Haier WD9900 User manual

THOR WASHER/DRYER
INSTALLATION GUIDE
MODEL: WD-9900

Unpacking the Machine
The Thor Combination Washer/
Dryer must be unpacked prior to
installation. All packaging should be
removed from the machine. Two
water supply hoses with brass
pressure reducers, a drain hose U-
bracket, a wrench, and three plastic
inserts will be located in a bag inside
the drum.
VERY IMPORTANT
The shipping bolts located in the
back of the machine must be
removed prior to operating the
machine.
Unpack the machine. Properly
dispose of all packing
materials.
1.
Check for two (2) water supply
hoses with two (2) brass
pressure reducers on the red
end, one (1) drain hose bracket,
one (1) wrench, and three (3)
plastic insert caps.
3.
Summary
!
Open the door to the drum and
remove the bag containing
parts.
2.

Unscrew the three shipping
bolts on the back of the
machine using the wrench
provided or a 13 mm socket.
4.
Once the bolts are unscrewed
fully they can be removed from
the machine.
5. Cover the holes left by the bolts
with the plastic inserts located
in the bag of parts.
6.
Locations
of Shipping Bolts
!
NOTE - ONCE SHIPPING BOLTS ARE REMOVED RUBBER SPACERS MAY FALL
DOWN AND OUT THROUGH BOTTOM OF MACHINE. THIS IS NORMAL AND WILL
NOT CAUSE ANY HARM OR MALFUNCTION.

Connecting Water Supply and Drain
The machine should be located
within easy reach of the water
supply, the drain pipe, and an
electrical outlet The water supply
should be connected once the
machine is in the correct location,
followed by the drain hose. Drain
hose should be secure. All hoses
and connections should be checked
thoroughly before leaving machine
unattended.
IMPORTANT
For ease of installation only one (1)
pressure reducer needs to be used.
Both should be used under VERY
high pressure situations.
Normally only one pressure
reducer is needed. For above
normal pressure both reducers
may be necessary. For very
low pressure situations you
may leave both off.
3.
Summary
1. The brass pressure reducer
must be removed from both
hoses before they can be
attached to the machine.
When hoses are attached to the
machine care must be taken to
not strip the inlet valves.
2.
COLD HOT
!

Attach both inlet hoses to the
machine. The red end MUST
be attached to the machine, as
it has metric threading.
4. Attach both hoses to the water
supply. Be sure that the
correct hose is on the correct
inlet valve. (Hot-Hot; Cold-Cold)
Tighten all connections to
prevent leaks, but do not over
tighten.
5.
With Adaptor
The U-bracket must be attached
to the hose to hold it in the
drain. It is recommended that
4-6 inches of hose should be
left to go into the pipe.
5. Put the drain hose into the
drain pipe, securing it to make
sure that it cannot slip and
flood.
5.
4-6”

Leveling the Machine and Finishing Up
The QuietLine washer/dryer should
be installed on a level surface that is
well supported to prevent vibration.
Preferably the machine should be
installed on a solid and level floor
surface.
The machine must be leveled
properly before operation. This will
prevent excessive noise, vibration,
and possible damage to machine.
The QuietLine has four leveling legs
which can be adjusted and locked
for proper leveling.
Put the machine into its final
operating location.
1.
Using a level, check both front
to back and side to side on the
machine. If it is not level, make
appropriate adjustments to the
feet until it is.
2.
Summary:
To adjust feet, loosen locknuts
using the leveling leg wrench,
and screw the foot up or down
until the machine does not rock
and is level.
2.
REFER TO MACHINE’S MANUAL AND EZ WASH GUIDE FOR
OPERATING INSTRUCTIONS.

Hand tighten the locknuts
against the base of the
machine.
4.
Once the machine is level plug
into electrical outlet.
6. Turn it on/off using the button
located in the center of the
panel.
6.
Using the leveling leg wrench,
firmly secure the locknuts to
prevent the legs from slipping.
5.

FOR TECHNICAL SERVICE, HELP, OR
QUESTIONS ABOUT INSTALLING OR
INITIAL OPERATION OF YOUR THOR
COMBINATION WASHER/DRYER PLEASE
CALL
888-876-8002
www.OasisAppliance.com