HALE MM-03 Release note

Approved according to EU Directive 2014/32/EU.
The HALE quality management system complies with the requirements
of standards EN ISO 9001:2015 and IATF 16949:2016.
Driver manual
Mirror Meter MM-03 / ITM30
Version 1.1 / 17.11.2020
Author: 55, 60
© by HALE electronic GmbH / Salzburg, Austria

Page 3
Table of Contents
Table of Contents
Introduction ................................................................................................................................................................................. 4
Display and Operation............................................................................................................................................................... 5
Operation - Driving Mode.......................................................................................................................................................... 7
Operation - Extras...................................................................................................................................................................... 9
Extended Extras Selection Mode EEM (depending on tariff)......................................................................................... 10
Operation - STOPPED................................................................................................................................................................ 11
Credit customer numbers........................................................................................................................................................ 12
Operation - VAT Selection....................................................................................................................................................... 14
Operation - FOR HIRE............................................................................................................................................................... 15
Printing a Receipt...................................................................................................................................................................... 17
Operation - All-inclusive Trip.................................................................................................................................................. 18
Operation - Totalizers.............................................................................................................................................................. 20
Starting the Shift ...................................................................................................................................................................... 22
Active Break............................................................................................................................................................................... 24
Passive Break ............................................................................................................................................................................ 26
Shift log-off................................................................................................................................................................................ 27
Signed-Off Mode....................................................................................................................................................................... 29
Date and Time ............................................................................................................................................................................ 31
Manual Sleep Mode.................................................................................................................................................................. 33
Automatic OFF Mode............................................................................................................................................................... 34
Automatic Sleep Mode............................................................................................................................................................ 35
General Information................................................................................................................................................................. 36
Starting a Shift with the Driver Card.................................................................................................................................... 37
Ending the Shift with Driver Card......................................................................................................................................... 38
Remarks and Warnings.......................................................................................................................................................... 40
Warnings Driver Card................................................................................................................................................................ 41
Printer Remarks and Warnings............................................................................................................................................. 42

Page 4
Introduction
Symbols
This information draws your attention to dangers or possible incorrect operation.
This tip provides you with advice or further information.
MNOP Press the corresponding button.
`This symbol means that you should do something.
ZSee page x (Zpage x)
Modes of Operation
Normal Operation For single proprietors: no shi operation
Operation with
Driver Log-on
For multi cab owners: the driver starts the shi by entering the driver number,
confirming it with button Pand pressing the buttons N+ O.
NFC Operation
With or without
data storage
For taxi fleets: Each driver starts his shi by holding the driver‘s card in front of the
NFC reader and pressing the buttons N+ O. The shi is ended by pressing the but-
tons N+ Oand holding the driver‘s card in front of the NFC reader (the data of the
ended shi is copied onto the card and can be evaluated in the HALE data center).
Introduction

Page 5
Display and operation
Display and Operation
Display and Buttons of the Taximeter
1-6 Operating buttons
Button 6 long = Switch on/o Stopped light (key-
board print), e g. in FOR HIRE (can be deactivated
in the tari)
7Alphanumeric tari display (2 14-segment-digits),
status display HIRED/STOPPED, N/H: Night or
holiday tari
8Status display FOR HIRE
TAXI: roof sign status display (if taxi sign flashes
=> defective roof sign illumination)
Extra display
9Waiting time display
Break display
Working time display
Extended extras selection mode (EEM)
Kilometer price displaya(€/km)
10 Fare display
a. only distance counter, not necessary for taximeter function
7-segment alphabet (alphanumeric display)

Page 6
Display and operation
NFC card
NFC card
NFC reader
For the ecient use of the NFC card it is important to always hold it in front of the NFC reader in such a way
that it overlaps the reader as much as possible.

Page 7
Operation - Driving Mode
Switch taximeter on*
`In sleep mode press button Mto switch to FOR HIRE, break
mode or mode between shis.
Operation - Driving Mode
When switching on the ignition the taximeter boots up for approx. 15 seconds (if it was in OFF mode).
The sleep mode is ended automatically aer ignition on or a driven distance.
Start a trip
`Press button Min FOR HIRE. If programmed in the tari,
button Ncan also be used (2,5 seconds).
Enter driver number resp. start shi (page 22) or start the shi with driver card (page 37).
* When switching on, an automatic display segment test is made, befor the taximeter is ready for opera-
tion.

Page 8
Switch back to previous tari
`Press button N(if programmed).
If programmed in the tari, button Pcan also be used.
Operation - Driving Mode
Switch to next tari
`Press button Magain.
If programmed in the tari, buttons Por Ncan also be
used.

Page 9
Entering Extras (depending on tari)
`Press button O(extra 1) or button P(extra 2) repeatedly
until the requested amount is displayed.
Operation - Extras
Delete Extras (depending on tari)
`Press button Pto delete extras separately.
If programmed in the tari, extras can also be charged automatically (controlled by the taximeter).
Operation - Extras

Page 10
`Press button Ountil the taximeter changes to the exten-
ded extras selection mode.
Extended Extras Selection Mode EEM (depending on tari)
`Enter the various extras with the buttons MN or O.
`Exit the extended extras selection mode or change to the
next EEM with button P.
Extended Extras Selection Mode EEM
Deleting extras (depending on tari)
`Delete the extras by pressing the buttons MN or Ofor
a long time.
The EEM is le automatically aer 10 seconds without keypress.

Page 11
Adding extras together
`Press button Pin STOPPED mode.
The sum total of the fare and extras is displayed for 5 sec.
(time period programmed in the tari).
Operation - STOPPED
Switching the Taximeter to STOPPED
`In the highest tari step press button M.
Info: If programmed in the tari, you can also switch to
STOPPED mode from any tari with button P.
If programmed in the tari, it is possible to switch from STOPPED mode to the previous tari by pressing
button N.
Operation - STOPPED
In the STOPPED position the interior light switches on automatically.

Page 12
Operation - Credit customer numbers
Credit customer numbers
Manual input
`Press button Pin STOPPED for 2
seconds to change to the mode for
entering credit customer numbers
(if programmed).
`Enter the credit customer numbers
with the buttons Mand N.
(1 - 999999; 0 = cancellation trip).
`Confirm with button P.

Page 13
Operation - Credit customer numbers
`Press button Mto change the num-
ber again.
`If you like to end the trip without cre-
dit customer number, press button
Nor wait in the input mode, until it
is le automatically aer 20 seconds.
`Press button Pto confirm the credit
customer number.

Page 14
`When switching to FOR HIRE, button Mchanges between
VAT rate 1, 2 or 0% (depending on the owner settings).
`Switch to VAT rate 2 by pressing button M.
`Switch to 0% by pressing button Magain.
`Confirm the selected VAT rate with button P.
`Or wait 5 sec., while no key is pressed. The displayed
value is taken over.
Operation - VAT Selection
Operation - VAT Selection

Page 15
Switching the Taximeter to FOR HIRE
`In STOPPED mode, press button Muntil the taximeter
changes to FOR HIRE or the display starts to flash.
The display flashes if the taximeter has been in STOPPED
mode for less than 10 seconds (time period is programmed
in the tari).
Operation - FOR HIRE
Displaying the Last Fare
`Press button Oin FOR HIRE mode.
The fare and extras for the last journey are displayed for
5 seconds (not possible aer an empty trip of 400 - 500
meters or aer 255 seconds).
Operation - FOR HIRE

Page 16
`In FOR HIRE mode, press button Puntil the status dis-
play of the roof sign goes o or lights up again.
In this way you can switch o the roof sign when driving
to a customer. Upon the next activation, the roof sign is
switched on again automatically.
Switching the Roof Sign on and o
(This feature can be disabled by the owner)
Operation - FOR HIRE
Taxi sign illuminated.
Roof sign is switched on and lit up.
Taxi sign flashes.
The roof sign is switched on, but no current is detected
(roof sign not working).
No taxi sign.
Roof sign is switched o.
Roof sign display

Page 17
Switch Taximeter to FOR HIRE
`In FOR HIRE mode, press button Ountil the printer starts
to print (not possible aer a trip of 500m + distance
from F3.0100 (standard 100m)). If allowed in the tari,
the print-out can be stopped with button P(if no forced
receipt printing has been set).
Printing a Receipt
The fare and extras for the last trip are displayed.
Printing a Receipt
Setting the print-out parameters of the receipt: Zowner manual.
RECEIPT No. 1
Transport & Co.
13:31 - 13:42 17. 2. 2015
K p/km 24000
MAX. SPEED km/h 102
ATCS B87B 36E8
LICENCE No. 10101
DRIVER No. DRI 1
CAR No. VEH 65534
DISTANCE km 3.0
FROM: ........................................
TO: ..............................................
TARIFFS 1,2
FLAG DROP € 3,50
FARE € 5,90
EXTRAS:
AIRPORT € 2,40
1 x 2,40
TOTAL € 11,80
incl. VAT
TIP €
Thank you for using our service!

Page 18
All-inclusive Trip (if programmed)
`In FOR HIRE mode, press the buttons Nand Pat the
same time.
The first digit flashes.
Operation - All-inclusive Trip
Operation - All-inclusive Trip
Entering an All-inclusive Price
`Press button Mto increase the value of the flashing digit.
`Press button Nto change to the next digit.
`Press button Pto confirm the price.
Aer a time set by the owner (standard 20 sec.), you can
still correct the all-inclusive price:
`Press button Nto return to the all-inclusive price input.

Page 19
Switching the Taximeter to STOPPED
`Press button Mto switch to STOPPED.
Switching the Taximeter to FOR HIRE
`Press button Muntil the taximeter changes to FOR HIRE
or the display starts to flash.
Operation - All-inclusive Trip

Page 20
Reading o the Shi Totalizers
`In FOR HIRE mode, press button N- the current shi
number is displayed.
`Press button P- the first shi totalizer (total km) is
displayed.
Operation - Totalizers
The 14 shi totalizers of the taximeter (d1 - d14) contain the current values of the ongoing shi and are auto-
matically reset at end of the shi.
Operation - Totalizers
Switching to next Totalizers
`Press button Pto change to the next totalizer.
Switching to previous Totalizers
`Press button Oto return to the previous totalizer.