HAKO 7091.25 User manual

Assembly Manual
LED working light (7091.25)

2
Foreword
The installation procedures described
in this assembly manual should only be
undertaken by a Hako service centre or
a workshop authorised by Hako. 
Members of staff with the required level
of training and expertise are only 
guaranteed in the said workshops.
This assembly manual may be used
only in conjunction with the operating
manual of the machine.
Safety instructions
Please observe the general safety 
regulations of the corresponding 
machine in the relevant operating 
manual.
Place the machine on a level surface
and secure it with the parking brake.
Switch the machine off and pull out the
key.
We would expressly advise you that no
legal claims may be asserted based on
the contents of this manual. In the case
of necessary repair work, please make
sure that only original spare parts are
used. Only original spare parts guaran-
tee constant and reliable operational
readiness of your machine. We reserve
the right to make changes in the 
interests of further technical 
development.
Valid as from: September 2017
Hako GmbH
23843 Bad Oldesloe, Germany
Hamburger Str. 209-239
Phone [phone]
Introduction

3
LED working light
1 LED working light
1.1 Parts list
1 1x LED working light compl.
2 1x flanged button head bolt M5x12
(Torx)
3 1x corrugated hose holder
1.2 Before installation
1. Placethemachineonalevelsurface
and turn it off.
2. Open the seat console.
3. Remove the bolts of the cover
(Fig. 1/4).
4. Remove floor mat in footwell.
5. Remove floor plate (Fig. 1/5).
Fig. 1
4
1
2
3
5

4
LED working light
1.3 Installing the working light
The working light is installed on the left
next to the front wheel (Fig. 2/1).
1. Screw flanged button head bolt
M5x12 (Torx) with working light into
existing hole (Fig. 2/2).
2. Insert corrugated hose holder into
existing hole (Fig. 2/3).
3. Secure cable of working light to 
corrugated hose holder in such a
way that it is free of tension.
4. Lead cable through floor opening
into the electronics area (Fig. 2/4).
5. Connect plug of working light 
(Fig. 2/5) to 2-pin connector E01 of
cable loom W 2 (Fig. 2/6).
1.4 Adjusting the working light
Align working light so that it is 
straight-ahead in the direction of travel.
Adjust tilt in accordance with required
floor illumination.
Fig. 2
4
1
23
5
6

5
LED working light
1.5 Configuration menu
The LED working light option must be
activated via the configuration menu.
Value for LED working light:
A= Chapter
B= Configuration
C= Content
1.5.1 Button assignment
Button 1 (Fig. 3/T1):
Toggle between menu items A, Band
C.
Button 2 (Fig. 3/T2):
Change the values in the respective
menu item.
Button 3 (Fig. 3/T3):
Save the changed value.
Fig. 3
Option A. B. _. C.
LED working light 1. 6. _. 1.
4
3
T1
T2
T3

6
LED working light
1.5.2 Setting in the
Configuration menu
Requirements:
• Batteries inserted
• Diagnosis plug 97097737 available
Preparation:
1. Placethemachineonalevelsurface
and hold it with the parking brake.
2. Open the seat console.
3. Remove the bolts of the cover.
4. Carefully remove the cover from the
front, ensuring that the plug of the
on-board charger is not pulled out.
5. Connectdiagnosisplug97097737to
plug A1.X3 (Fig. 3/2) of the
control electronics A1.
Setting:
1. Open the configuration menu:
Press buttons 1 and 2 simultaneous-
ly,switch on thekey switch (Fig. 3/3)
and hold for 3 seconds. The right-
hand dot flashes in the indicator
(Fig. 3/4):
2. Press button 2 twice.
The chapter is now set to 1. The dot
next to 1 flashes:
3. Press button 1 twice.
The dot to theright of configuration 1
flashes:
4. Press button 2 five times.
The configuration changes to 6:
5. Press button 1 once.
The dot to the right of the content 0
flashes:
6. Press button 2 once.
Thecontent changesto1. The dot to
the left of the content goes off.
7. Press and hold button 3 for
3seconds to save the setting. The
dot to the left of the content appears.
8. Remove the diagnosis plug from the
control electronics and reattach the
cover.


7
LED working light

Advanced Technology for a Cleaner,
Better Environment
Hako GmbH ·Head Office · Hamburger Str. 209-239 ·23843 Bad Oldesloe ·Germany
Phone [phone] ·Fax [phone]
88-10-3125 - 3650-36