Hakko Electronics FA-431 User manual

HAKKO FA-431 Fume extraction system
Power cord
Cap (inside main unit)
Remote control
2. SPECIFICATIONS
4. OPERATION
●HAKKO FA-431
Instruction Manual
Main filter (inside main unit)
Pre-filter
Instruction manual
1
10pcs.
1
FUME EXTRACTION
Thank you for purchasing the HAKKO FA-431 Fume Extraction system.
Please read this manual before operating the HAKKO FA-431 .
Keep this manual readily accessible for reference.
2015.12
MA02798XZ151201
To prevent accidents or damage to the HAKKO FA-431, be sure to observe the followings:
●Use only genuine HAKKO replacement parts.
●
Do not operate the fume extraction without the filter; otherwise it may cause the unit to malfunction.
● Hold the plug when inserting or removing the cord in/from the outlet.
● Do not allow the HAKKO FA-431 to become wet, or use it with wet hands.
● While using the HAKKO FA-431, don’t do anything which may cause bodily harm or physical damage.
1. PACKING LIST AND PART NAMES
Please check to make sure that all items
listed below are included in the package.
1
1
1
1
100 - 110V 120W 220 - 240V 110W
High Medium Low
4.7m³/min 3.7m³/min 2.8m³/min
97％(≧0.3μm)
ø55 mm
330(W) x 366(H) x 343(D) mm
7.2 kg
Power Consumption
Suction Capacity *1
Filtering Efficiency
Duct diameter
Dimensions
Weight (w/o cord)
OVERSEAS AFFILIATES
U.S.A.: AMERICAN HAKKO PRODUCTS, INC.
TEL: [phone] FAX: [phone]
Toll Free (800)88-HAKKO
4 2 5 5 6
http://www.hakkousa.com
HONG KONG: HAKKO DEVELOPMENT CO., LTD.
TEL: [phone] FAX: [phone]
http://www.hakko.com.hk
E-mail:[email protected]
SINGAPORE: HAKKO PRODUCTS PTE., LTD.
TEL: [phone] FAX: [phone]
http://www.hakko.com.sg
E-mail:[email protected]
Please access to the following address for the other Sales affiliates.
http://www.hakko.com
HEAD OFFICE
4-5, Shiokusa 2-chome, Naniwa-ku, Osaka 556-0024 JAPAN
TEL:[phone] FAX:[phone]
http://www.hakko.com E-mail:[email protected]
© 2016 HAKKO Corporation. All Rights Reserved.
*1 When using 2 ducts
* Specifications and design are subject to
change without notice.
This product includes such features as electrically conductive plastic parts and grounding of the unit
as measures to protect the device to be soldered from the effects of static electricity. Be sure to observe
the following instructions:
1. The plastic parts are not insulators, they are conductors. When making repairs or replacing
parts, take sufficient care not to expose live electrical parts or damage insulation materials.
2. Be sure to ground the unit during use.
3.WARNINGS, CAUTIONS, NOTES AND EXAMPLES
●Do not absorb combustible, explosive or corrosive gas.
●Store the fume extraction unit in a dry place.
●Do not block the exhaust vent of the fume extraction unit.
●Turn the power off when not in use, or left unattended.
●Turn the power off when changing parts or storing the
HAKKO FA-431.
●
This appliance can be used by children aged from 8 years
and above and persons with reduced physical, sensory or
mental capabilities or lack of experience and knowledge if they
have been given supervision or instruction concerning use of
the appliance in safe way and understand the hazards involved.
●Children shall not play with the appliance.
●Cleaning and user maintenance shall not be made by
children without supervision.
WARNING
CAUTION
4. OPERATION
1. Open the upper cover and then remove the
plastic bag from the main filter.
2. Put the main filter on the main unit. Set the
filter with the arrow pointing down
(as shown in the illustration).
3. Fit the pre-filter on top of the main filter.
Be sure the pre-filter lies flat and completely
covers the top of the main filter with no gaps.
●Set the filter
4. Close the upper cover
HAKKO FA-431
Fume extraction
system
Cap
Main filter
Pre-filter
Remote
control
Power cord
Pre-filter
Main filter
(facing the arrow
downward)
Duct set (Duct / Adapter / Rectangular nozzle or Round nozzle / Net)
● Duct set (not included)
or
Round nozzle
Net
Duct
(ø55 mm)
Adapter
Rectangular
nozzle
1. Connect the power cord to the power receptacle on the right of the unit.
2. Plug the power cord into a ground wall socket.
3. Turn the power switch on. Power lamp will light up.
CAUTION
・
Close the cover before turning the power switch on.
・Do not block the open port on purpose.
・When the fan is running, do not open the upper cover.
・Turn the power off when not in use. Failure to do so may result in shorter filter life.
・The main filter on the HAKKO FA-431 should be changed once per year as a general rule.
Continued use after the replacement period may result in malfunction.
CAUTION
Remove protective film before use.
CAUTION
Remote control operation does not switch off
the power of the HAKKO FA-431. (Only the fan
is stopped.) After work has been completed,
set the power of the HAKKO FA-431 main unit
to OFF.
※Fan of HAKKO FA-431 will operate in remote control.
(refer to the “●Operation of the remote control”)
Power lamp
(Green)
Flow selection
switch
Low High
Medium
Channel
set mode
Remote control
receiver
Exhaust vent
Inlet
※Adjust the flow suitable for working environment by using flow selection switch.
●Attach the duct
A. How to attach duct set
1. Refer to Figure 1(right), and attach the
nozzle and adapter to the duct.
Insert the nozzle and adapter until it stops,
turn the nozzle clockwise. Make sure the
nozzle and adapter are firmly attached.

Twist the nozzle tight enough to avoid
coming off.
(Fig.1)
1Insert the nozzle
until it stops.
Turn the nozzle clockwise.
2
Be sure the duct is
facing in the
proper direction
during assembly.
or
2. Fit the net on the nozzle. (Figure.2)
3. Insert the duct into the open port.
If using one duct, ensure the cap is in place
on the unused port.
When using two ducts, please store the cap
inside the main unit next to the main filter as
shown in Figure 3 (right).
(Fig.3)
(Fig.2)
Cap
● Fume extraction unit
Power switch
風扇組合
插頭

7. PARTS LIST
●Nothing happens when the power switch
is turned on.
●Even if a remote control button is pressed,
the fume extractor does not operate.
●Remote control channel cannot be set.
4. OPERATION
HAKKO FA-431 can be operated using the remote control.
● Operation of the remote control
5. MAINTENANCE
Performing proper and periodic maintenance extends the product life. Wear of the product will differ
depending on work environment, the quality and quantity of the solder and flux.
Apply the following service procedure as dictated by the conditions of the usage.
● Filter replacement timing
When replacing the filter, please be performed in a state in which the fan has stopped.
NOTE：
ON
OFF
CH 1 CH 2 CH 3 CH 4
OFF button
ON button
Channel selection
buttons
Theremotecontrolhasthefollowingbuttons:
●ON button
Starts the fan of the HAKKO FA-431.
●OFF button
Stops the fan of the HAKKO FA-431.
●Channel selection buttons (CH1 to CH4)
・Sets the channel of the remote control to the same channel as the HAKKO FA-431 main unit.
・When one of the channel selection buttons (channels CH1 to CH4 are selectable) is held
pressed together with the OFF button for 2 seconds or longer, sets the channel of the remote
control itself to the pressed channel.
※When the channels of the remote control and the HAKKO FA-431 are the same, pressing the
remote control's ON button will cause the fume extractor to operate. (Both units are initially
set to channel CH1.)
Example:Settingtochannel3
1. Set the flow selection switch of the HAKKO FA-431
to CH SET.
2. While holding the OFF button of the remote control
pressed, press CH3 and hold both buttons pressed
for approximately 2 seconds.
3. When channel setting has been completed, the LED
on the main unit will blink twice and the buzzer will
sound the same number of times as the set channel.
Holdpressedforapprox.2sec.
※When using multiple HAKKO FA-431 units, all fume extractors set to the same channel as
the remote control will operate when the remote control is used. Operation of fume extractors
according to the application can be performed by changing the channel setting of the fume
extractors as necessary.
If the remote control stops operating
completely, it might be because the
battery (CR2032) is completely exhausted.
Replace the battery.
CAUTION
If the above procedure is performed without setting the main unit's flow selection switch
to CH SET, only the channel of the remote control will be changed and operation by remote
control cannot be performed. If this occurs, perform the channel setting procedure again.
CAUTION
②
CR2032
①
●How to set the channel
7. PARTS LIST
6. TROUBLE SHOOTING GUIDE
CHECK :
ACTION :
CHECK :
ACTION :
CHECK :
ACTION :
CHECK :
ACTION :
CHECK :
ACTION :
CHECK :
ACTION :
CHECK :
ACTION :
CHECK :
ACTION :
Is the power cord disconnected ?
Connect it.
Is the main filter set properly ?
Fit the main filter properly before turning
on the power switch again.
Is the flow control set to CH SET ?
Adjust the flow suitable for working environment
by using the flow selection switch.
Is the flow control set to CH SET ?
Adjust the flow suitable for working environment
by using the flow selection switch.
Are the remote control and HAKKO
FA-431 set to different channels?
Set both units to the same channel.
Is the battery of the remote control
exhausted?
Replace the battery.
Is the flow selection switch set to a
setting other than CH SET?
Set the flow selection switch to CH SET.
Is the battery of the remote control exhausted?
Replace the battery.
Instruction manual in the language of Japanese, English, Chinse, French, German and Korean
can be downloaded from the HAKKO Document Portal.
(Please note that some languages may not be available depending on the product.)
●HAKKO FA-431
Pre-filter
Main filter
Cap
Knob
Power switch
Power cord, 3 wired cord but no plug
Power cord, 3 wired cord & BS plug
Power cord, 3 wired cord& European plug
Power cord, 3 wired cord & BS plug
Power cord, 3 wired cord & Australian plug
Power cord, 3 wired cord & Chinese plug
Power cord, 3 wired cord & American plug (B)
Power cord, 3 wired cord & SI plug
Power cord, 3 wired cord & BR plug
Power cord, 3 wired cord & American plug (U)
Remote control
1
2
3
4
5
6
7
A5034
A5033
B3619
B1486
B2852
B2421
B2422
B2424
B2425
B2426
B2436
B3508
B3550
B3616
B3641
C5035
Part No. Part Name Specifications
Item No.
10 pcs.
220 - 240V
India
220V KTL , 230V CE
230V CE , U.K.
China
U.S.A.
Specifications
1
2
10
5
7
4
36
34
9
9
8
11
●Option
Duct set /
Rectangular nozzle
Duct set /
Round nozzle
Duct
Adapter
Adapter
Rectangular nozzle
Round nozzle
Bench top hood
Net
Duct
Duct band
Sub-filter
Sub filter / for rectangular nozzle
Sub filter / for round nozzle
Filter case / for rectangular nozzle
Filter case / for round nozzle
Duct (1) / Adapter (1)
Rectangular nozzle(1) / Net (1)
Duct (1) / Adapter (1)
Round nozzle (1) / Net (1)
φ 55 mm
For 3 inch
5 pcs.
For 3 inch (φ 75 mm)
Set of 2
5 pcs.
20 pcs.
20 pcs.
C1571
C1572
B3642
B3620
B3621
B3622
B3623
B2418
B3625
B2410
B2416
A5035
A5036
A5037
B5146
B5147
Item No. Part No. Part Name
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
12 13
14
15
16
7