cloth.
If quick program isselected, the water level will be setto 2
automatically. When level is reached, itwill perform
washing while fillingwater. The2 water level indicator is
on, and the 4water level indicator is flashing. When the“4”
water level is reached,it will stop fillingwater. 2 level
indicator is off,and 4 level indicatoris on. It willperform
normal washing.
WATER LEVEL button
COOL
STRONG
CURRENT
WATER
LEVEL
WATER
INLET
BALANCE DISPLAY
4 Use the operation buttons
Cool water
WATER INLET button
In starting the machine,it is set toCOOL
WATER automatically
Push the button toselect one from thethree
modes of COOLWATER only, both WARM
WATER andCOOL WATER, or hot wateronly.
Note that the watertemperature inside the
tub shall not exceed50 .
No requirement on water temperature
Cool water
Warm water
If the hot water temperature is too high
and needs to be mixed with cool water
Warm water
When the temperature of hot water is
suitable, or when you need to improve
the water temperature inside the tub
Mode and meaning of the indicator
Flash: indicating the running mode
On: indicating the mode about to run
Flash rapidly: indicating abnormal situation
10

Standard Common washing
Night Low noise washing during night
Gentle Washing the woolen textiles or underwear
FAST 10-minute quick washing of laundries with light soil
PROGRAM button
The following four programsare available for your
option
SURPLUS
RESERVE HOURS LATER
FAST
GENTLE
FUZZY
STANDARD
NIGHT
SOAK
WASH
RINSE
SPIN
START
PAUSE
SELECT
PROGRAM
RESERVE
POWER
ON/OFF
Program
Push it to select one or more programs from SOAK
WASH RINSE and SPIN
After the power isswitched on, push itto start
the machine
During working, push itto pause working.
During pause, push itto resume working.
During sensing, itdisplays --
During operation ofprograms, it displaysthe
remained time (minute)
During reserve procedure,it displays the
remained reserve time(in hour)
In case ofabnormal phenomenon, itdisplays
the abnormal symbol(see to Page16)
SELECT button
START/PAUSE button
Digitron
Remarks: Push theOn/Off button toswitch on thepower. Ifthe washing machineis idle for5 minutes, itwill
automatically switch offthe power.
RESERVE button
Push the buttonto select washingfinishing time
between 2-24 hours.
When the RESERVEfunction is activated,the
RESERVE and TIMEREMAIN indicators areon.
The other indicatorsare off.
Push the RESERVEbutton to displaythe reserve
mode.
Push the On/Offbutton to switchon the power.
When the poweris on, pushit again toswitch
off the power.
POWER ON/OFF button
11

2 Push the program button to select suitable automatic program.
3 Push the select button to select suitable procedure.
After switchingon the power, the washingmachine will setto WASH-SPIN procedure
automatically. Itis the commonprocedure. To select other procedures, push theSELECT button to
select one ormore procedures fromSOAK, WASH, RINSEAND SPIN.Refer to PROCEDURE
SELECTION METHOD tomake selection.
After switching onthe power,the machine willset standard programautomatically. To select other automatic program,
push the PROGRAMbutton till the relative indicator is on.
Refer to thePROGRAM button onPage 11for the selection.
For instance: selectQUICK program forlaundries with smallquantity and lightsoil.
b Steps of using the operation buttons and description of each step.
In selecting thestandard and nightprograms, the
machine will executefuzzy program toselect
water level andwash time accordingto the cloth
and weight ofthe laundries. Thefull procedure is
controlled automatically.
COOL
WARM
SOFT
STRONG
SURPLUS
RESERVE HOURS LATER
MIN
FAST
GENTLE
FUZZY
STANDARD
NIGHT
SOAK
WASH
RINSE
SPIN
START
PAUSE
SELECT
SELECT
PROGRAM
PROGRAM
RESERVE
CURRENT
WATER
LEVEL
WATER
INLET
POWER
ON/OFF
POWER
ON/OFF
BALANCE DISPLAY
Page 13
Page 11
1 Push the POWER ON/OFF button to switch on the power.
FAST
GENTLE
FUZZY
STANDARD
NIGHT
Even there's nowater in thetub, a certainperiod
is required beforespin starting.
Do not usethe SOAK programfor the woolen
textiles.
Separate the laundriesthat are notcolorfast from
other laundries inwashing.
Attention
12

Times of pushing the
SELECT button
Push the SELECTbutton for 6times, and itwill resume the initial mode. Itwill circulate inthat sequence.
The SOAK procedurecan work incooperation with automatic programs like standardand night. Thereis
intermittent pulsator stirringduring soak.
Selected procedure Applicable circumstance Contents (the lightedindicators
indicate the programs about to run)
Spin
(spin after drain)
WASH
(the washing liquid
remains in the tub)
When the common laundriesneed
washing, rinsing and spinning. SOAK WASH RINSE SPIN
Repeat using the washingliquid
When the laundries needonly
spinning after manual washing (first
drain then spin)
The laundries are verydirty, orthe
sleeves and collars ofthe shirt are
very dirty.First soak then wash.
5 Push the WATER LEVEL button to select suitable water level
4 Push the WATER INLET button to select water inlet mode
After the power isswitched on, the washingmachine will execute fuzzyprogram automatically to detectthe cloth. After
defection, it can setthe water level automatically. To select other waterlevel, push the WATER LEVELbutton to set the
water level. Refer to WATER LEVELin Page 10 forselection.
After the poweris switched on,the washing machinewill set toCOOL WATER inlet modeautomatically. To
select WARM WATER onlyor both COOL WATER and WARM WATER, pushthe WATER INLET buttonto make
selection. See toWATERINLET in Page10 for details.
WATER
LEVEL
Page 9
Page 10
WASH - SPIN
RINSE - SPIN
WASH - RINSE
(the rinsing liquid
remains in the tub)
SOAK - SPIN
When prevent the laundriesfrom
corrugating, and the laundriesdo not
need spinning
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
SOAK WASH RINSE SPIN
Page 10
7 Push the RESERVE button to select suitable reserve wash program
6 Push the CURRENT button to select suitable water current
After the poweris switched on,the reserve programis set to off mode automatically. If you need to set thewashing
procedure to befinished at reservedtime, please pushthe RESERVE buttonto set the reserve wash program.Refer to
RESERVE BUTTON inPage 11for selection.
After the power isswitched on, the washingmachine can set thecurrent automatically according tothe laundries. If you
need to select currentby yourself, please pushthe CURRENT button.
Refer to CURRENTin Page 10 fordetails.
When the RESERVE function is activated, the indicator of the program you have set will be
off. The RESERVE (HOUR) and TIME REMAIN indicators will be on. During reserve
procedure, you can push the RESERVE button to display the reserve mode.
To change the running program or cancel the reserve setting, you need to switch off the
power and make new selection.
The washing will be finished after 18 hours.
Confirm the operation ofreserve program
Page 10
RESERVE
Reserve time from 2 to 24 hours
When the laundriesneed rinsing
And spinning aftermanual washing
13
Procedure selection method

5 Close the top lid.
6 Finish washing.
It beeps to indicatethe
finishing of washing
The power will be switched off automatically after the finishing of the washing.
If you open the top lid, the machine will stop working before spinning.
7 Disposal After Washing
If the cabinet isdirty, wipeit with wet softcloth
Do not wash with water directly.
Wipe with neutral detergent.
Do not wipe with thinner, petrol, alcohol, etc.
1.After washing, closethe water faucet.(If desired, dismountthe water inlethose).
2.Do not storewater in thewashing machine fora long period.Drain the watercompletely
after each using.
3.Be sure topull off thepower plug before maintenance.
4.Hang up thepower cord anddrain hose.
5.Wipe off thewater drops onthe surface of the machine andinside the tub.Open the toplid
for some time(about 1 hour),then close thetop lid.
Lint filter:
1.Pull it up todismount.
2.Push it down toinstall it.
3.After washing, clean thefilter screen
Dismount and installDismount CleanInstall
The filter screen islikely to be blockedby foreign
materials and influencewater inlet. Pleaseclean it
with brush frequently.
Please take offthe detergent boxand wash itwith water
1.How to takeit off: Pullit upwards slantinglyand gently.
2.How to install:Put it infrom the topslantingly, thenpush
it in to theright position.
14
Thinner
Alcohol
Petrol
8 Push the START/PAUSE button START
PAUSE

There may besome water flowing outof the drain
hose in the firstuse of the machine.
It is the waterremained in the machineduring the
ex-factory performance inspection.
Phenomenon Reason Howto solve
It rings after startingthe Reserve
function. The digitron displaysE0.
The water faucet leakswater
There's abnormal sound inside
the machine
The cascade current ispoor or
there's no cascade current.
The machine
does not act.
The safety switch acts, and the
spinning cannot work (after twice
automatic imbalance revising). The
digitron displays E3 and it rings.
The water inlet doesnot work, or is
too slow (cannot reach the water
level after about 15minutes). The
digitron displays E4 andit rings.
The drainage cannot work, or is too slow.
The digitron displays E1 and it rings.
After washing and rinsing,it stops
running during spinning.The
digitron displays E2 andit rings.
Common phenomena
Phenomena Explanation
The spinning isintermittent when it starts.
The wash procedurepauses.
The pulsator pauses during water filling in washing and rinsing.
In adding water,the pulsator performs stirringslightly
It is to balancethe laundries to avoidslanting.
The cloth sensor isdetecting the cloth. Itwill start
adding water after about48 seconds.
The program issetting the drain time.A certain
period is needed beforeit starts spinning.
It is to avoidsplashing during water filling.
It is to soakthe laundries more completely.
The top lid isopened.
Is the drain hoseblocked?
The top lid isnot closed.
Are the laundries putslantingly?
Is the machine slanting?
Is the machine slanting?
Are there any foreignmaterials?
Are the laundries putslantingly in
spinning?
Is the water faucetopened, or is there
water supply failure?
Is the water inletvalve blocked?
Is there foreign materialblocking
the spray outlet?
Is there power failure?
Is the power pluginserted tightly?
Is the water levelreached preset
position?
Is the screw ofthe water inlet hose
jointer loose?
Is the screw ofthe water inlet hose
jointer twisted awry?
Close the top lid.
Close the top lid.
Clean the foreign material.Push
the start button again.
Reorder the laundries. Closethe top lid.
Set the washing machinehorizontally and
then open and closethe top lid once.
Open the water faucet. Push the
Start/Pause button again.
Clean the water inletvalve then push the
Start/Pause button again.
Adjust the machine tobe even
Remove the foreign materials.
Reorder the laundries andclose the top lid.
Fasten the screw ofthe jointer properly.
Clear the foreign material.
Please use it whenthere's power supply.
Insert the power plugtightly.
Fill water to thepreset position.
Push the SPINbutton, but itdoesn't act.
(If there's breakdown, please pull off the power plug before checking) The following phenomena are not breakdowns
sometimes. Please confirm again before sending it to repair. If there are real breakdowns, please come to the special
maintenance department or after-sale service department of our company. Do not repair it by yourself.
Not wash
Not spin Is the power pluginserted tightly?
Is the top lidclosed reliably?
Are the laundries setflat?
Insert the power plugtightly.
Close the top lid.
Set the laundries flat.
No water inlet.
Is the power plug plugged tightly?
Is the water faucet opened?
Are the POWER ON/OFF and
START/PAUSE buttons pushed down?
Plug the power plugtightly.
Open the water faucet.
Push the power ON/OFFbutton and
START/PAUSEbutton.
The water temperature is too high.
The digital tube displays E5, and rings.
The temperature is higher
than 75 C. After cooling. Press theStar/Pause knob.
15
Trouble-shooting Answer to question

Packing list
User's manual One piece
Fuzzy computerized automatic
washing machine
Lint filter
Name
One piece
Eight pieces
One piece
One set
Tapping screws
Quantity
Bottom plate
Two pieces
Water level/Water quantity (about)
Injection pressure
Specification
0.03MPa-0.78MPa
The end connectingto
the washing machine
Jointer connecting
the water inlet hose
to the water faucet
The end connecting to
the water inlet hose jointer
1/23L, 2/30L, 3/34L, 4/40L, 5/44L,
6/49L, 7/53L, 8/57L, 9/61L, 10/66L
16