Haier WD-8888-19 User manual

1
HAIER
Twin-tub
Washing Machine
Service Manual
PART # WD-8888-19
HAIER AMERICA TRADING, LLC
www.haieramerica.com

2
Table Of Contents
Specifications 3
Circuit Diagram 4
External Dimension Sketch 5
Instructions for Installation 6
Product Briefs and New Features 8
Sequence List of the Timer 8
Common Troubleshooting 9
Instructions for Dissembling and Assembling 13

3
Specifications
Model XPB35- AS XPB30- AS
Rated load capacity, washing
and spinning 7.7lb 6.6lb
Rated voltage/ rated
frequency 120V~ 50Hz
Rated input power for
washing 260W
Rated Input power for
spinning 120W
Water quantity (L) Water level High about 40, Middle about 32, Low
about 25
Dimensions (inch) L 28.3 W 16.5 H 32.9
Washing pattern New current
Weight (lb) About 22.0
Water intake pressure (Mpa) 0.2x105Mpa ~ 2x 105MPa

4
Circuit Diagram
Protective device
●Washing motor is equipped with protective device.
●The overload protective device is inside the motor. When the motor is
overloaded or running into breakdown, the protective device will act to stop the
motor. When the breakdown is solved, the motor will resume running.

5
External Dimension Sketch
Figure 1

6
Instruction for Installation
It is important for your safety and proper use to install and adjust the washing
machine properly.
1. Locate the machine to scheduled position
a. After opening the package, please take out the machine gently and put it to
scheduled position.
b. If machine is installed at area with carpet, the ventilation hole will not be
blocked by the carpet.
c. Do not locate the machine near hearting source like the heater. Avoid direct
sunlight so as to prevent the plastic components from transforming and color
changing.
2. Adjust the installation position
The washing machine will become unstable on slanting and uneven ground.
Please adjust the installation position, or add suitable cushion under the foot so
as to make it stable. Hang the bucket with weight to see if the washing machine
is horizontal thus can guarantee stable working of the machine.
3. Do not share the socket with other appliances. Do not use power sources
other than the indicated one. Keep the power plug clean.
4. Install the earthing wire
The earthing terminal of the power plug shall be earthed reliably. Do not link it to
the water tap pipeline or gas pipeline.
5. Use of the drain hose
a. Put down the drain hose evenly on the ground. No high obstacles are
permitted at the middle part.
b. If the drain hose is too long for use, you can cut it at middle position.
c. Do not step on or squeeze the drain hose.
d. If you need extra drain hose, please purchase it separately from the original
hose dealer. However the length shall not be less than the original hose.

7
6. Install the water inlet hose
If the water inlet hose is installed poorly, it may drop under too high pressure and
result in leakage. The proper installation method is to put one end of it into water
and the other end into ejection joint of the control panel.
3.9 in

8
Product Briefs and New Features
●The product has good comprehensive performance. It adopts streamline
design with nice and graceful shape. The plastic shell is free of rustiness in its
whole working life.
●The product’s structure of washing frame and water-reception groove, reduces
the harmful effects of the vapor on the electric parts significantly. Therefore, it is
safe and reliable to use.
●The design of eccentric pulsator brings richer vibrant pattern and more even
washing effects.
●The fully enclosed base frame is water-proof and noise reducing. It can realize
"quiet washing".
●Having benefited from our comprehensive energy saving technology, the
product can work under wide voltage range. You need not worry about the
fluctuation of the voltage any more.
Time Sequence List of the Timer
The product integrates the traditional timer and the selector switch into one
component, therefore improving the reliability. It is also convenient to operate
and repair.

9
Common Troubleshooting
1. Inserted the power plug but the washing machine does not operate.
Washing part

10
Spinning part

11
2. There is rubbing sound in breaking.
3. The noise in washing is too large.

12
4. The pulsator rotates to one direction only (Release the washing timer).
5. The following phenomenon is not breakdowns sometimes. Please check again
before sending the machine for repairs.
Phenomena Reason
●Is the power off?The motor does not rotate
●Is the power plug inserted?
The motor does not rotate ●Are there hairpins, coins or metal
things taken into the washing tub?
●Are there laundries fallen into the
spinning tub?
●Is the front of the drain hose
blocked?
The drainage does not work
●Is the button set at the "Drain"
position?
●Is the spinning tub cover closed?The spinning does not work or the
spinning speed has become slow. ●Is the axle of the spinning tub twisted
with the laundries?
●Is the spinning overloaded with
laundries?
●Is the gland pressed in evenly?
●Are the laundries put slantingly?
There is abnormal sound and violent
vibration in spinning
●Is the machine located on even
ground?

13
Instructions for Dissembling and Assembling
1. Instructions for after-sale service
●Be sure to switch off the power in dissembling or repairing.
●In connecting the conductor wires, be sure to use the insulated crimp
connecting terminals and box and crimp the wire to reliable position.
●In welding the components, remember to twist the wire first, then weld and
insulate it to the switches with the iron.
●In welding the wires with iron, do not touch the resin and insulated parts of the
switches with the iron.
●The wires shall not touch the moving parts like the belt, motor pulley brake rod.
the sharp edges and the parts with high temperature.
●If the wires have metal part, the wires shall not touch the metal directly.
Insulator shall be used between them.
●After assembling, perform water inlet, washing and spinning. Every part shall
act normally. Confirm if the leakages, sound and vibration are normal.
2. Dissembling and assembling of the control panel components
Loosen the fastening screws. Move along the directions indicated in the figure to
dissemble the control panel. In installation, the beard shall be locked into the
insulation holes of the water reception groove and the spinning tub frame.
3. Dissembling and Assembling of the components of the spinning tub
frame
Dissemble the control panel. Loosen the two fastening screws at the rear of the
spinning tub frame, and then the spinning tub frame will be dissembled.
4. Dissembling and Assembling of the spinning tub
Dissemble the spinning tub frame and the fastening screw of the spinning tub
axle, and then the spinning tub can be taken out. In installation, the protruding
part of the brake wheel inner lining shall be imbedded into the groove on the
spinning tub axle.

14
Transmission of spinning tub.
5. Adjust the tension of the belt
Loosen the fastening screws at the back of the base frame. Move the shift-fixing
cushion along the direction indicated in the figure to adjust the tension of the belt.
After adjustment, you can fasten the screws.
6. Dissembling and Assembling of base frame
▪Dissemble the back cover
▪Loosen the conductor wire.
▪Loosen the fastening screws for the spinning tub axle.
▪Divide the spinning tub axle with the brake wheel.
▪Loosen the brake hook.
▪Dissemble the check band frame from the installation groove of the twin-tub.
▪Dissemble the V-belt.
▪Take out the drain hose from the beard of the base frame.
▪Loosen the fastening screws between the base frame and cabinet, then you
can take off the base frame.
7. Dissembling and Assembling of base frame
Once the bearing seat is dissembled, it cannot be used again. Therefore, do not
dissemble it as far as possible. If it has to be replaced, first dissemble it as per
following steps, then install a new one.
a. After dissembling the spinning tub as per description of clause 8.4, pull the
bearing seat.
b. Cut off the inner lining of the bearing seat with pliers and take it out.

15
Correct Incorrect
c. Use new bearing seat and inner lining
d. The bearing seat is a plugging component. Be sure to press it in with the claw
of the bearing seat inner lining seat aiming at the hole of the tub. You shall use
suitable tools and add pressure evenly around.
e. After plugging the bearing seat, confirm if the claw is installed to proper
position by checking the outside of the twin tubas shown in the picture above.